Ana's Adirondack Chair

Submitted by Ana White on Tue, 05/18/2010 - 12:27
Difficulty
Beginner
| Print this plan

Finally, an Adirondack Chair that is easy to build and stylish and comfortable! This do it yourself project plan to build a DIY adirondack chair is simple, and easy. Inspired by polywood furniture, build your own affordable adirondack chair. Special thanks to Amy for sharing her photos.

Adirondack Chairs
Ana's Adirondack Chair

Pin For Later! 

Adirondack Chairs

Dimensions
Adirondack Plans
37 1/2" x 30 5/8" x 19 1/2"

Preparation

Shopping List

1 – 1×8, 8′ Long 4 – 1×4, 8′ Long 1 – 2×2, 8′ Long 1 – 1×3 8′ Long 1 1/4″ Screws (I would get pretty self tapping outdoor deck screws so that you don’t have to refinish your chair after you put it together) 2″ Screws Wood Glue

Common Materials
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Cut List

2 – 1×8 @ 32 3/4″ (Stringers) 1 – 1×8 @ 21″ (Front) 5 – 1×4 @ 21″ (Seat Slats) 2 – 1×4 @ 20 3/4″ (Front Legs) 2 – 1×3 @ 24″ (Arm Supports) 5 – 1×4 @ 30 1/2″ (Back Slats) 1 – 1×3 @ 19 1/2″ (Top Back Trim) 1 – 1×4 @ 19 1/2″ (Bottom Apron Back) 1 – 2×2 @ 22 1/2” (Center Back Support) 2 – 1×4 @ 25 1/2″ (Arm Rests) 2 – 1×3 @ 6″ (Decorative Front Arm Supports)

Tools
Tape Measure
Speed Square
Pencil
Hammer
Safety Glasses
Hearing Protection
Drill
Circular Saw
Miter Saw
Level
General Instructions

Work on a clean, level surface. Use good, straight boards. On outdoor projects such as this one, it’s a good idea to paint your boards first (or invest in a tiny paint brush to get in between the cracks) so, sand and give your boards a nice paint job first. Remember, you can click diagrams for larger views. Pre-drill and countersink all of your screws. I would use a screw pattern so that your screws look nice and even (and you don’t have to finish the chair again after it’s assembled) Be safe and have fun!

Instructions

Step 1

CUT YOUR STRINGERS
From the 1×8 stringers listed in the cut list, cut your stringers as shown above. You may wish to create a pattern and then copy the pattern for both sides. This is the trickiest step. If you can do this, you’ve got it made!

Step 2

FRONT APRON
Attach your front apron with 2″ screws and glue as shown above.

Step 3

SEAT SLATS
Lay your seat slats as shown above, starting with the first flat seat slat. Leave a 1/2″ gap between the slats. Screw down with 2″ screws and glue.

Step 4

FRONT LEGS
Use 1 1/4″ screws and glue to attach the front legs as shown above.

Step 5

Step 6

BACK
Build the back as shown above.

Step 7

ATTACHING THE BACK
Attach the back as shown above. This isn’t an exact science, I purposely choose to use a 1×3 for the arm supports and a 2×2 for the back support so that it would be super easy for
you to get the back to line up just right with the seat and arm supports. You may want to enlist your neighbors assistance.

Step 8

ARMS & SUPPORTS
Attach your arms with 2″ screws and glue. Then attach the arm supports.

Finishing Instructions
Preparation Instructions
You should be done! This chair will fit a standard cushion, sized anywhere from 18×18 to 20×20. Can’t wait to see your photos!

Comments

teamshield (not verified)

Tue, 05/18/2010 - 13:31

Now the only question is should I paint them in all different colors so everyone in the family can have their own shade?

Catherine Hans… (not verified)

Tue, 05/18/2010 - 14:06

Great plan Ana! Remember, don't knock yourself out with a killer schedule. We will all be waiting whenever you can get to them! (you have some serious great Karma heading your way after all your generosity - remember us when you are rich and famous! lol)

Heather (not verified)

Tue, 05/18/2010 - 14:10

sounds good to me!! I'd rather have plans than brags any day anyway. :) The chair looks amazing!!!

