Child's Bench with Arbor

Submitted by Ana White on Wed, 08/28/2013 - 09:42
| Print this plan

Free plans to DIY a kids arbor bench!

Hi everyone! Are you ready for another dose of DIY?

A little while back, my dear friend Kirsten from the Crafting Chicks - who built this amazing play kitchen -

and I teamed up, this time on a Child's Garden Arbor bench!

How stinking cute is that????

Believe it or not, this one's actually pretty easy to build!  We've of course got you covered with the free step by step plans below.

But want to see lots more photos of this bench?  And more details on those pillows and construction photos?  Please take a second to stop over and check out Kirsten's building post here.

Thanks Kirsten!

XO Ana

Dimensions shown above


Shopping List

2 – 1x6 @ 8 feet long
1 – 2x2 @ 8 feet long
2 – 1x2 @ 8 feet long
2 – 1x4 @ 10 feet long
4 – 1x3 @ 8 feet long
1 ¼” galvanized screws
2” galvanized screws
3” galvanized screws (just need a couple)

Cut List

4 – 2x2 @ 48” (Legs)
6 – 1x2 @ 16” (Side trellis rails)
4 – 1x4 @ 52” (seat supports and top)
12 – 1x6 @ 16” (seat and backrest)*
12 – 1x3 @ 24” (Flower pot base) (top trellis)
1 – 1x3 @ 36” (Seat back support)
1 – 2x2 @ 33” (seat back base)
1 – 1x2 @ 33” (seat back top)

*for the 1x6 @ 8 feet long, cut 5 – 16” long and then the remaining will be approximately 15 ½” long. Leave this shorter piece for the ends of the seat back that are slightly shorter to conserve boards.

Tape Measure
Speed Square
Safety Glasses
Hearing Protection
Circular Saw
Power Sander
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!


Step 1

Attach with 2” screws and glue. Check for square.

Step 2

Build seat, then attach legs. Note - seat can be attached higher for older children as well.

Step 3

These are for the flower pots. You can space as you like.

Step 4

Make sure the distance between the 2x2 is the same at the top as at the seat. Screw on with 2” screws and glue.

Step 5

Step 6

Step 7

Step 8

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.



Tue, 05/20/2014 - 20:48

I'm really wanting to build this. It will be my "second" project. My first was just a quilt ladder.

I'm nervous that it's going to be more difficult to tackle than I think. I have read the instructions a few times already and it seems like some things are missing. maybe because each piece isn't labeled "A", "B", etc. Will the instructions make a little more sense when I have each piece of cut wood in my hand? Thanks!


Sun, 10/05/2014 - 10:36

Made this over the past month (a few hours every Sat/Sun), just finished painting it and had a trial run with the little people that will be using it when the sun comes back! - Love the plans, very easy and I'm a complete novice!

Thank you Ana White!


Fri, 11/14/2014 - 02:40

Can someone help me with converting the sizes to centimeters? For example; I don't how much 48 3/4, 441/2 or 14 5/8 is.

This is what I already found (am I right?):

33 inch: 83,82 cm

24 inc: 60,96 cm

52 inch: 132,08 cm

Greetings, Erica