OK now that I have used basic reading skills to find the correct forum …
Onto the Hemnes Cabinet:
On this project page Ana posted this picture talking about its color/finish.
A lot of the commenters were interested in plans. So I came up with this in Sketchup:
While probably not an exact duplicate, it comes fairly close. The overall dimensions are the same as on the "swedish" page, but a few parts are modified to use standard sizes of lumber to simplify construction. I would say that this project is advanced compared to many of the other plans on this site. A Kreg Jig is required, as well as a circular saw with a fine (40 tooth) blade.
Tomorrow I will post the shopping list, the cutlist, and step by step assembly guide.
EDIT:
Second part of plans are up on Flickr!
Dan K
Tue, 11/23/2010 - 19:32
Dan K
Wed, 11/24/2010 - 19:20
Cutlist:
2x2
4 @ 51¼
4 @ 15 7/8
4 @ 38
1x2
4 @ 15½
4 @ 41
1 @ 38
1 @ 3¾
1x4
2 @ 18 3/8
4 @ 17½ (Ripped to 3" wide)
4 @ 16 (Ripped to 3" wide)
1x6
3 @ 43¼
1 @ 43¼ (Ripped to 3¾" wide, use offcut for next piece)
1 @ 41 ¾x¾ Center Strip
1 @ 17 3/8 (Ripped to 3¾" wide, Center Divider)
¼ Ply or Beadboard
1 @ 47¼ x 39½
2 @ 17 ½ x 16¾
¾ Plywood
2 @ 15 7/8 x 45¾
1 @ 15 7/8 x 38
Dan K
Sat, 11/27/2010 - 11:47
Post Removed
Dan K
Mon, 11/29/2010 - 18:52
Post removed
Dan K
Mon, 12/06/2010 - 15:30
Second part of plans are now available
HERE
Cutlist and shopping list above have been updated
I welcome any comments, criticisims, problems, fan mail, etc...
Dan K
Mon, 01/10/2011 - 12:47
I've noticed a lot of people have looked at this and was curious if anyone had actually attempted to build it yet?
dananryan
Mon, 01/10/2011 - 19:56
Dan,
This is on my to do list, once I find the time. I bet if you submitted it as a new plan on Ana's website, lots of people would build it right away. It's a great plan!
Dan K
Tue, 01/11/2011 - 15:42
Thank you. I would love to submit it but I would have to condense it down to 10 steps, and that would would mean a lot more work. Writing the steps and taking all of the pictures take about 4 times as long as creating the sketchup itself. Of course Ana could make an exception.. *wink wink.. nudge nudge
ellison01
Wed, 01/12/2011 - 12:06
i would love this to be submitted, then i could put it on my to-do-list
Dan K
Thu, 01/13/2011 - 18:47
Allright... I bit the bullet and started condensing the directions down into 10 steps.
I'm about 80% done, still have to do a bit more photo editing and reworking of the instructions. There were a few glaring omissions that I will deal with in the finishing paragraph.
Barring any unforseen emergencies, it should be submitted by saturday.
Dan K
Sat, 01/15/2011 - 14:05
Plan is tweaked finished and posted, awaiting approval.
Dan K
Mon, 01/24/2011 - 20:13
It's finally posted! You can find it in the community plans section.
http://ana-white.com/2011/01/h.....binet.html