Rustic Media Console Cabinet

Submitted by Anonymous (not verified) on Wed, 11/25/2009 - 15:16
Difficulty
Advanced
| Print this plan

This simple closed media console can be built with or without drawers. Add a rustic finish and hardware, and create a beautiful spot for your tv - or use as a console table.

Dimensions
41″ wide x 28″ high x 13″ deep

Preparation

Shopping List

3 - 1x12 @ 8 feet long
4 - 1x2 @ 8 feet long
2 - 1x3 @ 8 feet long
1 - 1x4 @ 4 feet long
1 - 1x6 @ 8 feet long
Hardware
Plywood for back (optional)

Common Materials
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Cut List

Cut List for the Cabinet

2 – 1×12 @ 23 3/4″ (Sides of Cabinet)
3 – 1×12 @ 38″ (Shelves)
2 – 1×12 @ 1″ (Drawer Guides)
1 – 1×12 @ 39 1/2″ (Top of Cabinet)
2 – 1×2 @ 11 1/2″ (Top Side Trim)
2 – 1×2 @ 41″ (Top Front and Back Trim)
4 – 1×2 @ 26 1/2″ (Sides of Legs)
4 – 1×3 @ 26 1/2″ (Front and Back of Legs)
1 – 1×2 @ 36″ (Back Bottom Trim)
1 – Beadboard Plywood 41″ wide x 25 1/4″ tall
2 – 1×4 @ 8 1/2″ (Side Footer Piece, Cut Out Design)
1 - 1×4 @ 36″ (Front Footer Piece)
1 – 1×2 @ 36″ (Front Middle Shelf Trim)

Cut List for ONE Drawer

1 – 1×12 @ 34 1/4″ (Drawer Bottom)
1 – 1×6 @ 34 1/4″ (Drawer Back)
2 – 1×6 @ 12 1/4″ (Drawer Sides)
1 – 1×6 @ 35 3/4″ (Drawer Front)

Tools
Tape Measure
Speed Square
Hammer
Hearing Protection
Drill
Circular Saw
Jigsaw
Brad Nailer
Power Sander

Instructions

Step 1

Start by attaching with 2″ nails and glue the sides to the bottom shelf. Use one of the shelf pieces. Nail through the sides into the end edge of the shelf. Line up bottom edges.

Step 2

Next, attach with 1 1/4″ nails and glue the drawer guides. The drawer guides need to sit 1″ wide by 3/4″ tall.

Step 3

After the drawer guides are in place (not shown in the rest of the diagrams), add the middle shelf, as shown, 7 1/4″ from the bottom of the cabinet to the bottom of the shelf. Use 2″ nails and glue.

Step 4

Nail the Top of Cabinet in place, as shown above. Use glue and 2″ nails and nail through the top of the cabinet into the top edges of the sides. Now is a good time to check for square. (If you do not know how to check for square, see the HOW-TO section).

Step 5

Step 6

Attach the front and back top trim pieces as shown, keeping top and outside edges flush. Secure to the top of the cabinet piece and the side trim pieces with glue and 2″ nails.

Step 7

Now add the sides of legs, as shown above, keeping the front and back edges flush. Use 1 1/4″ nails and glue.

Step 8

Now add the front and backs of legs, as shown above, keeping outside edge flush with the sides of leges. Nail the front of the legs into the shelves, the sides, and the sides of the legs. This will keep the cabinet together.

Step 9

Cut the footer pieces, as shown above. Use your own creativity here! Once one piece is cut, you can use it as a pattern to cut the other pieces. Nail the footer piece in place, as shown above and below.

Step 10

Attach the Front Middle Shelf Trim Piece, as shown above. Keep the top edge flush with the middle shelf. Also shown in this diagram is the adjustable shelf. You can add this now, or later. I use shelf brackets and add later so I can adjust the shelf to the perfect height.

Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

Console Table/… (not verified)

Mon, 01/24/2011 - 08:41

[...] in Brag Blog Put on my TO-DO List Save as PDF Print this PostShare/Bookmark Builder: Krystle Blog or Website:http://alwaysanotherproject.blogspot.com/2011/01/look-what-i-can-do.html Experience Level: Some Experience Estimated Cost: $100-ish Estimated Time Investment: 12 hours (including finishing) From Plan: http://ana-white.com/2009/11/plan-tao-open-media-cabinet-knock-off.html [...]

KaceeT (not verified)

Tue, 01/25/2011 - 10:23

I really must be needing glasses, but for the life of me I can't seem to find the plan or the area that you refer to in the following…
"Here is the plan, just click on READ MORE below."

I would love to build this.
What am I missing…be polite.

Guest (not verified)

Fri, 04/08/2011 - 15:15

Poor guys....I decided to have them cut this plan. Took 30 minutes and they didn't seem pleased. I got home and the 1x2's and 1x3's are allllll off. I assume it is because the wood was slightly bent. I tried to find the best boards. Needless to say, cut your own small boards!

 

Patty (not verified)

Sun, 04/10/2011 - 19:43

This project is missing measurements for the doors. I just finished cutting all my wood. Do you have the measurements, etc?

 

Patty (not verified)

Sun, 11/06/2011 - 11:09

Hi! Was hoping to finish this project today. It has been sitting in my garage for a year--waiting on the doors. Are the door plans ever going to become available? I know I could do it myself but would like verification since I am a beginner. Hoping someone reads this before Thanksgiving....when I plan to have all tables and projects finished. Thanks!!