Rustic X Console Table

Submitted by Ana White on Tue, 05/21/2019 - 09:08
Difficulty
Intermediate
| Print this plan

Build the super popular Rustic X Console Table.  This woodworking project has been built thousands of times and loved the world over.  Its made of construction lumber (yes, 2x4s!) and the plans are easy to follow.  Free step by step plans from Ana-White.com.

Also in this Collection: Rustic X Coffee Table Plans, Rustic X End Table Plans and Rustic X Bench Plans

Collections
ana white rustic x console table
ana white rustic x console table
ana white rustic x console table
ana white rustic x console table
ana white rustic x console table
ana white rustic x console table

Rustic X Console Features

  • Solid wood design accepts stain beautifully and paints up nicely
  • Extra long length perfect behind sofas, sectionals, as a dining room buffet, or under the TV
  • Storage shelves perfect for displaying and storing 
  • Storage shelves fit most standard baskets
  • Beautiful planked top is full of texture
  • Step by step plans have no exposed screw holes

This beautiful Rustic X Console was built by Hillary from The Friendly Home.  I encourage you to take a second to stop over to The Friendly Home and read more about Hillary building this console, the finish she used, and the story behind those beautiful quilts!

Easier to Build Option: Farmhouse Console Table Plans

For beginner or novice builders, we have added a easy to build option for this plan, the Farmhouse Console Table plans.  It does NOT require pocket hole screws and is less expensive to build (but there is exposed screw holes).  There is also a video tutorial to help with the build.

Dimensions
rustic x bench plans dimensions diagram
Dimensions are shown above.

Preparation

Shopping List
  • 6 – 2x2 @ 8 feet long
  • 3 – 2x4 @ 8 feet long
  • 1 – 1x12 @ 12 feet long
  • 3 – 2x6 @ stud length or 8 feet
  • Corner hardware/decorative bolts
  • 1 1/4" and 2 1/2" pocket hole screws
  • 2 1/2" screws
Cut List
  • 12 – 2x2 @ 30”
  • 6 – 2x4 @ 28 1/2"
  • 2 – 1x12 @ 63 1/2"
  • 5 – 2x4 @ 11 1/4"
  • 2 – 2x2 @ 11 1/4"
  • 2 – 2x2 @ 22 1/2" (long point to short point, ends parallel, cut at 60 degrees off square)
  • 4 – 2x2 @ 11 1/4" (longest point to shortest point, long end cut at 60 degrees off square, short point cut at 30 degrees off square, angles are in same direction)
  • 3 – 2x6 @ 74 1/2"
Cutting Instructions

NOTE: If your saw does not cut 60 degrees off square, you will need to mark cuts with an angle square or compass/protractor and cut angles with circular saw or jigsaw. Practice this cut first on scraps!

Tools
Tape Measure
Speed Square
Pencil
Hammer
Hearing Protection
Kreg Jig
Drill
Miter Saw
Power Sander
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

First build two frames as shown in diagram.

Step 2

Then attach frames to shelves. NOTE: I recommend drilling 3/4" pocket holess with Kreg Jig around all sides of each shelf for attaching all shelf trim with 1 1/4" Pocket Hole screws later on.

Step 3

2x4 end supports need to be the same width as your 1x12 boards - expected to be 11 1/4" wide. Measure the width of your 1x12s and cut the 2x4 supports to match this width.

Attach to frames and shelves. For attaching to frames, use 1-1/2" pocket holes with 2-1/2" pocket hole screws.

Step 4

Add trim to the shelf.

Step 5

The X can be cut by just placing the uncut board alongside it's permanent position, and marking the overlap with a pencil, and then cutting the pencil lines with a circular saw or jigsaw.

First do the longer piece, then place inside the project, but don't attach yet.

The figure the smaller piece cuts and make those cuts.

Fit the smaller pieces in the project, and trace where they need to be joined to the larger piece.

Remove all pieces and attach the smaller pieces to the longer piece.

Then place the entire X inside the opening and attach.

Step 6

And then add the top. You can build top first with 1 1/2" pocket holes and 2 1/2" pocket hole screws and then attach to top through 2x4/2x2 aprons or just plank the top for a rustic look - it's up to you.

TIP: Just use your 2 1/2" pocket hole screws to attach the top so you don't have to go out and buy more 2 1/2" screws.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

ortho1121

Sat, 02/24/2018 - 11:57

To make the 60 degree cuts on your miter saw simply place a speed sqaure along the fence. This puts the wood at a 45 degree angle to start and then you just set your saw for 15 degrees. I use this when putting up picture framing on a wall going up a staircase where high angle cuts are needed.

newtodiy24

Mon, 02/26/2018 - 07:04

Does anyone know what the cost of this project comes out to be around?

jhoffbuhr

Sun, 03/04/2018 - 21:07

I have cut all the wood that was on the list, but my 2x2's (30 in ones) are not flush on the 2x4. Was I supposed to rip them down to a smaller size? I would appreciate all the help you can give.

RSQMonkeyII

Wed, 03/07/2018 - 12:59

Does anyone ever share their SKetchup Plans on here>  I want to convert this project to a coffee bar with a large blackboard and a shelf above.  Just checking before I build it from scratch.

Robb

tinajay

Wed, 04/03/2019 - 10:42

I believe in the linked post she said she just spray painted them black, but I have seen the black corner hardware on Amazon, don't know about the bolts

 

XOpTiMoX

Mon, 10/21/2019 - 11:12

The plan was awesome and I changed a few things (length and no center shelf) as Th looks we wanted didn’t require the length or center shelf, but The corner hardware and decorative bolts, where did you pick these up from? I can find any anywhere local. Thanks shins for the great plans!