Rhyan End Table

Submitted by Ana White on Wed, 02/02/2011 - 22:45
Difficulty
Advanced
| Print this plan

End tables featuring two drawers and a large open top shelf. Open base design. Square styling.

Collections
Dimensions
Dimensions are shown above.

Preparation

Shopping List

1/2 – sheet of 3/4″ hardwood plywood (or MDF for paint grade) measuring 48″ x 48″ or larger
4 – 2×2 @ 8 feet long
2 – 1×6 @ 8 feet long
1 – 1×2 @ 8 feet long
Hardware
2 1/2″ screws, 1 1/4″ screws, or 2 5/8″ trim screws
wood glue, wood filler and finishing supplies
2 sets of 16″ Drawer Slides

Cut List

2 – 3/4″ plywood or MDF @ 17″ x 17″ (Shelf and Top)
3 – 3/4″ plywood or MDF @ 17″ x 12 1/4″ (Sides)
2 – 3/4″ plywood or MDF @ 17″ x 14 1/2″ (Drawer Bottoms – note different than dimensions shown in plan)
4 – 2×2 @ 26″ (Legs)
12 – 2×2 @ 17″
5 – 1×2 @ 17″ (Drawer Slide Spacers and Drawer Trim)
4 – 1×6 @ 17″ (Drawer Sides)
2 – 1×6 @ 16″ (Drawer Backs – note different than shown in plans)
2 – 1×6 @ 16 3/4″ (Drawer Fronts)

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Circular Saw
Power Sander
Level
Drill Bit Set

Instructions

Step 1

Cut Plywood

I was just at The Home Depot the other day, and spotted these gorgeous 4×4 posts (been lusting after Crate and Barrel’s Big Sur Table for the longest time). An associate gladly cut the 4×4 to size for me, and the cuts were just perfect and only took a minute. So if your local store has a good staff, perhaps bring this cutting diagram in. Always remember that the saw blade takes up approximately 1/4″ and you cannot just mark out all the cuts and go – your pieces will not be accurately cut. My advice is to cut two strips that are 17″ wide, and then cut the strips into the 17″, 12 1/4″ and 14 1/4″ pieces. And then from the scrap cut your final back piece.

Step 2

Sides

Start building the sides by attaching 2x2s to the top and bottom. You will need to build 2 of these – well, actually, go ahead and build three of these.

Step 3

Side Drawer Slides

Okay, now only build two of these from the three that you build in step 2. Make sure that there are no screws sticking out here these are the drawer slide spacers.

Step 4

Legs

From the two pieces with the drawer slides, add legs as shown above.

Step 5

Step 6

Shelf/Top

Add the top and shelf as shown above.

Step 7

Back and Shelf Trim

Okay, here’s where you add that third piece you built in step 2 – to the back. Also trim out the shelves and the bottom with 2x2s as shown above.

Step 8

Drawer Trim

A little piece of trim for between the drawers . . .

Step 9

Drawers

You will need to build two drawers. It’s basically 1x6s surrounding the bottom plywood. You should always build your drawers to fit the opening in the end table, not to shown dimensions. Check the clearance on your drawer slides (normally 1/2") and adjust the door measurements to fit your endtable.

Step 10

Drawer Slides

The blue boards in the diagram above are for attaching the drawer slides to the drawers. This drawer is designed for a standard slide requiring 1/2″ clearance on each side of the drawer. Adjust so that there is an even fit around the drawers and the drawers slide smoot

Comments

armymom64

Fri, 02/28/2020 - 08:08

I guess I missed something, but is there a ledge or something that supports both the shelf and table top? I put one in but wondered if I did something wrong.