1. Home
  2. Plan Catalog

Locker Bookshelf - Full Size

|save this plan
Submitted by Ana White on Fri, 08/30/2019 - 11:52
Difficulty
Intermediate
| Print this plan

Need better organization in your entryway or hall, but it's too narrow for a hall tree or bench, and don't want to drill holes in your wall?

Build your own locker unit!  It's the size of a bookshelf, and is freestanding - so you can move into your home without drilling holes in the wall.  You can build it with basic tools and our free step by step plans with full diagrams, shopping and cut lists.

Need a smaller size?  We have plans for a smaller locker bookshelf here.

freestanding wood locker bookshelf

Photo by KHAWLEY5 - modified in height

Dimensions
locker unit freestanding wood project
Dimensions are shown above.

Preparation

Shopping List
  • 44 – 1 1/4″ Pocket Hole Screws
  • 2″ brad nails
  • 1″ brad nails
  • 3 – 1×12 – 12 foot Pine or Whitewood Boards
  • 4 – 1×2 – 8 foot Pine or Whitewood Boards
  • 1 – 1×3 – 4 foot Pine or Whitewood Board
  • One sheet 1/4″ plywood, paneling or MDF
  • Wood Glue
  • Wood filler or Pocket Hole Plugs 
  • Coat Hooks
Cut List
  • 2 – 1×12 @ 67 1/4″ (sides)
  • 3 – 1×12 @ 46 1/2″ (shelves)
  • 1 – 1×12 @ 49 1/2″ (top)
  • 2 – 1×12@ 36 1/2″ (locker sides)
  • 1 – 1×2 @ 48″ (header)
  • 2 – 1×2 @ 65 3/4″ (side trim)
  • 1 – 1×2 @ 49 1/2″ (crown)
Tools
Tape Measure
Speed Square
Pencil
Hammer
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Circular Saw
Jigsaw
Brad Nailer
Power Sander
Level
Drill Bit Set

Instructions

Step 1

Build the Box

This is so easy. Just drill pocket holes on both ends of all of the shelves and the top ends of the sides. Drill three pocket holes per end, as shown in the diagram. Then mark the sides for the joints of the shelves. Apply glue to the shelves and screw in place with 1 1/4″ pocket hole screws and glue.

Step 2

Locker Dividers

Mark the middle shelves as shown above. Drill pocket holes on both ends of each of the dividers. Use 1 1/4″ screws and glue to attach dividers to the shelves.

Step 3

Back

I purposely choose to make the back 48″ wide so that 1) you don’t have to rip plywood and 2) you don’t have to waste plywood. Use 2″ nails and glue to nail the back on. Make sure you all the shelves and dividers too.

Step 4

Face Frame

Drill pocket holes on both ends of the footer and header. Drill two pocket holes per end. Mark legs 3″ from bottom and screw the footer and header to legs as shown above. Tack the frame to the face of the cabinet.

Step 5

Attach front top trim to finish out the front edge of the cabinet.

Project Type
Hall Trees
Bookshelf and Bookcase Plans
Lockers
Room
entry way
Style
Cottage Style Furniture Plans
Farmhouse Furniture

Comments

Ana White (not verified)

Wed, 09/29/2010 - 07:01

Thank you Shawnda! I really like Fresh Home (even before they featured me) because there is so much DIY in their articles. And that really sounds like a project you just accomplished! Can't wait to see what you build!

Free Plans Made Possible By Our Sponsors

Ryobi Tools
Kreg Tools
shelf help