Cedar Vertical Tiered Ladder Garden Planter

Submitted by Ana White on Thu, 05/16/2019 - 05:50
Difficulty
Beginner
| Print this plan

Build your own cedar ladder garden planter for about $20 using inexpensive cedar fence pickets - free plans from ana-white.com

Garden boxes in a ladder arrangement with green plants
Close up view of the garden boxes with plants

Here’s a way to garden even if you have minimal space - a vertical garden ladder planter!  It's perfect for tiny backyards or a patio or balcony - even if you live in a small apartment in the city.

Made of cedar fence pickets, this ladder planter will hold up to the elements but only costs about $20 to build.  It’s a beginner project and you only need a few tools to tackle it.

My friend Jen built this for her mother-in-law.  She’s a beginner builder- I've asked Jen to share her tips and challenges as she built this tiered ladder planter - here's from Jen:

----

After the last project I couldn't wait to get started on this one. Another simple build with great results! What I like about this is it could be used as a regular flower planter, an herb planter, or as I did with herbs and flowers to mix it up a little.

I got right to work and got all cuts done and layed out. Then I started attaching with the handy staple gun. Did I mention I love that thing! I'm pretty sure it's my new best friend - quick and easy, that's how I like it!

The compound miter saw is great for the angled cuts. I needed 10 of the end pieces at 15 degrees off square, not parallel. Instead of adjusting the miter from side to side I simply made my first end cut, then used it as a template to mark the rest of the boards as I cut. Then all I needed to do instead of adjusting the saw is flip the board each time I cut. It worked much better than how I invisioned it would in my head.

Once I had all the end pieces cut, I attached them to the sides with the staple gun. 

After that I measured my opening and cut the bottom pieces as I went I shoved them in from the top, and there were my five boxes done. I shot a few staples for extra hold on the bottom pieces from the outside of each box.

Now for the frame. I was a little intimidated by the top cut, but my saw was already set to 15 degrees, so I just wacked the ends off parallel as directed in the cut list. Then I used a carpenters square to cut the back off the tops, perpendicular to the 15 degree top cut.  It sounds complicated but it actually is easy.  TIP: If you don't have a carpenter's square, just use a scrap of wood or even a hardcover book.

I didn't have a circular saw, so decided to use the jig saw to cut this part. I haven't really used a jig saw before, but all and all it went pretty well. I just took my time and was sure to stay on the outside edge of the line I had drawn. I won't like, the first cut wasn't perfect, but it worked.

After the first upright was cut, I used it to trace the line on the second board. Then, once again, used the jig saw to cut on the traced line. This time it went even better. Practice makes perfect!

Now came the time to attach the boxes to the frame. I started from the top and worked my way down. I marked my starting point on both uprights at the same time for consistency.  Then I screwed the box to one leg from the inside of the box, then placed the other leg and did the same. 

First box down!

Now I had a starting point for the rest of the boxes. So I cut a spacer at 6 inches (see photo below) to make the placing easier. Be sure to keep the spacer at an angle to follow the line of the first box attached. Once I had it placed I screwed the second box from the inside of the box to the frame, and so on and so forth with the rest of the boxes. 

 

It made it easier to turn the frame on its side to place the screws. Clamps are your friend here if you don't have an extra hand.

 

 

Now all I had to do was stand it up, and there was the finished product, a beautiful versatile vertical planter!

 

 

Be sure to drill holes in the bottom of each box to allow for drainage. I drilled after it was all attached, but you could do it after building the boxes before attaching them to the frame.

 

Now it was time to plant it! I showed my mother-in-law the planter and she loved it, so I decided it would look great in her back yard. 

 

So off we went to get some flowers and herbs. 

 

 

Turned out pretty well if you ask me!

 

 

 

It's amazing what you can build with $20 bucks in lumber in a couple of hours!

 

I hope you have as much fun building this as I did!

 

---

 

Thanks Jen!  Of course, plans follow - please share your finished planter with us if you build!!!

