Dollhouse Bookcase

Submitted by Ana White on Thu, 12/13/2018 - 22:30
Difficulty
Intermediate
| Print this plan

Build your own dollhouse bookshelf with our free woodworking plans.  Uses off the shelf 1x12s and basic joinery.

If you’ve got a good miter saw, you can make this bookcase in no time. I have always loved this simple design. Our free plans include step by step diagrams, shopping list and cut list.

dollhouse bookshelf diy plans
Dimensions
dollhouse bookshelf dimensions
51 1/2 " tall by 45" width by 12 1/4" deep

Preparation

Shopping List
  • 4 - 1x12 @ 8 feet
  • 1 - 1x4 @ 4 feet
  • 1 - 1x2 @ 8 feet
  • 1/4″ plywood cut 45″ wide x 51 1/2″ high, cut in a house shape with the vertical ends at 38 1/2″ (measure for exact fit)
Common Materials
2 inch screws
2 inch finish nails
120 grit sandpaper
primer
paint
paint brush
Cut List

Main Carcass

A) 2 – 1×12 @ 38 1/2″ (top edge cut off at 30 degree angle)

B) 2 – 1×12 @ 12″ (Bottom Vertical Dividers)

C) 3 – 1×12 @ 42″ (Shelves)

D) 1 – 1×12 @ 17 1/2″ (Top Vertical Divider, top edge mitered down at 30 degree angle)

E) 2 – 1×4 @ 1 1/2″ (Side Footer)

F) 1 – 1×4 @ 45″ (Front Footer)

G) 2 – 1×12 @ 27 1/2″ (Top Edge Mitered down at 30 degrees)

 

Trim for Windows and Doors

H) 6 – 1×2 @ 4″

I) 4 – 1×2 @ 4 3/4″

J) 4 – 1×2 @ 10 1/4″ Plywood 1/4″ plywood cut 45″ wide x 51 1/2″ high, cut in a house shape with the vertical ends at 38 1/2″ (measure for exact fit)

Cutting Instructions

Start by cutting all the boards as directed above. Review the diagrams to see how the angles are cut. Unless otherwise directed, use 2″ nails and glue on all joints.

Tools
Tape Measure
Speed Square
Safety Glasses
Hearing Protection
Drill
Circular Saw
Miter Saw
Brad Nailer
Power Sander

Instructions

Step 1

Use the above diagram to help guide you. Please note that the measurements are close approximations and the miter saw will cut the exact angle for you.

Step 2

Windows and Doorways. From Boards A, cut the window holes out as shown above.

Step 3

Windows and Doors. First build the window and door frames as shown above, using 1 1/2″ nails. Then center the frames on the openings cut in step 2 and nail the frames into the openings. If you are painting the frames different colors, you may wish to paint and finish the bookshelf and the frames seperately, and then fasten the frames to the bookshelf.

Step 4

Once the sides, A, are complete, begin working on the center. First nail boards B and C together, as shown above. Then fasten D to the top shelf. Once B, C, and D are completed, nail the sides A on.

Step 5

Step 6

Footer. Now fasten the front footer, F, to the front of the bookshelf as shown above.

Step 7

Top. Fasten the top as shown above. Make sure you nail from each of the top pieces into the opposite top piece at the top of the gable end.

Step 8

Cut and add the plywood to the back, using glue and 1 1/2″ nails.

Step 9

Finishing. Fill nail holes with wood filler and sand and finish as desired.

Comments