Ange (not verified)

Tue, 05/18/2010 - 14:13

Thank you so much! But we do recognize your job first is wife then mother....then furniture planner :) You're the best.

Cheryl (not verified)

Tue, 05/18/2010 - 14:44

Thank you for posting this, Ana!!! I was going to buy one of these one day, but now I just might build one!

Tanjia (not verified)

Tue, 05/18/2010 - 15:39

If you're 25 plans behind on posting then I'm 100 plans behind on building!! I've only finished the bigger kids picnic table and I'm working on the modern outdoor table. Wish I could build one thing every day! I have to keep reminding myself it's okay to take it one project at a time.

Leslie (not verified)

Tue, 05/18/2010 - 16:13

Ange had it right, Ana! Wife and mom first - everything else comes after that. You rock! The fact that you do all this with no cost for the finished plans totally blows my crazy mind.

I'm thinking teal and red chairs myself! I'm loving this plan.

Thanks again!

Waner Family (not verified)

Tue, 05/18/2010 - 16:34

You're amazing! I just found you three days ago and have stayed up until 3am each morning obsessing over your site! We are moving to a new town in three weeks, and I CANNOT WAIT to start building once we get there! You are such an inspiration to women (and men) everywhere! Thank you for giving so freely of yourself, your plans, your time, and your inspiration!!

slp higgins (not verified)

Thu, 05/26/2011 - 20:24

I think anyone who has ever come across Ana's site has had this happen to them.

The funny thing is, even 1.5+ years later, I still find myself obsessed, inspired and spend hours browsing.

Sophia Almejo (not verified)

Tue, 05/18/2010 - 17:01

Ana, you know that I love everything you do. I think you are a very talented woman...please odn't worry about getting the plans up right away we will manage...we understand that you have a family...once again thank you Ana.

Jen (not verified)

Tue, 05/18/2010 - 17:51

Just a suggestion, but I love polls. How about a poll with, say, 20 plans you're considering doing (then you can keep a few juicy ones to yourself) and which ones we want the most? Then you'd have a little guidance as to what to do first. Because maybe we're all just absolutely dying for five of those plans for next week, and then you could take a vacation or a staycation at least :) I'd also love a poll on people's favorite ways to finish different kinds of wood. Polls are fun for us and less work for you. :)

Jen (not verified)

Tue, 05/18/2010 - 18:14

Was reading the "details" on that other place that makes chairs like these (can't remember name-Poverty Shack?). Care instructions are:
* Dust often using a soft, dry cloth.
* Protect from direct sunlight and extreme temperatures.
* Blot spills immediately with a clean, damp cloth.

I'm sure glad I'm building and finishing my own Ana White chair instead. Dust! Did they say to dust it? My children will be dripping smores on these babies! And protect from direct sunlight? I will be placing mine in direct sunlight to enjoy. I'll enjoy it even more knowing I can build four for the price of their one. Thanks Ana!!!

Melissa (not verified)

Tue, 05/18/2010 - 18:21

I love all of your plans. We are getting a new house soon and I can't wait to begin on some great projects using your ideas. Can you do a corner hutch design? I love these and really want one in our new home.

pogonip (not verified)

Tue, 05/18/2010 - 19:50

Making the Ana Adirondack chair just moved to the top of my summer to-do list! Now my only problem is what color to paint it--so guess I'll have to make one is each color :) Thanks a gazillion for this one, Ana!

Urban Dragon (not verified)

Wed, 05/19/2010 - 06:01

Thanks Ana!! Don't stress yourself out though. I have been down that road myself. I used to offer a freebie a day on my blog (Digital Scrapbooking Kits is what I offered). I ended up stopping because it was too much for my family. That won't happen to you I am sure because you are much more energetic than I am but just be careful. I for one would rather have some plans from you than no plans from you. Thanks again :)

Kristi (not verified)

Thu, 05/20/2010 - 02:01

In the nicest possible non-weird way, I love you. And your site. Five picnic tables later (the MOST appreciated birthday gift I have ever given) I'm ready to make something for us. Thank you!

