Face Frame Wall Kitchen Cabinet Universal Template

diy kitchen cabinets face frame
Difficulty
Intermediate
| Print this plan

Building kitchen wall cabinets is actually pretty straight forward.  With just a little know how and a few tools, you can create just about any kitchen wall cabinet.  In this free template, I show you how to build face frame kitchen wall cabinets.

MATCHING BASE: Face Frame Base Kitchen Cabinet Universal Template

diy kitchen cabinets

It's easy to build your own kitchen wall cabinets with face frames.  The face frame is wood trim around the front edge of the cabinet that helps strengthen the cabinet, and trim out the front of the cabinet.  A face frame is optional but adds lots of strength and beauty to the cabinet.

 

WHAT DO YOU NEED TO BUILD YOUR OWN CABINETS?

  • 3/4" Hardwood Plywood
  • 1x2 Hardwood for face frames, I use poplar for painted finishes
  • 1/4" plywood for the back
  • 1x3 or 1x4 pine wood boards for bay supports
  • Cabinet doors and concealed full overaly hinges for face frame cabinets
  • Shelf pins if adjustable shelves
  • For tools, I recommend a table saw, miter saw, drill, pocket hole jig, 18 gauge brad nailer, power sander, and standard hand tools

 

RECOMMENDED DIMENSIONS

  • Depth of 11-1/4" is standard.  Deeper cabinets can be 15-1/4" but it gets difficult to reach the contents in the back of the cabinet and obstructs lower countertops
  • Width of up to 36" is standard.  Wider widths may create sagging shelves.
  • Height of 30" is standard.  42" is common, as this is the full height cabinet when installing on 8 foot tall walls.
  • Bay = 1 is standard

CONFIGURING WITH ANA'S FREE EASY TO USE DESIGN APP

Use Ana's Free Furniture Design App to create custom plans, even in odd sizes.  It's super easy to use and you can download the plans in seconds.

Below is a standard 36" cabinet carcass.  Once you have the carcass set, everything can just be measured off the carcass.

 

 

CUTTING THE PIECES

When you complete your custom design, download the plans.  Rip 3/4" hardwood plywood into the desired width and cross cut with a miter saw to get the exact cuts needed.

 

ASSEMBLING THE CARCASS

simply drill 3/4" two pocket holes on each end of the shelf boards (horizontal) and attach to the vertical side boards with 1-1/4" pocket hole screws.  The shelves can be adjustable with shelf pin holes.

 

BAY SUPPORT

You'll need something to keep the cabinet from racking and to attach to the wall.  A 1x3 bay support at the top back is recommended, attach to both sides and top shelf.

FACE FRAME

For the face frame, we recommend poplar 1x2s for paint grade, and for stain grade, wood of your choice, preferably a hardwood as the face frame will take much use and may support hinges.

Cut the face frame stiles to match the height of the cabinet from 1x2s.  Then measure and cut to fit the face frame rails (horizontal 1x2s)

Attach the face frame boards together first with 3/4" pocket holes and 1-1/4" pocket hole screws.  Then use glue and 1-1/4' brad nails to attach face frame to front of cabinet.

CABINET DOORS

For face frame cabinets, there are different overlays for hinges.  The most common is 1-1/4" or sometimes referred to as "full overlay" for Concealed Face Frame Hinges.  This type of hinge is usually available off the shelf at most hardware stores.

For the 1-1/4" overlay hinge, measure the doors as shown in the diagram below.

  • Door width is opening width + 2-1/2"
  • For double doors, simply divide in half
  • The height is the opening height + 2-1/2"

CABINET INSTALLATION

The cabinet must be hung to studs in the wall behind the cabinet, through the top bay support, using self tapping construciton screws.  We also recommend attaching cabinets together through the sides using 1-1/4" self tapping construction screws.

 

 

Preparation

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Kreg Jig
Drill
Circular Saw
Miter Saw
Table Saw
Brad Nailer
Power Sander