Madeline Changing Table

Submitted by Ana White on Fri, 04/16/2010 - 20:58
Difficulty
Advanced
| Print this plan

Featuring three drawers, one cupboard and a large changing area, this changing table will meet the needs of your new baby, while still looking beautiful. Works with the rest of the Madeline Changing Wall. Special thanks to our readers for sharing their photos.

Collections

I don’t normally post plans on Saturday, but so many of you have been asking, I wanted to get these plans up so you can work on them this weekend.

So I’ve been teasing you with this system for months, giving you everything BUT the base unit, and I promise, it wasn’t on purpose. It’s just that the base unit has a lot of doors and drawers, which makes for a much longer plan. The rest of the collection can be found here, and I suggest you review the entire collection before building anything.

So without much more talk, let’s just get right to the plan.

Dimensions
Overall dimensions are shown above

Preparation

Shopping List

2 Sheet of 3/4″ MDF or 3/4″ A1 Plywood, cut into 1×16 boards 

1 Sheet of 1/4″ MDF or Plywood or Lauan for the Back (you can use scraps for the door rails and stiles) 
1/2 Sheet of 1/2″ Plywood for the Door and Large Drawer Faces 
1 – 1×6 Board, 10′ Long (for the Small Drawers) 
1 – 1×10 Board, 10′ Long (for the Large Drawers) 
1 – 1×2 Board
3 1/4″ Floor trim or base moulding 
 3/4″ Edge Trim (3/4″ wide) 
 2″ Screws 
1 1/4″ Nails and Screws 
5/8″ Nails 
Wood Glue 
Wood Filler 
Sand Paper 
Finishing Supplies 
2 Sets of Undermount Drawer Slides, 14″ long (for large drawers) 
1 Set of Hinges
Knobs
Shelf Pins (for adjustable shelves)
Common Materials
paint
paint brush
Cut List

Cutting List for Box 

2 – 1×16 @ 33 1/4″ (Sides) 
1 – 1×16 @ 30″ (Vertical Divider) 
2 – 1×16 @ 22 3/4″ (Horizontal Dividers) 
1 – 1×16 @ 38 1/2″ (Bottom) 
1 – 1×16 @ 40″ (Top) 
1 – 1/4″ Plywood or MDF @ 40″ x 34″ (Back) 
 Cutting List for Trim on Box 
1 – 1×2 @ 22 3/4″ (Top Inside Trim) 
1 – 1×2 @ 38 1/2″ (Bottom Inside Trim) 
1 – 1×2 @ 5 3/4″ (Front Drawer Divider Trim) 
1 – 1×2 @ 14″ (Drawer Guide) 
1 – 3 1/4″ Base Moulding @ 40″ (Base Moulding, cut out) 
1 – 3/4″ Edge Trim @ 40″ (Front Edge Trim) 
 Cut List for 2 Small Drawers 
 2 – 1×16 @ 9 1/4″, then trimmed down to a finish size of 14″ x 9 1/4″ (Drawer Bottoms) 
2 – 1×6 @ 9 1/4″ (Drawer Backs) 
4 – 1×6 @ 14 3/4″ (Drawer Sides) 
2 – 1×6 @ 10 3/4″ (Drawer Faces) 
 Cut List for Large Drawers 
 2 – 1/2″ Plywood @ 22 1/2″ x 10 3/4″ (Drawer Face Backs) 
4 – 1/4″ Plywood @ 22 1/2″ (Drawer Rails) 
4 – 1/4″ Plywood @ 7 3/4″ (Drawer Stiles) 
2 – 1×16 @ 21″ cut down to a finished size of 21″ x 14″ (Drawer Bottoms) 
4 – 1×10 @ 14 3/4″ (Drawer Sides) 
2 – 1×10 @ 21″ (Drawer Backs) 
 Cut List for Large Door Face 
 1 – 1/2″ Plywood @ 29 3/4″ x 14 3/4″ (Door Backs) 
2 – 1/4″ Plywood cut into strips 1 1/2″ @ 14 3/4″ (Door Rails) 
2 – 1/4″ Plywood cut into strips 1 1/2″ @ 26 3/4″ (Door Stiles)