And you take your time- Mom first, then all the other stuff. We'll be here waiting patiently. Okay, not so patiently because we adore what you do, but we'll be here waiting.

Jaime (not verified)

Thu, 05/20/2010 - 12:54

Thanks for the plans! I now have 2 adult sized chairs and 2 kiddo sized chairs to build. Hubby keeps telling me we don't have the tools, and while he may be right, I WILL build me a chair just me and my hand saw! I CAN do it! (it just might not look quite as pretty!

Loni (not verified)

Thu, 05/20/2010 - 15:57

Thank you thank you thank you! Ana, You are so freaking awesome. What you do for us is not only showing us a method for building our own furniture. You are also inspiring us, motivating us, making dreams come true, and most importantly (to me anyways) you're boosting our self esteems. Thank you a hundred times.

carie (not verified)

Fri, 05/21/2010 - 17:28

Hi Ana, I just bought cut and painted my wood today! I'm super excited to put it all together tomorrow :) I had a little problem with the shopping list but I am wondering if it is my mistake because I doubled the list (except for the 2x2) to make 2 chairs. I ended up being short about 106 inches of 1x4, I ran out just before I cut the arm rests at 25 1/2". I'm thinking that maybe this happened because I cut all my boards of the same length at the same time so my scrap amount was different, I don't know. I just ran back to Home Depot and bought a 10 footer - no biggie but I thought you'd like to know.

msk171 (not verified)

Sat, 06/02/2012 - 19:02

The 1x4's had me a little confused when I came up short so I did the math...here are the cuts so they fit on each board. Yes, you still only need 4 --1x4, 8' long:

Board 1: 21",21",30 1/2",19 1/2"
Board 2: 21", 21", 25 1/2 ", 25 1/2"
Board 3: 21", 20 3/4", 20 3/4", 30 1/2"
Board 4: 30 1/2", 30 1/2", 30 1/2"

Drama Queens (not verified)

Sun, 05/23/2010 - 12:24

I am new to your site and LOVE this plan! I have all my boards cut and they are finishing drying after painting and priming as I speak! I can't wait to put it all together! I have never built anything really--besides helping my dad when I was a kid. I used my hubby's radial arm saw for all of the cuts--worked but not the best I'm sure--and only spent $1.50 as we had most of the wood and paint. Thanks so much for a fun project, can't wait to do more!

Drama Queens (not verified)

Mon, 05/24/2010 - 09:11

OK--so my question is--I was screwing the 2x2 back support on using the 2" screws-predrilled my holes--and SOMEHOW I went all the way through the back slats! The 1 5/8 screws I have are too short, the 2" screws are too long--what do I DO???

Ana White (not verified)

Mon, 05/24/2010 - 10:28

It sounds like you may have a deep countersink bit. What I would do is fasten from the front face of the back slats into the 2x2, instead of from the back.

Drama Queens (not verified)

Tue, 05/25/2010 - 06:05

thanks--I actually wound up improvising and cut 1/2" slats into small squares and put them between the 2x2 and the back slats and then filling the holes in the back slats. it worked for now--it was still an awesome 1st project and i learned A LOT!

Claiming Our Space (not verified)

Thu, 05/27/2010 - 11:44

I have been wanting a pair of Adirondack chairs for our front yard. However the only versions in my price range have the rounded tops. The straight lines on your version will look great and echo the strong horizontal lines of our house.

Brooke (not verified)

Sat, 05/29/2010 - 02:39

Wow! This is great! Thank you for all your hard work put into these plans. Your amazing! I will have to try these plans and about 100 other ones. I will be linking. Thanks!

Jodi@homegrown… (not verified)

Sat, 06/05/2010 - 09:51

I was able to assemble 2 chairs in one day. I had already cut and painted all the pieces previously. They went together well, although I did have to do some math since the widths on my boards were slightly smaller than the dimensions in the plans. No biggie, though! I'm very happy with them. I need to put on another coat of paint and find some cushions and they're done!

