Finally, an Adirondack Chair that is easy to build and stylish and comfortable! This do it yourself project plan to build a DIY adirondack chair is simple, and easy. Inspired by polywood furniture, build your own affordable adirondack chair. Special thanks to Amy for sharing her photos.

Preparation
1 – 1×8, 8′ Long
4 – 1×4, 8′ Long
1 – 2×2, 8′ Long
1 – 1×3 8′ Long
1 1/4″ Screws (I would get pretty self tapping outdoor deck screws so that you don’t have to refinish your chair after you put it together)
2″ Screws
Wood Glue
2 – 1×8 @ 32 3/4″ (Stringers)
1 – 1×8 @ 21″ (Front)
5 – 1×4 @ 21″ (Seat Slats)
2 – 1×4 @ 20 3/4″ (Front Legs)
2 – 1×3 @ 24″ (Arm Supports)
5 – 1×4 @ 30 1/2″ (Back Slats)
1 – 1×3 @ 19 1/2″ (Top Back Trim)
1 – 1×4 @ 19 1/2″ (Bottom Apron Back)
1 – 2×2 @ 22 1/2” (Center Back Support)
2 – 1×4 @ 25 1/2″ (Arm Rests)
2 – 1×3 @ 6″ (Decorative Front Arm Supports)
Work on a clean, level surface. Use good, straight boards. On outdoor projects such as this one, it’s a good idea to paint your boards first (or invest in a tiny paint brush to get in between the cracks) so, sand and give your boards a nice paint job first. Remember, you can click diagrams for larger views. Pre-drill and countersink all of your screws. I would use a screw pattern so that your screws look nice and even (and you don’t have to finish the chair again after it’s assembled) Be safe and have fun!
Instructions
Step 1
Step 3
Step 7
ATTACHING THE BACK
Attach the back as shown above. This isn’t an exact science, I purposely choose to use a 1×3 for the arm supports and a 2×2 for the back support so that it would be super easy for
you to get the back to line up just right with the seat and arm supports. You may want to enlist your neighbors assistance.
Comments
In reply to Class auction project by LianaBanana
Ana White
Mon, 08/03/2015 - 10:30
We can't wait to see what
We can't wait to see what they do!
charmom2015
Tue, 09/08/2015 - 10:44
Question on measurement of back width
Hi Ana, I was preparing to use this plan and I noticed that you are showing the horizontal piece on the chair back (top and bottom) as 19 1/2 ". You are showing 5 back slats from 1x4 lumber and 1/2" spacing between each back slat. I'm adding the 5 back slats to get 20" and then add 3 spaces at 1/2" each for a total of 21 1/2". Doesn't that mean that the 19 1/2" measurement on the diagram is wrong? Or am I missing something?
Ana White Admin
Wed, 09/09/2015 - 11:51
measurements
A 1 x 4 actually measures 3/4" x 3 1/2", check this out for actual lumber measurements http://mistupid.com/homeimpr/lumber.htm
Hope this helps!
carlaz92
Tue, 08/16/2016 - 11:00
Ana, I'm new to your site, but not to your builds! how do I ask
Hi Ana, I was wondering where people can request you figuring out a new project to build. I want to build an adirondack set for my sister and hubby. They are building a new home, but it is very modern. I found a picture I was hoping you could do plans for the set. table as well.
Joshua_Manning
Sat, 04/22/2017 - 19:07
I think this should be
I think this should be renamed "Ana-rondack chair"
Clang
Sat, 05/25/2019 - 05:17
Where is the must see video…
Where is the must see video for the kids project? I am almost ready to build and want to be I get it right the first time. Thanks in advance for your help.
tnmillernc
Fri, 11/22/2019 - 11:56
Adirondack Chair Question
I would like to build your adirondack chairs but wanted to know if the dimensions for the lumber in your shopping list is actual or nominal? Your builds are beautiful, functional, and easy for newbies to try. Thank you!!!
kkavanaugh56
Thu, 02/20/2020 - 06:35
Hi, like the plans and…
Hi, like the plans and layout, only comment is the lack of specificity on screw locations. Thanks
Kurt
tomgru
Thu, 05/28/2020 - 19:29
I have used this plan to…
I have used this plan to make a bunch of chairs!
njohnson5303
Sun, 07/19/2020 - 18:52
Knock off wood?
New here. This is going to be my first project. May be a dumb question, but what does "knock off wood" mean? Can I use any type of wood?