 

XO Ana + Family

 

Dimensions
Diagram showing dimensions for cedar ladder planter
Dimensions shown above

Preparation

Shopping List

5 - 5-1/2" wide cedar fence pickets (dogeared is fine) 72" length

2 - 10' long 2x6

20 - 2-1/2" long exterior decking screws (for attaching boxes to legs)

1-1/4" galvanized nails or staples (for making boxes)

Cut List

10 - 2x6 @ 5-1/4" both ends cut at 15 degrees off square, ends are NOT parallel

10 - 5-1/2" wide cedar fence pickets @ 23-1/2"

5 - 5-1/2" wide cedar fence pickets @ 20-1/2" (cut to fit)

2 - 2x6 @ 68-3/8" both ends cut at 15 degrees off square, ends ARE parallel

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Drill
Jigsaw
Miter Saw
Staple Gun
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

Attach two of the longer cedar fence picket pieces to two ends. I used 1-1/4" galvanized staples, but you could also use screws or nails.

Step 2

I placed the bottoms in from the top, and then added a few staples to keep them in place.

Step 3

The sides are simply cut with ends parallel at 15 degrees, then the back is cut off perpendicular to the top 15 degree cut. It's easier than you'd think. I used a jigsaw but the right tool would have been a circular saw. Start your cut on the top as you will have more to bit into.

Step 4

Mark the placement of the top planter on both legs first to make sure you place the planter in exactly the same spot on both legs. Then I attached from inside with 2-1/2" exterior decking screws. The 2x6s I used were very hard to drill into, so I ended up predrilling as well.

Step 5

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

sherardmc

Mon, 03/07/2016 - 20:18

Yes, I had already commented that I figured out that the actual dimensions of stock lumber are different from the nominal dimensions and clears up my first question.  But what about my second question.  Can you clarify the actual dimensions of the 10 end pieces?

sherardmc

Tue, 03/08/2016 - 09:22

It looks to me that the end pieces are made from the 2x6 cut at 8-1/8" as shown in the diagram but not @ 5-1/4" as described in the cut list.

MarPHL

Sun, 03/27/2016 - 06:11

I love this planter and I was all gung ho about making it, but then I priced out the lumber and it came to $116...cedar is expensive where I live! (Philadelphia, PA) I have considered using the ACQ treated lumber, which doesn't have arsenic, and I've heard mixed opinions. I would be using it to plant strawberries and herbs. Any thoughts?

Justjess1125

Tue, 03/27/2018 - 19:58

So I'm confused how do you get a 2x 6 which means it's only 5.5 inches wide to be 5.25 inches wide at the bottom when cutting a 15 degree angle? That would only be 1/8 inch off either side which means you could only cut off a tiny corner piece which would not look like the pic

DragonSoundz

Sat, 06/06/2020 - 19:21

Hey y'all - I think there does need to be a clarification/correction on the cut list for the end pieces. Each end piece should be 5-1/4" at the BOTTOM only (see STEP 1) , which means that the TOP should be around 8" (or 8-1/8" as shown in the main 'Dimensions' graphic above the preparation list). Another commenter mentioned this, and I figured it out while trying to do the math. I haven't tried yet but i'll keep y'all posted -- I'm gonna try the following cut for the end pieces: 10 pieces of 2x6 @ 8 inches (5 ends from each 2x6x10' should leave about 80", plenty left for each side post).

Justjess1125

Tue, 03/27/2018 - 20:22

If the pickets are 5.5 inches tall then why cut the 2x6 to 5.25? It leaves a gap 

Jim Hinton

Sun, 04/05/2020 - 09:15

Hi, so I have built many of these and they are fantastic. The only thing I wanted to mention i s that the bottoms just dont drop in, at least not low enough to have enough room for dirt. You really need a skill saw or table saw added to this list of tools. I always need to rip each bottom a good bit to get it to fit properly. I would go out on a limb and say this is the most difficult part of the building process.