Farmhouse Bed - Queen Sized

Submitted by Ana White on Sun, 05/19/2019 - 13:30
Difficulty
Intermediate
| Print this plan

This beautiful farmhouse bed can be made for just a fraction of the cost to buy - all from standard, off the shelf lumber!  You won't need a pocket hole jig or any special tools to build.

This bed has been built thousands of times and is a reader favorite.  You can also find the twin version, king version, and all our farmhouse bed plans here.

Collections
White farmhouse bed with distressed edges built by Ana White

Having a beautiful bed can transform any bedroom.  It's the most important piece in your bedroom, but can also be the most expensive.

Over a decade ago, I built my first farmhouse bed (pictured above).  We still use it today, it's still as strong and sturdy and beautiful as ever.  And it only cost about $120 to build then - thousands less than buying!

Farmhouse Bed Plans

We updated the original farmhouse bed plans to use less tools, less materials, but be just as beautiful!  You won't need a pocket hole jig - just a drill, nailer and a saw, to tackle this project.

The plans are below.  Please let us know in the comments or add a brag post on how your farmhouse bed turned out.  Thank you for using our plans.

 

NOTE: This bed plan has been updated and improved.  If you need the original plans, we have created a printable PDF for your convenience.

Dimensions
diagram of queen farmhouse bed showing dimensions
Dimensions fit a standard Queen Mattress 60" x 80"

Preparation

Shopping List

12 - 2x4 8 feet long

2 - 2x6 8 feet long

2 - 1x10 8 feet long

2 - 4x4 8 feet long

1 - 2x2 8 feet long

6 - 1x6 8 feet long

4 - 1x4 8 feet long

100 - 1-1/4" long brad nails

75 - 2-1/2" long self tapping wood screws 

Cut List

HEADBOARD CUT LIST

2 - 4x4 @ 54"

2 - 2x2 @ 30"

11 - 1x6 @ 30" 

2 - 1x4 @ about 60-1/2" - measure and cut to fit

1 - 2x4@ 67-1/2" - measure and cut to fit

1 - 2x6 @ 69-1/2" - measure and cut to fit

 

FOOTBOARD CUT LIST

2 - 4x4 @ 21"

2 - 2x2 @ 8"

2 - 2x2 @ 3"

11 - 1x6 @ 15" 

2 - 1x4 @ about 60-1/2" - measure and cut to fit

1 - 2x4@ 67-1/2" - measure and cut to fit

1 - 2x6 @ 69-1/2" - measure and cut to fit

 

MATTRESS SUPPORT FRAME/SIDERAILS

3 - 2x4 @ 83-1/2"

1 - 2x4 @ 60-1/2"

2 - 2x4 @ 12-1/2"

2 - 1x10 @ 80"

20 - 2x4 @ 32" - can be as short as 30" if you need to burn up scraps

Cutting Instructions

Cut all boards except as noted to measure and cut.  We recommend using a compound miter saw for the straightest cuts, but you can also use a circular saw and a carpenter's square - just make sure your cut ends are nice and straight.

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Drill
Miter Saw
Brad Nailer
Power Sander

Instructions

Step 1

Attach the longest 2x2s to the longest 4x4s, flush to the back edge with 2-1/2" self tapping screws.  

Step 2

Layout the 30" 1x6 boards flat, side by side.  Measure the overall width of all the 1x6 boards.  Cut two 1x4s to this measurement.

Nail the 1x6 boards with glue to the 1x4s.  Apply glue between the 1x6 boards as you go.

Make sure the panel is built square by measuring opposite diagonals (outside top corner of 1x4 to outside bottom corner of opposite 1x4) and adjusting so the opposite diagonals match.

Step 3

Attach the headboard panel to the 2x2s on the legs with 2-1/2" screws.  Only screw to the headboard panel at the top and bottom portion backed by the 1x4s.

Also attach the panel from the front 1x6s to the 2x2s with 1-1/4" brad nails.

