Rustic X Coffee Table

Submitted by Ana White on Tue, 07/09/2019 - 10:40
Difficulty
Intermediate
| Print this plan

You can build a beautiful coffee table out of lumber!  For about $50 in materials, this solid wood coffee table with it's X detailing could be yours.  Our free plans include step by step diagrams, shopping lists and cut list - everything you need to get started.

Also in this collection: Rustic X Console Table, Rustic X End Table, and Rustic X Bench Plans

Collections
rustic x coffee table plans
rustic x coffee table plans
rustic x coffee table plans
rustic x coffee table plans
rustic x coffee table plans
rustic x coffee table plans

 

Remember a bit back when Hillary  from The Friendly Home built this amazing Rustic X Console Table from 2x4s? 

We've had so much interest from readers, we thought we'd add a coffee table plan to the collection.  

This coffee table is so gorgeous, it's hard to believe it's made from standard off the shelf lumber!

I ENCOURAGE you to stop over and visit Hillary and read about how she battled a wild fire to build this coffee table!  

PS - Hillary is also sharing her finishing tutorial.

Dimensions
rustic x coffee table dimensions
Dimensions are shown above.

Preparation

Shopping List
  • 2 – 2x4 – 8 feet or stud length
  • 4 – 2x2 – 8 feet
  • 1 – 1x12 – 8 feet long
  • 5 – 2x6 – stud length
  • 1 ¼” and 2 ½” Pocket Hole screws
Cut List
  • 4 – 2x4 @ 16 ½” (legs)
  • 4 – 2x2 @ 41” (side trim)
  • 4 – 2x4 @ 22 ½” (end trim)
  • 2 – 1x12 @ 41” (bottom shelf)
  • 2 – 2x2 @ 22 ½” (both ends cut at 60 degrees off square, long point to short point, ends are parallel)
  • 4 – 2x2 @ 11 ¼” (long point to short point, one end cut at 60 degrees off square, other end cut at 30 degrees off square, ends are not parallel but are cut in same direction)
  • 5 – 2x6 @ 52” (tabletop boards)
Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Miter Saw
Brad Nailer
Power Sander
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

First build the two side trim pieces.

Step 2

Then connect together. Hide top pocket holes on top, bottom pocket holes on bottom. NOTE: This plan is sized for 1x12 boards measuring 11 1/4" wide - measure your 1x12 boards, double that number, and cut your side trim to fit - see next step.

Step 3

Build your bottom shelf with 3/4" PHs/1 1/4" PH screws down center. Then drill 3/4" PHs around all outside edges and attach to the bottom shelf.

Step 4

Now attach cut and build the X braces. Attach in place. These are mostly decorative, so don't stress about getting them super screwed in place. Some good glue and screws will do the trick.

Step 5

For the top, we recommend building the entire top with 1-1/2" pocket holes and 2-1/2" pocket hole screws on a flat level surface.

Then attached the completed top to the base.
 

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

Comments

softballmamma

Mon, 08/05/2019 - 07:09

I just made this and the two end tables yesterday. I used Valspar heavy cream for the frame and used min wax espresso for the tops and bottom shelves. I also did not use wood conditioner prior to stain. I put on with a foam brush and wiped of immediately, I absolutely love them. I find that the coffee table is too high for use as a coffee table. So I am now using as a TV stand and will rebuild a coffee table better suited.