Can you build a box? What about three boxes? Then put some trim on the outside edges? Yes? Then you can build a storage bed like this one. The Storage Daybed is actually made up of three benches, very different benches than the Queen-Sized. These benches are much more simple. Thank you readers for the photos! Special thanks to Kara for sharing her amazing bed.
3 sheets of 3/4 inch plywood 3 - 1x4 @ 8 feet 6 - 1x2 @ 8 feet 6 - 1x12 @ 8 feet (optional drawers) 6 sets of side mount drawer slides, 18″ long, designed to fit in a 3/4″ gap (optional drawers)
Pieces to Frame 3Benches A) 6 – 3/4″ Plywood cut at 16″ X 39″ (Sides of Benches) B) 3 – 3/4″ Plywood cut at 23 1/2″ X 39″ (Bottoms of Benches) C) 3 – 3/4″ Plywood cut at 23 1/2″ X 12 1/2″ (Center Cubby Dividers) D) 3 – 3/4″ Plywood cut at 25 X 39″ (Top of the Benches) Trim Pieces for all three Benches E) 6 – 1×4 @ 25″ (Bottom Trim, Top 1 1/2″ upper corners mitered off at 45 degrees, see diagrams below) F) 6 – 1×2 @ 25″ (Top Trim, Ends mitered off at 45 degrees, see diagrams) G) 12 – 1×2 @ 14 3/4″ (Side Trim, ends mitered off at 45 degrees, see diagrams) Trim Pieces for the 2 Outer Benches, Exposed Edges H) 2 – 1×4 @ 40 1/2″ (Bottom Trim, top 1 1/2″ upper corners mitered off at 45 degrees, see diagrams) I) 2 – 1×2 @ 40 1/2″ (Top Trim, ends mitered off at 45 degrees, see diagrams) J) 4 – 1×2 @ 14 3/4 (Side Trim, ends mitered off at 45 degrees, see diagrams) K) 2 – 1x2s @ 11 3/4″ (Middle trim for the outside end benches) Optional Drawer Pieces L) 6 – 3/4″ Plywood cut at 20 1/4″ x 18 1/4″ (Drawer Bottoms) M) 6 – 1×12 @ 20 1/4″ (Backs of Drawers) N) 12 – 1×12 @ 19″ Sides of Drawers O) 6 – 1×12 @ 21 3/4″
See more details for cutting diagrams at the bottom of the page in the additional photos. Special thanks to Jen!
Begin by cutting all your boards. Check the diagrams for exact measurements on the trim pieces that need to be mitered out on the corners at 45 degree angles. Use 2″ nails unless otherwise directed. Always use glue. If you expect your bed to take heavy abuse (for example, used daily in a children’s room) you may wish to use screws. Screws will prevent wiggling and make the bed last longer, but are more difficult to build with. For the trim pieces, you may wish to cut as you go to guarantee the most perfect fit. If you are adding drawers, it is crucial that you build a perfectly square box for the drawers. Make certain that you cut the plywood square and that you check for square as you go. Your drawers will not slide properly if your drawers or the drawer box is not square. Learn how to check for square in the HOW-TO section.
My “trick” to getting the perfect drawer front is to mount the drawer box into the slides in the benches without the face. Then, with the faceless drawer pushed in, center the drawer face on the opening (and not the actual drawer). When you are happy with the gap around the drawer, nail the face to the sides and bottom of the drawer.