Build A Modern Kid's Picnic Table, or X Benches

Submitted by Ana White on Tue, 03/23/2010 - 21:45
Difficulty
Intermediate
| Print this plan

For children's spaces that have a slightly more moderm flair. This X table and benches are kid's height, perfect for an afternoon picnic or a tea party. Special thanks to our readers for sharing their photos.

Dimensions
Table: 34 1/2" x 19 1/2" x 16" Bench(2): 31" x 11 1/2" x 8"

Preparation

Shopping List

4 – 2×4 Boards (about $2.00 Each)
1 – 2×2 Board (about $1.50 Each)
3 – 1×4 Boards (about $3 Each)
1 1/4″ Screws
2 1/2″ Screws
Wood Glue
Wood Filler

Common Materials
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Cut List

Table
4 – 1×4 @ 21 1/2″ (DO NOT CUT until reviewing step 1, ends are mitered at 45 degrees)
8 – 1×4 @ 10 1/4″ (Cut to measurement, ends mitered down 45 degrees)
2 – 2×2 @ 19 1/2″ (Ends of Tabletop)
5 – 2×4 @ 31 1/2″ (Tabletop Boards)

Cut List for TWO Benches

8 – 1×4 @ 9 1/4″ (Both ends mitered at 45 degrees, review step 4 before cutting)
16 – 1×4 @ 4 5/8″ (CUT TO MEASUREMENT One end mitered back at 45 degrees)
4 – 2×2 @ 11 1/2″ (Ends of Tabletop)
6 – 2×4 @ 28″ (Seat Boards)

Tools
Tape Measure
Speed Square
Pencil
Hammer
Safety Glasses
Hearing Protection
Drill
Miter Saw
Power Sander
Level
General Instructions

Work on a clean level surface. Use your square to check to make sure the angles between the legs are a correct 90 degrees. Use proper safety precautions and equipment. Predrill and countersink your screw holes.

Instructions

Step 1

Legs. Cut your legs so that the ends are mitered at 45 degrees, and the short point to long point measurements are 20 1/2″ as shown above. Then mark all four of the legs as shown on the blue leg above. Use the marks to guide you as you fasten with glue and 1 1/4″ screws the two legs together. To hide your screw holes, fasten from the insides of the legs.

Step 2

Fill in the Legs. Measure and cut the remaining leg pieces, shown in blue above, to fit the missing pieces on the legs. Use glue and 1 1/4″ screws to fasten together. Hide your screw holes on the inside.

Step 3

Top. Begin by fastening with glue and 2 1/2″ screws the ends (shown in blue above) to the tabletop boards. Leave a 1/2″ gap between the boards. Then attach the ends to the legs using 2 1/2″ screws. You will notice in this table’s design there is good water drainage and no pockets for water to remain and cause damage.

Step 4

Bench Legs. Build your bench legs as you built your table legs in step 1. Use 1 1/4″ screws and glue on this step.

Step 5

Step 6

Bench Seats. As you built the tabletop, do the same for the bench seats.

Finishing Instructions
Preparation Instructions
Fill nail holes with wood filler and sand and finish as desired. To get the two tone finish, you may wish to finish the tops and the X bases before assembling.
Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

A.T.O. (not verified)

Sun, 08/22/2010 - 11:38

YES, I do love this picnic table and I do want to make it, but as the others have previously posted, I would rather make it adult-sized too, and any guidelines on that would be MUCH appreciated!!

Marian (not verified)

Tue, 01/25/2011 - 08:41

Any word on an adult size version? This is adorable, would love to put one on my porch for the family.
Thanks!

Ken (not verified)

Sun, 01/30/2011 - 17:37

Wow. Very inspirational. I'm looking to tackle some patio furniture and my wife and I LOVE the look of this table. Like others who have posted comments, do you have an adult size plan?

Thanks! A great site.

nealandlori

Mon, 08/01/2011 - 11:27

I am looking at building this table for my I home daycare and need it to be long enough for about 6 kids and was thinking about lengthening it to48inches. Would this be sturdyenough with the extra length between legs? Thanks!

Guest (not verified)

Thu, 09/22/2011 - 14:08

Like everyone else, I love the table and benches for kids, and would love to see plans for adult-size in same design. Any word yet on whether you'll be adding one? Thanks so much for sharing your talent!

Spolitte

Tue, 03/27/2012 - 04:00

Ana, would there be a simple way to decrease the gap between the table top boards from 1/2 to 1/4 inch? For instance, could I go with2X3s instead of 2X4s cutting six instead of 5? I'm just not sure about the math on that or if it would even work. What do you think?