Large Modern Porch Swing Couch

Submitted by Ana White on Tue, 07/14/2020 - 14:42
Difficulty
Beginner
| Print this plan

Build your own porch swing in a couch size!  Fits standard 24 x 24 inch outdoor cushions.  Basic design is easy to build with a simple tools and off the shelf materials.  Free plans by Ana-White.com

diy porch swing couch plans
This plan has been updated to increase the back height for more comfort when leaning back and keeping pillows in place.  The original plans are still available here.
large porch swing bed plans
Dimensions
porch swing couch plans
Dimensions are shown above. Seat is designed to fit 3 - 24" x 24" cushions, or one 24" wide x 72" long cushion.

Preparation

Shopping List
  • 5 - 2x4 @ 8 feet long
  • 8 - 1x6 @ 72" long (can also use cedar fence pickets, but must be properly sanded or planed first)
  • 70 - 1-1/2" to 2" long self tapping exterior use screws (look for the star bit ones)
  • 50 - 2-1/2" to 3" long exterior self tapping wood screws (look for the star bit ones)
  • Hardware to hang swing and swing chain

Cut List

2 - 2x4 @ 69" - seat frame front and back

2 - 2x4 @ 25-3/4" - seat frame sides

2 - 2x4 @ 22-3/4" - seat frame center supports

2 - 2x4 @ 16-1/4" - arm rest front supports

4 - 2x4 @ 30-1/4" - back supports

2 - 2x4 @ 27-1/4" - arm rests

8 - 1x6 @ 72" 

Tools
Tape Measure
Speed Square
Pencil
Hammer
Safety Glasses
Drill
Circular Saw
Power Sander
Level
Drill Bit Set

Instructions

Step 1

Use the longer screws to build the frame for the seat, two screws per joint.

Step 2

Add center supports to the seat frame with the longer screws, use two screws per joint.

Step 3

Attach back rest and arm rest supports to the frame, all outside edges flush.  Use three screws per joint, using the longer screws.

Step 4

Attach arm rest to the tops of the arm support and to the back support.  Use two screws per joint, using the longer screws.

Step 5

Attach the top seat slat to the back supports, all outside edges flush, using the shorter screws, two per joint.

Step 6

Attach remaining back supports using the longer screws into the seat frame, two per joint.

Then attach to the top seat slat with shorter screws, two per joint.

Step 7

Attach remaining seat back slats to the back with the shorter screws, two per joint.

Step 8

Attach seat slats to the seat frame, using the shorter screws, two per joint.

Step 9

We hung ours on an existing playground swing set, but your situation may likely vary from mine. Here is a good article on proper hanging of swings. On this swing, you will want to hang from the side aprons of the seat frame - that's where the majority of your weight will be. Also, I hung ours at a very slight (approximately 5 degree) back angle, to increase the comfort level.

DISCLAIMER: This is a very heavy swing and must be properly hung. Build, hang and use at your own risk - We are not liable for personal injury, loss or death from use of swing. 

Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

Guest (not verified)

Mon, 06/27/2011 - 11:24

Yes, PLEASE! I don't have a place to hang a swing, but really want to build one with legs, freestanding and moveable. This is such a cute bench--perfect!

Michele Villano (not verified)

Sat, 07/09/2011 - 10:17

We have our swing completed! Yay! We can't decide whether to use chain or rope to hang it. We are more concerned with the security of using a rope. What is the best way to make it secure and safe? Rope is definitely more cost effective! Thanks!

Guest (not verified)

Tue, 08/02/2011 - 18:53

just made it this weekend! directions were great! i used longer screws and screws where the finish nails would be and pressure treated wood as this will be hanging in the woods hopefully for years. so sturdy, i think a baby elephant could use it! your site is just the best. my sister is going to make something too!

Gretchen Knobl…

Mon, 08/22/2011 - 18:41

I love this. Everyone loves it. The feeling of calm and peacefulness that you get when you glide back and forth is just awesome! Thanks for making it so easy to accomplish this Ana!

Gina Robinson (not verified)

Wed, 08/31/2011 - 19:53

We have had a metal A-frame in our yard for years, from an old swing..I have been wanting a new swing for it for ever....we found your site and fell in love with the swing...bought all of the materials...even bought awesome cushions for it...then realized the frame is only 73inches wide...which means I guess we have to shorten the swing, :-( ...but how much do I have to shorten it? How much room does there have to be between the edge of the swing and the frame? Where else can I place the eye bolts, so I have more clearance.

Victor Busciglio (not verified)

Fri, 09/16/2011 - 09:04

This is the difference between an impersonal home and one that bears your personal touches and really makes you feel at home. You're doing well and i'm so impressed for showing to us what sometimes people missed from putting more relaxing place at home.

mcfirefly (not verified)

Mon, 01/30/2012 - 13:30

I live in a small apartment with a balcony on which I cannot hang a swing, and it's too small for an A-frame swing support. I'd like to build a glider out of this swing, but the hardware for a glider costs about $70 with everything included, dedicated metal glider hangers, and these hinges that supposedly make the gliding smooth (they are the most expensive part). But why not hang a glider like you do a porch swing, on simple chains? The problem is, I don't know where or how long to make the chains. The length could be easy enough to adjust, if the supporting structures were of the right size and in the right places, but I wonder whether they should match, or perhaps would swing better if offset or if with a slightly different length (saying so in print, I think that the same length and lined up, but not too tight, would be the way to go). The frame to hang it on would be a frame that wraps around the swing, same height that the arms would be, I don't know how much clearance between the frame and the swing should be, and the swing will attach by means of an under-support that could be something like the arms built again under it, although I'm not sure that's strong enough. I am looking at porch gliders and their hanging set-up, and it seems to me that this will be possible, and since the money is not presently available, I have a little time to think about it, but it would be wonderful for summer. So it creaks a little bit, just like a lovely old porch swing! I could sleep on it! Does anyone have any ideas or suggestions about how to do this?