Mimi's Hall Tree Hutch

Submitted by Ana White on Mon, 02/06/2012 - 11:38
Difficulty
Intermediate
| Print this plan

About Project

Free plans to build a hall tree. Simple step by step plans include 10 diagrams, detailed cut list and shopping list, and photos.

I am so glad you all liked Mimi's Hall Tree. On Friday, I put together plans for the bench shown at the base of this hall tree. 

So of course we need to tackle the hutch plans today!

A special thanks to Mimi for sharing with us her beautiful DIY Hall Tree.  Make sure you stop over and thank Mimi and check out lots more amazing DIY projects.
Dimensions

Preparation

Shopping List

1 - 1x10 @ 8 feet long
1 - 1x10 @ 6 feet long
1 - 1x12 @ 4 feet long
1 - 1x6 @ 4 feet long
1 - 1x2 @ 8 feet long
1 - 1x3 @ 8 feet long
1 - sheet 1/4" plywood or beadboard
1 - stick 6 feet small crown moulding
Use either 2" screws or 1 1/4" pocket hole screws to build

Common Materials
3/4 inch finish nails
1 1/4 inch finish nails
2 inch finish nails
Cut List

2 - 1x10 @ 53" (Sides)
1 - 1x10 @ 32 1/2" (Shelf)
1 - 1x10 @ 13" (Divider)
2 - 1x2 @ 32 1/2" (Front Trim)
2 - 1x3 @ 32 1/2" (Back Trim)
1 - 1x6 @ 32 1/2" (Base)
1 - 1x12 @ 38" (Top)
1 - beadboard or 1/4" plywood @ 34" x 53" (Back)

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Jigsaw
Miter Saw
Brad Nailer
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

Notch out hutch sides as desired. 

 You can also check out how I did my smiling mudroom sides for different ideas.

Step 2

Next, add the shelf.

Step 3

Notch out the tops of divider to fit a 1x2 on front and 1x3 on back. Use a jigsaw to make square cuts. Attach divider to shelf.

Step 4

Next, add the front and back trim, making sure the divider is centered on the 1x2 and 1x3.

Step 5

Step 6

And the back trim.

Also, not pictured, add the base trim flush to bottom back of hutch
with 3/4" pocket holes and 1 1/4" pocket hole screws on back side, or 2" countersunk screws and wood glue.

Step 7

Next, add the top. Notice the 2" overhang on sides and front.

Step 8

Attach beadboard or plywood to back.

Step 9

Apply moulding as desired, mitering corners to fit.

Step 10

Finally, secure to bench and wall to prevent forward tipping.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

Comments