1. Home
  2. Plan Catalog

Rustic X End Table

|save this plan
Submitted by Ana White on Thu, 08/15/2019 - 00:03
Difficulty
Intermediate
| Print this plan

Build your own end tables!  These gorgeous rustic style end tables are built from 2x4s and lumber.  We love the large size and the open bottom shelf. Stain or paint any color. Our beginner friendly plans make it easy with step by step diagrams, shopping list and cut list.  

Also in this Collection: Rustic X Console Table, Rustic X Coffee Table and Rustic X Bench Plans

Collections
Rustic X Collection
rustic x end table plans

Rustic X Living Room Table Collection

This end table is part of a collection of living room furniture that you can build. All the plans are available for free for your use.

It all started with this beautiful X Console Table, built by Hillary from The Friendly Home.

And then we added this beautiful Rustic X Coffee Table, also built by Hillary.

Now, Hillary used up her scraps and built X End Tables!

 

DIY Wood Finish

Hillary used a steel wool and vinegar solution to age her end table. Want the same finish? Get the step by step tutorial here.

Dimensions
rustic x end table plans
Dimensions shown above.

Preparation

Shopping List
  • 2 - 2x4 @ 8 feet long
  • 1 - 1x12 @ 3 feet long
  • 2 - 2x2 @ 8 feet long
  • 2 - 2x6 @ 8 feet long corner bracket hardware decorative bolts
  • 2 1/2" and 1 1/4" Pocket Hole screws
  • wood glue
Cut List
  • 8 - 2X4 @ 22 1/2" - Legs
  • 4 - 2X2 @ 16" - Trim
  • 2 - 1X12 @ 16" - Bottom shelf
  • 2 - 2X2 @ 26 1/2" (LONG POINT TO SHORT POINT, ENDS ARE PARALLEL, 50 DEGREES OFF SQUARE) *
  • 4 - 2x2 @ 13 1/4" (Longest edge, one end cut at 50 degrees off square, other end cut at 10 degrees off square, see diagram) *
  • 5 - 2x6 @ 27" - Top

*You may wish to trace and cut these in place

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Miter Saw
Power Sander
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

Start by building two ends as depicted in diagrams. You can also attach with countersunk 2 1/2" screws and glue.

NOTE: Yellow board width should be 22 1/2"

Step 2

Next attach the 2x2 sides.

Step 3

And then build your bottom shelf and attach to bottom of console.

Step 4

Now it's time to fit your cross braces. A standard miter saw should cut a 50 degree angle off square. If not, you will need to mark it with a square (remember 50 degrees is off square, so that means the angle off the board edge would be 40 degrees.

Another trick is to just hold the board in place, mark the angles, and cut. These aren't support boards or anything like that, so some glue and a few nails or countersunk screws from top/bottom will do the trick.

TIP: We recommend building the entire X first, the attaching the complete X inside the end table.

Step 5

The smaller X pieces can be cut to fit.  Attach with a 1-1/2" pocket hole and 2-1/2" pocket hole screw, one screw per joint.

Step 6

Next build your top ... and attach in place with countersunk 2 1/2" screws. If you have the PH screws on hand, I just use a few of those!

Step 7

And then add the decorative hardware!

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Project Type
Side and End Table Plans
Room
living room
Style
Farmhouse Furniture

Comments

pruittmac

Tue, 10/18/2016 - 07:24

I am planning on making one of these tables today. Wondering about how long it takes just to build it? TIA!!!

Jaelane

Fri, 11/18/2016 - 15:15

you said you have a kreg jr. It when I go to look for one there are so many different kinds. Kreg R3 jr , R4 ect. I'm not sure which one to buy. What exact one do you have? 

Brian Famous

Thu, 01/25/2018 - 12:57

You can actually make them yourself fairly easily.  All it takes is a piece of flat bar steel, a way to cut the steel (I use a grinder with a cut off wheel, but a hacksaw would work too), a drill with a good drill bit (for drilling the bolt holes), a vise, a hammer, and some spray paint.

If you get a longer piece of steel than you need, it's easier to bend because you get more leverage on it.  To make it even easier, you can use a torch to heat the steel at the point you want to bend it.

MacGyver

Mon, 01/22/2018 - 16:01

I'm new to the world of woodworking and trying to figure out the easiest way to adjust the measurements but still make it look the same.

Brian Famous

Tue, 01/23/2018 - 07:41

If you are trying to change the measurements, can you provide the new final dimensions (height, width, and depth) you are trying to achieve?  Knowing those dimensions would be the first step in determining how the measurements need to be changed.