Community Brag Posts

Thank you for the plans!

I used the following for the wheels,  they are AMAZING and dont require you to tear apart any pulleys. These wheels have bearings in them too,  which make them slide super quiet and smooth!

http://www.homedepot.com/p/Barton-Kramer-1-1-2-in-Precision-Bearing-Stainless-Steel-Wheel-2-Pack-43/205649620

Tony S.

A few months ago we decided to build ourselves a new table based on the Farmhouse Table plans. We knew we wanted to make the table out of some red oak that I had gotten for free, so we would deviate from the plans a bit. Long story short, I deviated from the plans _quite_ a bit. We had planned to make the table essentially with free materials, but that changed when I spent several days squaring up the rough stock I had been given. I also joined a crowned plank in the center of the table-top...big mistake. After glueing, screwing, and sanding, I realized there would be no way to get the crown out of the top. So...the first table-top became the bench cover and the other half is going to be used for a computer desk in another room. After a trip to the local lumber yard, I had about $220 worth of red oak: 4 1x4x14ft planks for the legs and 7 1x6x6ft planks for the table top.

I began by cutting the 14 ft. 1x4's to length and then joining them with lots of glue and clamps to form the legs. Next I set up the table saw to notch out the tops of the legs to receive the box. I prefer this method over using a circular saw or jig-saw. Picked up my wood-chisel to clean things up and then sanded, scraped using a card scraper (I would highly recommend a scraper for the smooth finish and handcrafted feel the tool provides), applied two coats of stain, and finished with two coats of wipe on poly.

I followed Ana's plans to construct the 2x4 base, modifying it to fit the size of my table and the specific overhang I sought. I also simply used 2x4 scraps to span the width of the box, and then Kreg jigged them to the box and table-top for support.

I joined the table-top planks using a Kreg Jig and glue. Lots of sanding and scraping again, and then I flipped the top, attached the box, and attached the legs. I used more of the 1x4's for the skirts to hide the 2x4 box.

We decided that we wanted to build a built-in bench for storage instead of a free standing one to accompany the table. I followed the plan at the following site, modifying it as necessary to match the length of our table. I also only built the bench and not the wall unit (http://www.thisoldhouse.com/toh/how-to/intro/0,,20301255,00.html). My mistake with the first table-top ended up being a blessing of sorts when we were looking for a sturdy bench-top.

All in all, we love it! It took a good deal of time to finish the table—in part because I'm a horrible perfectionist. The bench, on the other hand, was finished in a day's work.

The table is constructed entirely out of red oak. The bench-top is also red oak. The bench is birch plywood and pine.

Total cost for table: $220 for wood; we already had all other supplies
Bench: $25; again, we already had most of the materials needed.

We revised the design a bit to make it fit in our space. We also made room for our dog food bin at the bottom

My entry into the IG Builders Challenge. Modified the Ana White Bailey Console a few ways. Instead of 2 large drawers, I installed 2 doors on each end, with 2 drawers in the middle. Century old barn wood used throughout. The legs are reclaimed oak floor joists, front stretchers are oak, rear stretchers are poplar. Heart pine planks users as door and drawers fronts. Heart pine front the same barn used as the top as well. Barnwood skins used on each end and the middle of the backside. Reclaimed shutters were used on the door compartment bottoms, and the rear.  I may eventually add a lower shelf with some of the leftover poplar and barnwood skins at a later date. 

This bed has been a true labour of love over the last few months!

I made all cuts with a hand saw, and mainly used a kreg jig to assemble the bed.

The 'insert' in the headboard is made from macrocarpa window trim and tongue-and-groove panelling, which was leftover from when my parents built their house. The rest I bought from a local supplier as rough sawn timber, which I got dressed by a woodworking guy who lives nearby. Had I bought all the timber I used, the cost would have been closer to $400.

I didn't add the moulding that is included in the plan - it's just my preference.

It took a bit of work to convert Ana's plans into metric measurements, but I got there in the end! I love my bed

I was recently divorced and decided to fully transform my bedroom. It's not quite done in this picture - but the bed is! This is Ana's King farmbed, and it's amazing.

I decided to do some modifications to the original plans to make it more like the Pottery Barn original. I made the legs 4x4s like the original, as well as the horizontal bases of the legs. The major change that this entailed was in the bottom shelf. I notched the edges of the 1x12 so that it would fit flush, then connected it to the legs with pocket screws. The lowered ledge on the table top is two 2x4s on the bottom, a 2x4 on the front and back, and a 2x6 cut to size for the ends. I then attached it using pocket screws on the front, and just 2.5 inch screws from the back. The rest is pretty much the same as the plans. For the back of the hutch, I used 1x4 carsiding to give it a more finished look. It only cost a couple cents more for each 8 foot piece.

Thanks to our daughter who gave me plans from Pintrest for the popular locker. This is my first project in a long time. It has been followed by a few projects which have been inspired by plans or skills from the site.

Thanks

I started woodworking about 6 month ago and I love it! 

I made our kitchen table and nightstands.

This was a real test! The drawers took as long as the frame, if not longer.

It's all worth it when it turns out this good though!

Thank you for all the wonderful plans, my wife practially has all the furniture in our house in line to built by me. 

I moved into a new house and needed a new chicken coop. I am retired and not a woodworker but these plans were easy to build. Thanks Ana.

My niece is here for the summer! We needed a guest bed fast, that didn't take up an entire room! She chose this day bed!

Her bed is in the computer room, so there isn't enough room for a twin size bed. I modified the plans to fit a standard crib mattress. Now, when she isn't using the day bed, it doubles as a lounging spot to read. It is soooo cute!

For the storage baskets, I cut shipping boxes to size and mod podged fabric to them, and added some cute little knobs.

The Basic Process - Triple Bunk Bed Plans

More info on these Triple Bunk Bed Plans on my blog: http://myhomedonemyway.blogspot.com/2013/03/triple-bunk-bed-finished.ht…)

1. Build the Bed Frames: (I will explain the process for one bed...do it three times if you want three beds)

2. Add Side Supports: ( Also do this step three times for three beds. We did it later but would be easier to do now)

3. Add Roll Guard: (do twice...once for each top bunk. We did this later but can be done now)

4. Build Ladder:

5. Paint desired color (you don't have to paint the sides that will be screwed into the wall).

6. Install into the wall in desired bedroom

7. Add Supports (do three times for three beds)

8. Add Plywood (do three times for three beds) 9. Finish

Built my daughter the day bed, and my son needed his own bed. But with a 2 bedroom house they have to share a room for now. So I seen the loft bed and well this is what I came up with. I stained it cherry, and routed the edges to give it a little touch.