Flip Top Storage Bench / Coffee Table

Submitted by Anonymous (not verified) on Tue, 02/02/2010 - 08:57
Difficulty
Intermediate
| Print this plan

A simple bench that holds a suprise in it's aprons. Flip the top up and find the perfect spot to store magazines, mittens, or anything else that can fit! The bench also features a roomy bottom shelf perfect for shoes and blankets. I had this bench under my wall mounted flat panel, and used the flip top for remotes and dvds, and the bottom shelf for controllers. This bench is really easy to build too!

18″ High, 48″ Wide, 15″ Deep

Preparation

Shopping List

1 – 12′ 1×12 pine board
2 – 1×2 pine boards
1 – 1×3 pine board
2 – 1×4 pine boards
2 – sets of basic butteryfly hinges

Common Materials
2 inch screws
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Cut List

2 – 1×12 @ 42 1/2″ (Shelves)
4 – 1×2 @ 17 1/4″ (Leg Pieces for the Sides)
4 – 1×3 @ 17 1/4″ (Leg Pieces for the Front and Back)
2 – 1×2 @ 39″ (Bottom Shelf Trim, Front and Back)
2 – 1×4 @ 39″ (Top Storage Compartement Sides, Front and Back)
2 – 1×2 @ 8 1/2″ (Bottom Shelf Trim, Sides)
2 – 1×4 @ 8 1/2″ (Top Storage Compartment Sides, Sides)
1 -1×4 @ 48″ (Top, Back)
1 – 1×12 @ 48″ (Hinged Top)

Tools
Tape Measure
Speed Square
Pencil
Hammer
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Circular Saw
Power Sander

Instructions

Step 1

Legs and Bottom Shelf. Begin by building all four legs. You will need to nail through the 1×2 part of the leg into the 1×3 leg piece, keeping outside edges flush. Notice how the 1×3 part of the legs is on the front and back, and the 1×2 parts are on the sides. Be aware of the leg placement as you assemble the bench.
Then fasten the legs to the bottom shelf, leaving a 3″ clearance under the bottom shelf on each of the legs. I suggest that you mark each of the legs 3″ from the bottom first, and then assemble the bench. Use glue and 2″ nails, fastening through all the leg pieces into the shelf edges.

Step 2

Top Shelf. Fasten the top shelf, leaving 2 3/4″ from the top of the shelf and the top of the bench. As you did in step 1, I recommend marking each of the legs 2 3/4″ down from the top, and lining this mark up with the top of your top shelf. Fasten through the legs into the shelf with the 2″ nails and glue.

Step 3

Bottom Shelf Trim. Measure and cut your bottom shelf trim from 1x2s. These are pieces noted as pieces D and should be approximately 39″ long. Trim both the front and back of the bench. Keep the bottom edges flush. The top will overextend by 3/4″ the bottom shelf. Use the 2″ nails and glue.

Step 4

Top Shelf Storage Compartment Sides, Front and Back. Measure and cut pieces E, a 1×4 approximately 39″ long. Keeping the bottom edge flush with the bottom of the top shelf, fasten E to the top shelf along the bottom edge. Use the 2″ nails and glue. Then toenail, or nail at an angle from the top ends of E into the sides of the leg pieces. This will keep the top edges of the storage compartment in place.

Step 5

Step 6

Bottom Shelf Trim, Sides. As you did in step 3, measure and cut boards F and trim out the sides of the bottom shelf. Boards F should be approximately 8 1/2″ long, cut from 1x2s, and are flush with the bottom of the bench (and not the top, as shown above).

Step 7

Top, Back Piece. Mark piece H 2″ from the outsides for the overhang on the ends. Then mark piece H 1″ along the back edge for the back overhang. Then position piece H on top of the bench and fasten in place using the 2″ nails and glue. Be sure to fasten to the leg pieces and the back of the storage compartment.

Step 8

Hinged Top. Use the hinges to attatch the 1×12 to the 1×4. It is a good idea to use magnetic clasps to keep the 1×12 in place and prevent warping when the top is closed. Look closely at the first picture and you will see the hinges slightly show on top of the bench. If you would like completely invisible hinges, you can invest in support hinges designed for lift top toy boxes and benches. The cheap butterfly hinges work great for me.

Comments

Jake

Wed, 04/25/2012 - 19:29

I am nearly finished with the lift top bench. It is coming out better than I thought it would. I was planning on using it in my garage to store tools near where I am working but it may end up in my "Cueva de Hombre." It is very sturdy if anyone is interested. Unfortunately I changed the depth of the storage to accommodate some tools without considering what that really meant. I have now spent a day constructing vertical extensions of the upper front and side panels. A real learning experience. I have also built three of the step - tables (I call them step - stools) with my grandson and his friend from across the street. Both are 10 years old and handled the work beautifully. Each stool / table is put together a little differently in order to help them learn about counter sinking, pocket joints, and using the miter box. Lots of fun.