1. Home

Community Brag Posts

Treehouse Adventure Bed (Alternate Beach Hut Bed)

I was looking for something to build for a fundraiser this year and found the Beach Hut Bed plans. I liked the idea of a little house inside a kids room but I wanted to do something a little more rustic. here's what I came up with!!!

The shopping list and cut list is pretty much the same. However, I only used one 1x3 and needed to buy 4 extra 1x4s. I lowered the bed deck about a foot and left half of the walls open for easy parent access. I sorta just winged it as I went. Turened out pretty neat!!!

Built from Plan(s)
Beach Hut Bed
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Roof: Valspar Exterior latex paint+primer. Main structure: burned with torch, wipe on poly, high gloss
Recommended Skill Level
Intermediate

Comments

Concrete top

I changed up the legs because I had a beautiful piece of reclaimed wood I've been looking to use.  I did use these plans for the concrete top and it turned out great!  Just followed all of her advice.  It's very smooth, almost feels like soft cotton, with only tiny bubbles.  Thanks for the great plans!

Built from Plan(s)
X Base Outdoor Concrete Table and Bench Set
Estimated Cost
$20 for the wood and $25 for the concrete top
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
Minwax Weathered Oak
Recommended Skill Level
Starter Project

Ultimate Roll Away Workbench with Miter Saw Stand

Submitted by mbaylis on Mon, 10/18/2021 - 14:05

So nice and tidy in the garage now!

Comments

Factory Cart: How Low can you go?

Submitted by chjaway2 on Wed, 03/23/2011 - 08:15

The Factory cart was really easy to put together.

I used a pocket-hole jig to eliminate any screw heads on the exterior.
The wood I had was already distressed somewhat, but I figured that would add to the 'old' look when ultimately completed.
The most difficult part of this project was finding casters that I liked and that I could afford (those suckers are expensive!)  I'm still not 100% sold on the ones I purchased, but will keep my eyes open when out & about for replacements!
The plans posted on Ana-White.com could NOT have been easier to follow.
However, I should like to stress that this coffee table is EXTREMELY low to the ground.  One of the first lines on the plan page reads:  "This coffee table sits lower than traditional coffee tables." = understatement of the year!  (my fault, I should have compared the posted dimensions with an existing coffee table to get an idea before hand) 

The plans will make a awesome factory cart height factory cart, but a nearly-uncomfortable height coffee table (As is).  In the attached photo, you'll note a foot-rest in the upper left corner as compared to the finished factory cart.
 --again, the build was super easy & a LOT of fun because I intended the finish to look worn, I didn't have worry about scratching up the wood during the build.  In fact, the kids are looking forward to helping me distress it later!  I'll just have to increase the height of the sides to make it usable as a coffee table in our home.

Built from Plan(s)
Factory Cart Coffee Table
Estimated Cost
$40
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
(Will) Paint, distress & stain
Recommended Skill Level
Beginner

Wide Cabin Dresser

Submitted by mebohn on Fri, 06/07/2013 - 05:46

I This project is definitely the most difficult I've ever built. I've done lot of drawer slides before, but for some reason this one was the hardest. I think the culprit was squaring, which was mysterious to me bc I'm careful to take a square constantly. Could've been bowed boards, too. But, after some patience and forcing the boards to do what the should, it worked. I did rip down 2x4's for strength b/c our stores do not carry the upgraded 2x2's and furring strips would just not have been strong enough for a dresser. My son is very happy to finally have a place for his clothes. Thanks Ana for these plans!

Built from Plan(s)
Wide Dresser with Open Bottom Shelf - Cabin Collection
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
Steel Wool and vinegar, Rustoleum ultimate poly in matte
Recommended Skill Level
Advanced

Comments

spiceylg

Fri, 06/07/2013 - 08:26

Your efforts were worth it. This came out beautiful. Looks professional.

Benchright Coffee Table

This was one of my first projects. I made it for my daughter who was moving to a new apartment and wanted to replace her college coffee table. It was fairly easy other than keeping everything square so the drawers worked correctly. I finished it with Rust-Oleum Ebony stain and Minwax Satin Poly (3 coats). All the hardware and lumber came from the Orange big box store

Built from Plan(s)
Classic Wood Coffee Table with Two Drawers and Shelf
Estimated Cost
$100
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Rust Oleum Ebony Stain
Minwax Satin Poly
Recommended Skill Level
Intermediate

Kids table and benches

Submitted by dhoop31 on Sun, 10/15/2017 - 06:03

Built this with matching benches that will store underneath the table completely.  Thanks for the great ideas!!

Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
none
Recommended Skill Level
Beginner

Left Coast Adirondack Chairs

Submitted by Reader Submission (not verified) on Tue, 10/26/2021 - 16:24

Thank you for the plans!

Comments

Photo Gallery Ledges

I was always a fan of the gallery wall, but not having a big empty space in any of my main rooms I didn't think I could have one.  However, once I finally got my stairway and upper hallway painted, I realized the wall needed something and the gallery ledges would be perfect!  Save the old plaster walls from being bashed with picture hanging nails too!
I build them out've 1x3's and a small 1/4 round for the front edge instead of a 1x2.
I made 2 3' long and 2 4' long and staggered them on the walls, as the walls are at a slight angle to each other.
I decided to paint them the same colour as the walls so they would blend in and the picture frames would stand out.  All the frames are varying wood stain colours that go with the trim in the house.

I love having a place to put all the pictures I never find time to put up!

Built from Plan(s)
Gallery Ledge Shelves
Estimated Cost
$24 for all 4
Estimated Time Investment
An Hour or Two (0-2 Hours)
Finish Used
Paint. Home Hardware 'Burnt Sugar'
Recommended Skill Level
Starter Project

Farmhouse Bunkbeds with Stairs

Submitted by Yodannos on Sun, 06/09/2013 - 13:19

We have a rental unit and decided to fill one room with 2 sets of bunk beds. One is a twin over a full. The other is a full over full. Due to a duct running through one corner, and limited amount of space, I decided to build a set of stairs on the 17" gap. I used the simple bunk bed plans, but modified it to the style of the farmhouse. Also, I changed several of the heights of the foot/head boards. The full over full will have a ladder coming off the end and is in progress.

Built from Plan(s)
Farmhouse Bed (Full Size)
Simple Bunk Bed Plans (Twin over Full)
Estimated Cost
$450
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Minwax Ebony Stain. Satin Polyeurethene.
Recommended Skill Level
Intermediate

Farmhouse Nightstand

Submitted by RenoRustic on Tue, 05/12/2015 - 10:17

I built this nightstand when my wife and I purchased a new bed. We had to rearrange the bedroom and as such, I no longer had a desk or table on my side of the bed. I wanted something "country" style and after searching through several different plans I found a brag post that fit exactly what I was looking for. Well, technically, I found the original Farmhouse Bedside Table plans and modified them to fit what I needed. It wasn't until after I completed the project that I realized there was a "Mini" version as well. What can I say, I'm not that great as using search. I actually built this over a year ago at this point, and it was the second project I ever built. I learned quite a bit on this project, including the fact your project will only come out as good as your lumber selection! This build actually created my addiction for DIY and woodworking. Thank you Ana!

Blog Link
Farmhouse Nightstand
Built from Plan(s)
Mini Farmhouse Bedside Table Plans
Estimated Cost
$40
Estimated Time Investment
Day Project (6-9 Hours)
Finish Used
I used Minwax Special Walnut for the entire project, then painted the base and drawer Behr white (their basic white off the shelf, I didn't have the paint mixed) in semi-gloss. I antiqued everything for a more rustic look.
Recommended Skill Level
Beginner

Comments

Harvest Table DIY

Submitted by Reader Submission (not verified) on Mon, 10/23/2017 - 10:18

 

Submitted by Valeria Green -

My husband built this table and bench for my son and his wife. He is presently building another by request for a young couple.

Built from Plan(s)
Fancy X Farmhouse Table
Recommended Skill Level
Intermediate

Comments

amberfro

Thu, 10/25/2018 - 11:01

I love the use of the 4x4s instead of the 1 and 2 x 4s. How did he attach the 4x4  used for the width to the 4x4s for the side braces and height? Thanks in advance

Farm table

Submitted by Reader Submission (not verified) on Fri, 11/05/2021 - 14:15

I had just had a bad experience with a furniture company that sent me the wrong table after I had waited for many weeks for it. I was so exasperated I decided I would make my own from your instructions. I am a 62 yo woman and I had a blast making it. I am now planning to make a bedroom set next!!!