Step 4

Measure and cut the 2x4 for the top.  Attach with 2-1/2" screws.

Step 5

Repeat steps for the 2x6 top, leaving a 1" overhang on all four sides.

This completes the headboard build.

Step 6

The footboard is constructed exactly as the headboard, with the exception of the 2x2 cleats and the overall height.

Attach the 2x2 cleats with 2-1/2" screws.  The smaller cleat may split on you since the wood piece is so small.  You can predrill holes to help prevent wood from splitting.

Step 7

Build the panel and attach to the 2x2 cleats.

Step 8

Attach top 2x4 and 2x6 to the footboard with 2-1/2" screws.

Step 9

Attach the 2x4 cleat to the footboard, set in the 2x2 cleats, resting on the bottom cleat.  Use 2-1/2" screws to attach the 2x4 to the 4x4 legs.

Mark the headboard legs as shown in the diagram, and attach 2x4 cleat to the 4x4 legs with 2-1/2" screws.

Step 10

Use 2-1/2" screws to attach the headboard support between the cleats.

Step 11

Center legs add a ton of support and strength to the bed.  

First attach the shorter 2x4 "legs" to the center 2x4.  Then place the center 2x4 in place inside the bed, and attach to the footboard and the headboard 2x4.

Step 12

Measure and cut to fit the 1x10 siderails.  

Attach with 1-1/4" brad nails and glue.

NOTE: If you find your 1x10s need to be attached at the top, you can buy small L brackets and use to attach 

Step 13

Cut the wood slats from remaining 2x4s and set inside the bed with about a 1/2" gap in between each slat.  You only need one screw on the siderail cleat to attach - but you can also add screws to the center support.

 

 

Finishing Instructions
Finish Used
I gave this bed an Antique White finish, but have done natural wood and other colors with the same success. I choose to distress this bed by lightly sanding outside edges. I also ran a flat bladed screwdriver down any groves in the planks to highlight the planking in the panel.

Comments

swimbecky (not verified)

Fri, 10/01/2010 - 18:02

I'm so excited to have found your site! I have just sent my hubby 3 of your tables that I'm choosing between, and a headboard plan... but now I found this whole bed and I want to build it, too! I can't wait to get started on your projects!

Is there somewhere on this site that has the plans for this bed in a King? Thanks so much, Ana!

Jill (not verified)

Thu, 11/18/2010 - 12:30

Help! I am trying to make a full size bed. I will use a box spring. How do I do this? Seems like 2x4 or 2.6 is overkill. Anyone done the bed and use a boxspring and can help me with the boards and cuts?

Thanks so much!

Guest (not verified)

Sun, 08/07/2011 - 22:46

So I want to use our box spring with this plan and I re did the plan in google sketch up just to make sure I understood everything before I actually started buying and cutting wood... and I just wanted to see what you thought about my idea... I measured our entire mattress set... (box springs and mattress) and it is 20 inches tall. So I measured from the top of the pink piece (where the box spring sits) of wood in the image above (in my plan in goolge sketch up... that is with the green piece 10 inches off the floor) and it seems like I would basically loose the headboard behind my mattress and box springs... I hope that all makes sense... should I just make the posts taller to compensate for the box spring being at the level where the mattress usually would sit in these plans? like make my posts 9 inches taller because that is how tall my box spring is? Would that look funny? and Would I also have to make the foot board 9 inches bigger all around so it didn't look silly? Please email me back I am trying to figure this out!

Colin (not verified)

Mon, 11/22/2010 - 16:39

Ha! I was just thinking today... now how I'm going to work this with a box spring... THANKS ANA, perfect timing!

PS - for those of you looking for the 4 1/2" screws, HD has 4 3/4" which work great. They are near the decking screws and come in packs of 8, need 3 packs for maximum support.

Jessica Harris (not verified)

Fri, 11/26/2010 - 13:49

;