Loni (not verified)

Sat, 09/04/2010 - 15:07

I'm making a "big man" adirondack for my dad, so I'm modifying your plans a bit, I'm widening it and adding some extra stringers and legs for bottom support.

My problem I'm having now is how to beef up the back to hold more pressure. I was thinking maybe extra "legs" going from the middle back support straight down to the ground? But I'm not sure if that would really add support unless I angle them back?

Thank you in advance!

claydowling

Sun, 06/05/2011 - 06:36

You should be able to build these for less. Even if you can't, there is a satisfaction in building it for yourself. My least useful chair is a stool that I built with my dad's help on his lathe. It's also my favorite because I made it, and I don't know anybody else with a chair like it.

Although given the state of my dining room chairs, I might need to start making that stool some grown up chair brethren soon. Too many broken spindles.

Guest (not verified)

Fri, 09/30/2011 - 11:28

Hi, my husband and I are anxious to make chairs for us and kids and alsoo a bench for the porch- he'd love to have a glider and I wondered if you had ideas of how to modify the bench into a glider? Thanks for all your hard work, i have such a to build list from you site! Cant' wait to start getting them done!

Guest (not verified)

Fri, 02/10/2012 - 08:48

I love this site!!!! Thank you ! I wish I could find a plan for a half circle diner booth for my dinning room, but I had so many of these plans on my wish list! Thank you so much!

Andra (not verified)

Sun, 02/19/2012 - 10:58

Would it be possible to do this project with a jigsaw and not the fancier saws that I don't own (yet).

In reply to by Andra (not verified)

Lady Goats

Sun, 02/19/2012 - 11:53

Andra, my first few projects were built only with a jig saw! So you definitely can! a piece of advice is to draw the full cut that you need to make, use a straight board as a guide to slide your jig saw against to get straight cuts, and (if needed), sand the cut to smooth it out. They'll be rough looking... but use a little caulk on the "seams" before you paint, and it'll look great.

Katrinaelizabth (not verified)

Mon, 04/16/2012 - 19:30

I was looking through your page and noticed the Little And chairs... for some reason I can not post under their pictures. Do you by any chance have th plans for building them?

jimmyp (not verified)

Mon, 05/07/2012 - 11:39

question . how much of a angle is the seat part ... the reason I ask with a BAD back , its very hard to get outta some of these , an they are very uncomfortable as well... Also wish to tll you what a great site , an great job your doing !!!!!! thank you jimmyp

msk171 (not verified)

Sat, 06/02/2012 - 19:08

To save some headaches, here are the cuts as they'll need to be done on the 1x4's so they fit on 4 boards:
Board 1: 21", 21", 30 1/2", 19 1/2"
Board 2: 21", 21", 25 1/2", 25 1/2"
Board 3: 21", 20 3/4", 20 3/4", 30 1/2"
Board 4: 30 1/2", 30 1/2", 30 1/2"

markdude

Wed, 07/18/2012 - 13:58

I love your plans, I made the Chaise Lounge first then I saw this and had to have one! Great plan, easy to build and very comfortable! Thanks!!!!!!!

Kevin Chapman (not verified)

Wed, 07/25/2012 - 15:18

I'm currently in the process of building these, just as described in the above article. How has everyone else's seats fared over time? I'm just a little skeptical on the primary use of screws. So, does it hold up well? Thanks for any responses, and I must say, with the local agway selling Adirondack chairs at a price tag og roughly $200,to be able to make one of these chairs at $70 roughly, kudos on that

jimmyp (not verified)

Tue, 10/02/2012 - 11:30

Hello , Could anyone plz help me on a question on the chair ??? ,, does anyone have any idea what angle the seat is ??? Are they hard to get down or up from the sitting position ??? thank you ... GREAT SITE

blessedmess (not verified)

Sun, 11/18/2012 - 05:41

Just have to say that I LOVE your site, Ana!! Thank you so much for all your hard work and most of all for sharing it with all of us! You and all your followers have given me such inspiration to build things that I never knew I could!! Have made a couple pieces and I am super excited about these chairs! :)

Free Plans Made Possible By Our Sponsors