Changeable Play Stand (Lemonade, Market, Post Office, Theater, Bakery and More!)

Submitted by Ana White on Fri, 11/08/2013 - 09:58
| Print this plan

Free plans to build a play stand inspired by Land of Nod, that transforms into a Lemonade Stand, Market, Puppet Theater and Post Office and more.

Hi DIY Friends!


Happy Friday!!!


I'm so very excited today to debut brand new plans for you! 


As you know, I've been teaming up with my good friend Jaime from That's My Letter to bring you a new gift plan each week between now and Christmas.



It's not just a fun way to countdown to the Holidays, but also a great way to get those handmade gifts tackled early!


I'm especially excited about today's plan - because it's really 6 (or more!) plans in one!!!



It's a lemonade stand ....



But then flip it around (and swap the sign out!), and it's a market!



Or it could be a post office ...



Or even a puppet theater!



And all the signs store up top!



Jaime was so kind to make up patterns for each of these different themes (buntings, curtains and banners), and share the free patterns with you right here.


Of course, plans follow for the play stand, but please take a second first to check out lots more information, photos, building details, and tips from Jaime at That's My Letter.


Thanks so much Jaime!


Happy Building!

XO Ana



Dimensions shown above - measure first and adjust - it's perfect for pretend play for preschoolers, but may be short for older kids.


Shopping List

1 - 1x6 @ 10 feet long

2 - 1x2 @ 8 feet long

1 - 1x4 @ 8 feet long

2 - 1x3 @ 8 feet long

1 - 1/4” plywood 24” x 24”

1 - 3/4” dowel 30” long

Cardboard or foam board for signs

1 1/4” finish nails

Chalk board paint or chalk board decal

Cut List


2 - 1x6 @ 24”

1 - 1x6 @ 25 1/2”

4 - 1x2 @ 24”

3 - 1x4 @ 24”

1 - 1/4” plywood 24” x 24”

2 - 1x6 @ 12”

1 - 1x3 @ 25 1/2”

2 - 1x3 @ 27 1/2”



2 - 1x3 @ 30”

1 - 1x3 @ 25 1/2”

2 - 1x2 @ 25 1/2”

1 - 3/4” dowel @ 30”

Thick cardboard or foam board for signs 7 1/2” x 25 1/2” (you want these to be lightweight to prevent falling hazard)

Tape Measure
Speed Square
Safety Glasses
Hearing Protection
Kreg Jig
Miter Saw
Brad Nailer
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!


Step 1

Start by making the basic box with the top and sides.

Step 2

Add the rungs for the back shelves.

Step 3

And then the back shelves themselves - notice they sit flush to the 1x2 rungs, but don't make it to the front of the 1x6 sides.

Step 4

Jaime also recommends adding a fourth 1x2 at the top - flush with the 1x4 shelf backs - to give the plywood (next step) something to attach to at the top.

Step 5

Step 6

You'll need something to keep the play stand from tipping forward or backward - these guys will do the trick. NOTE: If you go higher, you may need to make these wider - use your best judgement here.

Step 7

Now for the top - find the center, and attach the short 1x3 in the center.

Step 8

Then attach the longer 1x3s on either side, overextending equally.

Step 9

Now for the sides of the hutch top - those get attached in the notched area on the ends.

Step 10

Next, attach the top shelf ...

Step 11

And then the sides for holding the signs ...

Step 12

Then add the dowel ..

Step 13

And finally, it's time for the signs - I recommend lightweight foam board just to prevent any injury and because it's cheap and easy to work with and comes in a variety of colors.

Step 14

Jaime has free patterns for the buntings here - so check them out too!

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.



Tue, 11/12/2013 - 20:39

I love this and I absolutely need to build this for me (oh, and my daughter). Haha. =D We could have so much fun with it for years to come, instead of the cardboard playhouse I made a year or two ago that is slightly askew now. Then, we could turn around and use this as a bake sale / garage sale stand!


Wed, 04/02/2014 - 07:05

I needed a shelf in our play area upstairs in front of a window. With a few modifications this little playstand/theater was the perfect solution. Submitting a brag post now! Thank you so much for the idea and the plans!


Wed, 04/02/2014 - 07:05

I needed a shelf in our play area upstairs in front of a window. With a few modifications this little playstand/theater was the perfect solution. Submitting a brag post now! Thank you so much for the idea and the plans!