Built from Plan(s)
Farmhouse Table - Updated Pocket Hole Plans

Comments

Craft Table Build

Submitted by cathytn2 on Thu, 03/31/2011 - 05:28

I emailed my husband the plans for this desk on a Friday night and said we HAVE to make this desk this weekend.  I can't believe he actually went for it!  Well it turned into about 3 weekends and some nights of painting.  We also had some issues getting straight and square plywood and boards with knots in them.  He also added some extra holes in the sides for me to adjust the shelves.  We used an oil based white paint to finish the desk and looks nice and clean and shiny.  I can't wait to get started on our next project!  Please check out my blog for more details and photos and information on materials used, etc. (kitcats-studio.blogspot.com/2011/craft-table-made-from-plans.html
PS - {I had one more coat of paint on the drawers to finish so ignore the bare fronts of the drawers.}

Blog Link
Craft Table Made From Plans
Built from Plan(s)
Cubby Bookcases Modular Office Collection
Craft Table Top For The Modular Collection
Estimated Cost
$150
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
We primed everything using Zissner and then used an oil based white paint (about $15/gallon) from Lowe's for the finish. The trick to doing this is a WELL ventilated area, and a good brush. Although we're kind of lazy about cleaning up from oil based paint (it's a chore) so we got a medium cost brush (about $5) and threw it away when we were done with it. I used general handles from Lowes and the color on the inside of the drawers is Valspar Turquoise Tint 5006-10B.
Recommended Skill Level
Beginner

Farmhouse Table and benches

This is the first furniture building project that my husband and I have completed. It took us about 5 weekends to complete it- including finishing.

We started with the benches as recommended in some of the comments and ended up buying a pocket hole jig and redoing the tops of the benches before completing the table.

The stain is Minwax Red Chestnut and there are three coats of Minwax Fast Drying Polyurethane on it. We're so happy with it and can't wait to start the next project!

Built from Plan(s)
Farmhouse Table - No Pocket Holes Plan
Farmhouse Bench - No Pocket Holes Version
Estimated Cost
about $200
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Minwax Red Chestnut stain- one coat
Minway Fast Drying Polyurethane in Semi Gloss
Recommended Skill Level
Beginner

2x4 Rustic Outdoor Bench

Submitted by Reader Submission (not verified) on Thu, 11/09/2017 - 09:46

Submitted by Carla Santiago on Facebook - 

 

We did a bench, I got your plans off Pinterest. We just put a slight slant to the back and we love it. Thanks for the great plans.

Built from Plan(s)
Modern Park Bench
Recommended Skill Level
Beginner

Great Book Caddy / Wine Rack / Side Table..fun project!

Submitted by Don Ellery on Sat, 05/16/2015 - 17:12

Great project plans from Ana and of course, LadyGoats. Thank You!

Wood: Pine (similar cut list to what was in the plans)

Time to complete: Approx 4 hours.

Joints: 3/4 inch pocket holes with 1 1/4 inch pocket hole screws and glue. Love my Kreg Jig.

Stain: Varathane Espresso color, two applications.

Fun morning project! This table/shelf can be used for so many things. Once the two pieces are secured together it is very solid. The bottom was made from Ana's x book caddy plan and the shelf was modified from LadyGoats booksellers plan.

Hope you all like it!

Don

Built from Plan(s)
DIY Bookseller Shelf - Featuring Lady Goats
X Book Caddy
Estimated Cost
$80, approx. Depends on what type of wood you use.
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
Espresso color varathane, single application, foam brush and rubbed with rag to finish.
Recommended Skill Level
Beginner

Comments

Chunky Media cabinet

Submitted by redhead_61 on Tue, 12/05/2017 - 22:43

This was loosely based on one of the media cabinets on this site.  I built it to fit this spot exactly and used many of the same design elements as in the Leighton media Suite I built several years ago.  One thing I want to mention I did with this design that is a FABULOUS idea in all media units.  Inset the back of your lower section.  I hate not being able to run the top of my "counter" flush with the wall because the back of my unit or bookcase is running into all the plugs in the outlet.  I left a little larger of an overhang than I normally wood to clear the baseboards and I inset the backing of this peice about and inch inward to leave lots of room for all the chords to just hang there but be hidden.  They are much more accessible and now the top of my unit is flush to the wall.  

Estimated Cost
$80
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Acrylic hard finish white paint.
Recommended Skill Level
Intermediate