Tools
Tape Measure
Speed Square
Pencil
Hammer
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Circular Saw
Jigsaw
Power Sander
General Instructions

Work on a clean level surface. Use necessary safety equipment and precautions. Always check for square after each step. If you are working with MDF, use drywall screws and predrill the entire distance of you screw shaft to avoid splitting the MDF. Always predrill and countersink your screws. Mark joints on both sides of the joint so you know where the joint is and where to fasten the joint. Keep outside edges flush. Do not forget the glue
THIS IS AN ADVANCED PLAN and will be easy to make a mistake. Please do not attempt as a first project.

Instructions

Step 1

Build the Box. Begin by attaching the inner dividers together, as shown above. Start on the inside and work outward. It always is a good idea to mark out your joints on both the inside and the outside of your boards so you know where to line up your boards, and where to fasten. Also in this step, if you would like to add a shelf to the right compartment, cut the shelf (or shelves) at 15″ from 1×16 scraps. You can also attach later using shelf pins to create adjustable shelves. Remember that your boards are 3/4″ thick. Use 2″ screws and glue.

Step 2

Back. Square up your project and add the back. The easiest way is to use lots of glue and 1 1/4″ brad nails (either with your pneumatic nailer set on a lower pressure setting to keep the nails from shooting through) or with a good ole hammer. You can use the scraps from the back as your door and drawer face rails and stiles.

Step 3

1×2 Inner Boards. Begin by building the top drawer divider system by fastening the blue, green and pink boards together. Use 2″ screws (you won’t need many). Then fasten the Green and Pink boards to the box, usine 1 1/4″ screws and glue. Fasten the boards from underneath to hide your screws. Don’t forget the bottom board!

Step 4

Base Moulding. Cut your bottom moulding and attach, using 1 1/4″ nails and glue. Then cut out the moulding as shown above using a jigsaw.

Step 5

Step 6

Small Top Drawers

Because these drawers are so small, I have decided to not add drawer slides to the drawers. If you would like to add drawer slides, you would need to build the drawer 1″ less on the sides to account for a 1/2″ side mount drawer slide. Build 2 Drawers.

Construct your drawer by first fastening the back to the bottom using 2″ screws. Then fasten the sides to the bottom and the back using 2″ screws and glue. Then attach the face. I like to fit the drawer into the drawer housing without the face attached, then line the face up with the drawer and fasten in place centering the face on the opening.

Step 7

Large Bottom Drawers

These drawers are quite a bit larger, and you will need to use drawer slides. I have designed these drawers with undermount slides to make them easier to install, but you could also use side mount slides. You would then need to make your drawer 1″ less wide to accommodate 1/2 clearance side mount slides.

1. Drawer Face. Build your drawer face as shown above. Use glue. Clamp and let dry flat, stacked on top of each other, on a level surface, with a heavy object on top.

Step 8

Drawer Box. First cut your drawer bottom using a 1×16 @ 21″, and then trim the 1×16 down to a finished size of 21″ x 14″. By doing this, you will get a more square drawer bottom. Then fasten the back to the bottom using 2″ screws, then the sides. Use glue. Mount the faceless drawer onto the undermount drawer slides. Push the drawer all the way into the drawer housing, adjust so that the faceless drawer is inset 3/4″. Set the face on the drawer box and screw in place, centering on the opening.

Step 9

Large Door

Build the Large Door Face as you did the large drawer faces.

Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

Calmari

Thu, 03/07/2013 - 10:15

I am interested in the plans for the side hutches, but following the link gives a 'file not found' error. I tried using the link that Jen G. posted above but got an error with that as well. Any help would be appreciated!