Farmhouse Bench - No Pocket Holes Version

Submitted by Ana White on Tue, 06/04/2019 - 13:26
Difficulty
Starter Projects
| Print this plan

This farmhouse bench is easy to build and is rustic and substantial.  It is designed to match our Farmhouse Table Plans. 

Collections
farmhouse table with matching bench

Reader submitted photo by  EHAYS216 

We love this sturdy and substantial farmhouse bench.  Designed to be built using standard off the shelf lumber, just the way farmhouse furniture has been built for hundreds of years.

Build it to match our farmhouse table plans, or use it as a stand alone piece on the end of a bed, or in your entryway.

Farmhouse Bench Plans

Dimensions
dimensions image for farmhouse bench
Dimensions are shown above

Preparation

Shopping List

4 – 2x4s, stud length or 8 foot length

2 – 1x4s, 8 foot length

1 – 1×2, 8 foot length

2 1/2″ screws

2″ screws 

Common Materials
120 grit sandpaper
primer
wood conditioner
paint
Cut List

8 – 2x4s @ 16 1/2″ (Legs)

2 – 1×4 @ 2 1/4″ (Spacers)

2 – 1×4 @ 6″ (End Aprons)

2 – 2×4 @ 12″ (Stretchers)

2 – 1×4 @ 61″ (Side Aprons)

2 – 1×4 @ 9 1/2″ (Inner Aprons)

5 – 1×2 @ 9 1/2″ (Supports)

4 – 2×4 @ 65″ (Bench Seat Boards)

2 – 1×4 @ 14″ (Breadboard Ends)

 

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Circular Saw
Power Sander
Drill Bit Set
General Instructions

The Farmhouse Bench is designed to work with this Farmhouse Table, but there is no reason you could not modify the dimensions or use it as a coffee table or outdoor bench. If you plan to build the Farmhouse Table, starting with the bench will give you a chance to test out your skills on a smaller version. For those of you who have a pocket hole system, you can use the pocket holes to build your bench seat separate. You can also fasten your aprons directly to the legs without spacers.

Instructions

Step 1

Legs The notches and stretchers on the legs is optional. Notch out your legs (for full instructions see the Farmhouse Table post) and laminate your legs together in pairs of 2 with glue and 2 1/2″ screws. Then take note of the placement of the spacers and attach to the insides of the legs. This will differ depending on the leg. Attach with 2″ screws and glue.

Step 2

End Aprons Attach end aprons to the spacers as shown above. Use glue and 2″ screws.

Step 3

Stretcher The stretcher gets attached in the same method. Screws and glue.

Step 4

Bench Frame Build the bench frame, keeping the 1×2 supports flush to the top. Easy method is to flip it all over and keep the supports flush to the bottom :)

Step 5

Step 6

Seat Boards Find the center of the supports and begin attaching seat boards from the underside. Work with the boards to minimize gaps as you go. Attach all seat boards. If you have a pocket hole system, you would build your bench seat separate, and then attach.

Step 7

Breadboard Ends If you have a pocket hole system, you would attach the breadboard ends directly to the seat boards in step 6. Otherwise, attach to leg bases.

Step 8

Finishing If you are staining, be very careful to not let glue dry on the project, as these areas will not take stain. Fill holes with wood filler, sand and paint or stain as desired.

Comments

redwoodrustics

Sun, 05/08/2016 - 09:06

and actually for the bench to slide easily underneath i'd say reduce the overall size by 8 inches length wise because the stretchers on the farmhouse table (pocket hole style) are 67 inches long so you'd want the overall bench length to be 64 or 65 inches long to comfortably slide in and out without dinging the sides of your table

moonprysm

Fri, 05/27/2016 - 14:26

Ok so I've done my math several times to check this. Lumber list calls for 4 2x4x8. This is 384 in. But the cut list calls for 8 16.5, 2 12, and 4 65. That's 416 inches. 

hulkster51

Tue, 09/20/2016 - 10:21

the cut list calls for 2x4 seat boards , but the bread boards are called for as 1x4these are not going to fit. so yes i guess my bread boards will have to be 2x4. would i be wrong to use 1x4 as seat boards instead of 2x4s, and when io build the table should the top be 1x4 instead of 2x4 tso as to match the bench seat , or does it matter as i sell this stuff and i am new to carpentry

dhaynes1206

Thu, 11/17/2016 - 17:54

The plans have 1x4 for breadboard ends, but 2x4 for the bench tops? I used 2x4 for my breadboard ends, suppose you could double up to have same thickness. I also shortened this to allow the benches to be slid under the farm table when not in use to save space! great plans.

Traddman

Mon, 01/16/2017 - 09:53

I have everything cut but don't know where to join the boards with the kreg pocket holes.  Any help would be appreciated. I am using the bench for my nephew's wedding and want it to look nice with no screws showing.  Also what size screws I should use.  The base is made of pine and the top is cypress.  Thank you