Printer's Console

Submitted by Ana White on Mon, 08/20/2012 - 10:40
Difficulty
Advanced
| Print this plan

Free plans to build console inspired by Anthropologie Illusorio Cabinet.

Prepare yourself.

You may have to drop everything you had planned for today.

The dishes might just have to wait.

Can you order pizza tonight?

Because you are going to want to build this!!!!!

This console was built by Ashley from Shanty2Chic from plans we worked on together that follow. From Ashley:


I was so excited for Ana to get to work on the plans for this beauty! At about 10% of the cost, I was able to not only build a functional storage cabinet for our bedroom but I was able to customize it to our taste as well! This was a super easy build and I love how the planked doors give the illusion of drawers! Thank you Ana!

Please stop over and check out Ashley's build post for tips, tricks, and lots more photos! Thank you Ashley!

And if you can't drop everything today ... make sure you pin this plan for when you do have time to build it! Thank you!

Dimensions
Dimensions shown above.

Preparation

Shopping List

2 – 2x2 @ 8 feet long
1 – 2x2 @ 8 feet or stud length
5 – 1x2 @ 8 feet long
2 – 1x4 @ 12 feet long
2 – 1x6 @ 10 feet long
2 – 1x3 @ 8 feet long
1 sheet 3/4" plywood cut into strips 15 ¾” wide (referred to as 1x16 throughout plan) x 8 feet long
Optional back
1 ¼” PH screws
1 ¼” finish nails
2 sets euro style inset hinges or narrow profile hinges (installed in gap between door and face frame)
Optional ¼” plywood for back
24 knobs or handles

Cut List

FACE FRAMES
4 – 2x2 @ 35 ¼”
2 – 2x3 @ 35 ¼”
4 – 1x2 @ 26 ¼”
2 – 2x2 @ 26 ¼”

DRAWER FACES
10 – 1x4 @ 26”
2 – 1x6 @ 26”
10 – 1x2 @ 26”
4 – 1x3 @ 30 ½”

BOX
2 – 1x16 @ 56 ½”
2 – 1x16 @ 33”
1 – 1x6 @ 30 ¾”
2 – 1x6 @ 27 7/8” (shelves)

TOP
3 – 1x6 @ 59”
1 – 1x3 @ 59”

BACK
1 – ¼” plywood 58” x 33”

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Circular Saw
Brad Nailer
Power Sander
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

You'll want to build the face frames first so you can make sure those drawers fit in there good!

Step 2

And then build your doors to fit the openings. You can even attach with hinges and keep in place with catches. It will certainly be much easier to do this now than later!

REMEMBER what door goes in what opening :)

Step 3

IMPORTANT!!!! Before attaching ANY of the box pieces, drill ¾” PHs on front and back edges of all box pieces so you can attach face frame easily in later steps. Hide PHs on inside, underside or top of cabinet.

Step 4

Now attach those face frames to the box ....

Step 5

Step 6

Step 7

Add shelves if desired at desired locations.

Step 8

And then a back in desired.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

Comments

baklund

Mon, 08/20/2012 - 13:13

Any chance on adding plans to do drawers instead of doors?

Nicole 1016

Mon, 08/20/2012 - 14:44

I am wondering the same thing about thew drawers. This would be even more fabulous if all of those faux drawers were actually drawers!

lisah (not verified)

Mon, 08/20/2012 - 17:32

Oh my god. i might have to tweak the plans and only build it half-width to make bedside tables

Guerrina

Tue, 08/21/2012 - 11:12

Grabbed my attention RIGHT away! As with Lisah, I'd love for nightstands and with a bit more tweaking for a bathroom vanity in the full bath and a narrower version for my small dining room for linens and such! Ahhh! The possiblities!

Joni

Tue, 09/04/2012 - 17:12

I think the plans have a typo in them, and the last 2 items under the Cut List (for the box) should be changed from 1x6 to 1x16.

Crystal A (not verified)

Sat, 09/08/2012 - 21:34

I agree with Joni, the plans do look like they have a typo. Unfortunately, I've already made all my cuts, so I'm off to buy more 1x6's. Also, I think you will need 3- 1x3's, not 2. I made all the cuts as indicated, with little waste, and I'm short about 90" of 1x3 material
I'm excited about starting to put this together!