Simple 2x2 Framed Outdoor Coffee Table

simple outdoor coffee table plans
Difficulty
Beginner Projects
| Print this plan

Project plan for a DIY Outdoor Coffee Table. Features simple styling, a lower height- Uses off the shelf lumber.

simple outdoor coffee table plans
simple outdoor coffee table plans
Dimensions
simple outdoor coffee table plans

Preparation

Shopping List
  • 5 - 1x3 @ 8 feet long
  • 3 - 2x2 @ 8 feet long
Common Materials
2 1/2 inch screws
1 1/4 inch finish nails
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Cut List
  • 9 - 1x3 @ 43" (Tabletop Boards)
  • 2 - 1x3 @ 24 1/2" (Breadboard Ends)
  • 2 - 2x2 @ 43" (Side Aprons)
  • 5 - 2x2 @ 19 1/2" (Supports)
  • 4 - 2x2 @ 13 1/4" (Legs)
Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Circular Saw
Brad Nailer
Power Sander
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

This project can be built with either countersunk screws or the Kreg Jig. I give directions for both in the diagrams.  You can click on any diagram for an expanded view.

If you are using the Kreg Jig, go ahead and mark all pocket holes and predrill, with your jig set for 1 1/2" stock, as shown above.
Otherwise, predrill holes with a countersink bit and fasten with 2 1/2" wood screws and glue.

Step 2

You will need to build two legs as shown above. 2 1/2" screws and wood glue.

Step 3

Attach leg sections to tabletop section as shown in diagram. Adjust for square.

Step 4

If you have a Kreg Jig, please skip to Step 6.

I used 2" finish nails and glue to attach the breadboard ends first. Ends overhang an inch, inside is flush to leg section inside.

Step 5

Step 6

For Kreg Jig users . . . drill pocket holes in all tabletop boards as shown above, set for 3/4" stock. Use 1 1/4" pocket hole screws and wood glue to fasten tabletop boards to breadboard ends. Make sure the tops are nice and flush.

Step 7

Once your tabletop is built, position the base centered on table, with 1" gap around all sides. Screw base to tabletop with 2" screws and glue.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

Comments

In reply to by bhoppy

Ana White

Wed, 06/08/2011 - 07:51

I made mine without :( and regretted it. Just has such a nice touch with the breadboard ends. Just finished up the end tables, and will post shortly, and they look so much better with the breadboard ends. If you choose not to make the breadboard ends, simply cut your tabletop boards to 48" lengths.

PA PA B

Wed, 03/28/2012 - 06:42

Anna, Looks great. What type of wood did you use? I am concerned about using a non treated wood for the outdoors. Is there a special finish needed if the wood is pine?

herzo1852

Wed, 07/31/2013 - 10:18

It looks so good, I can't thank you enough for this plan. I did change it to a 3 ft x 3 ft table and I varied the thickness of some of the top slats too, which was partially me wanting to be different and partially me having some 1x4 spare that I really didn't want to throw away, but it was too short for pretty much everything else I tried except the table top slats! Now working on 2 loveseats - having a BBQ on Aug 17th, going to be all done by then!