Farmhouse Bed (California King Size)

Submitted by Ana White on Thu, 06/20/2019 - 13:09
Difficulty
Intermediate
| Print this plan

The blog favorite Farmhouse Bed, now in California King! This bed plan is a must read, as the construction is a tad different to accommodate no 4x4 posts and an easier method of joining the siderails with the headboard. Special thanks to JME Blog for their marvelous photos!

Collections
blue farmhouse bed
white farmhouse bed
black farmhouse bed
Dimensions
farmhouse bed dimensions california king
80 1/2" x 91" x 57"

Preparation

Shopping List

9 – 1×8 boards, 8′ Long

1 – 1×3 board, 8′ Long

2 – 2×6 board, 8′ Long or Stud Length (doesn’t matter)

13 – 2×4 boards, 8′ Long or Stud Length (doesn’t matter, you may need more or less depending on if you have a box spring or not)

3″ self tapping wood screws

2 1/2″ self tapping wood screws

2″ self tapping wood screws

1 1/4″ nails for a brad nailer

Common Materials
primer
wood conditioner
paint
paint brush
Cut List

Headboard

  • 4 – 1×4 @ 72 1/2″ (Panel Trim)
  • 2 – 1×3 @ 30″ (Ends of the Panel)
  • 9 – 1×8 @ 30″ (Main boards in the Panel)
  • 2 – 2×4 @ 34 1/2″ (Inner Leg for Headboard)
  • 2 – 2×4 @ 54″ (Outer Leg for Headboard)
  • 1 – 2×4 @ 78 1/2″ (Top of Legs and Panel for Headboard)
  • 1 – 2×6 @ 80 1/2″ (Top of Headboard)
  • 2 – 2×4 @ 10″ (Bottom Leg Piece for Headboard)

 

Footboard

  • 4 – 1×4 @ 72 1/2″ (Panel Trim)
  • 2 – 1×3 @ 15″ (Ends of Panel)
  • 9 – 1×8 @ 15″ (Main Boards in the Panel)
  • 4 – 2×4 @ 21″ (Legs)
  • 1 – 2×4 @ 78 1/2″ (Top of Legs and Panel for Headboard)
  • 1 – 1×6 @ 80 1/2″ (Top of Headboard)

 

Siderails and Frame

  • 2 – 2×10 @ 87 1/2″ (Siderails)
  • 2 – 2×4 @ 88 1/2″ (Side Cleats)
  • 8 – 2×4 @ 69 1/2″ (Joists, you can use less if you have a box spring, may need more if your mattress is flimsy or you choose not to add plywood to top)
  • Optional plywood on top of joists
Tools
Tape Measure
Speed Square
Pencil
Hammer
Safety Glasses
Hearing Protection
Drill
Circular Saw
Brad Nailer
Power Sander

Instructions

Step 1

Front of Headboard Panel. Lay out the panel pieces on a clean level surface. Take a measurement of the total length and cut your trim boards to this measurement (approximately 78 1/2″). Then fasten the trim pieces to the panel as shown above. Use the 1 1/4″ nails and glue. Attach from the back to hide your nail holes.

Step 2

Back of Headboard Panel. In the same manner as step 1, fasten the back trim pieces to the headboard. This is shown above. Use glue and 2″ nails. This will be the back of the headboard, as your nail holes are showing.

Step 3

Inner Leg. Predrill and countersink your screws, attaching the inner leg to the headboard panel as shown above. Use glue and the 3″ screws.

Step 4

Outer Leg. Fasten the outer leg to the inner leg, using the 3″ screws and glue. Again, use the countersink bit. Keep top and outside edges flush.

Step 5

Step 6

Bottom Leg Piece for Headboard. Use the 2″ screws and glue to attach the bottom leg piece. Countersink your screws. You may need to shorten or lengthen the bottom leg piece, depending on the thickness of your side rails. Take a measurement of your side rails before cutting this piece.

Step 7

Footboard. Except for the changes in the legs as shown above, the footboard will be assembled just like the headboard. The footboard leg pieces are identical in size and there is not bottom leg piece.

Step 8

Siderails and Frame. Begin by building the frame using 3″ screws and glue. The above joists are shown spaced every 12″. You may need to add more if you are not using a box spring (standard maximum slat spacings is 6″), and you could possibly get away with less if you have a good box spring. Remember, king beds often have 2 box springs.
After you have built the frame, attach the side rails to the frame. Keep the front edges flush. The bottom edge of the frame will overhang the siderails by 5/8″. Please note that you can adjust the height of the frame to suit your needs, higher for no boxspring, lower to accomodate a box spring.

Step 9

Attaching the siderails to the Headboard. You will only need a few screws on each side rail to attach the siderails to the frame because the bottom leg piece holds the weight. Predrill and countersink your screws, using 2 1/2″ screws. Do not use glue here.

Step 10

Attaching to the Footboard. Fasten the bottom frame joists directly to the footboard panel as shown here. Use the 2″ screws, but no glue.

Finishing Instructions
Preparation Instructions
Fill any visible nail holes with wood filler and sand and finish as desired.

Comments

Col

Sun, 07/31/2016 - 14:07

Hello, I was wondering if you recall what stain/paint color you used on this bed. I'm loving the color and pull love to utilize it on the bed we're making now! Thanks!

HelloSunshine

Tue, 02/07/2017 - 18:07

I have seen several people ask about paint color but no response. I would love to know the color also. Another thing, several questions about actual shopping list. I want to make sure I get the right amount of the right stuff. Thanks!

Spcschaffer

Tue, 06/19/2018 - 06:05

When building this bed would carriage bolts through the post and into the side rails on the headboard be possible versus using screws thst can strip over time? 

Brian Famous

Thu, 06/21/2018 - 12:45

There are many options for attaching the side rails to the headboard.  I'm not really a fan of screws.  Carriage bolts work, but you have to have a cut out to attach a nut on the other side.  You could do barrel nuts and furniture bolts, and there is even types of bed rail brackets that need mortises and those that do not.

I have a somewhat detailed summary article of each type on my blog if you want more info on your options.

spectralcicada

Sat, 10/05/2019 - 14:30

I am VERY crabby that several items from the materials list are missing. I got back from buying lumber and I am missing a bunch because you didn’t include them. PLEASE fix this! 

Free Plans Made Possible By Our Sponsors