Shoe Dresser

Submitted by Ana White on Wed, 01/05/2011 - 20:34
| Print this plan

A narrow tilt out shoe storage unit that looks like a console table, acts like an entire shoe closet!

Special thanks to Niki for sharing her photo.

The boots are still there, but the shoes are gone.

It was indeed odd, seeing our Alaska entryway free of shoes and outfitted with a green dresser.

Mom, where are my Uggs?  In the dresser, honey.

Hey, that's not a dresser!

That's a shoe bin!

Yes, this is a shoe bin.  And these are the plans for it.

Someone once asked me: Why do women love shoes?   I responded "because they always fit, and when nothing else does, your cute shoes will distract from your jeans not fitting."  Have your dessert, and buy some cute shoes  :)  And build  :)

Modern Mod

If your taste is more on the modern side, save yourself some knobs and cut handles out.

This shoe dresser is designed to work with tight hallways and tons of shoes.

Dimensions are shown above.


Shopping List

4 – 1×8, 8 foot length
2 – 1×6, 8 foot length
scrap 2x2s for the feet
3 – 1×2, 8 foot length
4 – 3/8″ wood dowel pins, 1 1/2″ long or two sets of traditional hinges
2″ screws or 1 1/4″ pocket hole screws
1 1/4″ Screws
2″ Finish nails
wood glue
4 magnetic cabinet clasps
knobs or pulls
A used fabric belt or strap
Finishing Supplies

Cut List

4 – 1x8s @ 47″ Door Faces (measurements differ from diagrams to conserve boards)
1 – 1×8 @ 47 1/4″ Middle Shelf (measurements differ from diagram to conserve boards)
2 – 1x8s @ 48 3/4″ (Top and Bottom (measurements differ from diagram to conserve boards)
2 – 1x8s @ APPROXIMATELY 31″ (See step 2) Sides
2 – 1×6 @ 47″ (Bin Bottom) (measurement differs from diagram to conserve boards)
6 – 1×6 @ 14″ (Approximate)
4 – 1×2 @ 47″ (Bin Backs)
1 – 1×2 @ 47 1/4″ (Cleat)
2- 2×2 @ Your Base Board + 1″ (Legs)
1 – 1×2 @ 44 3/4″ (Front Apron)
2 – 1×2 @ 5″ (Side Aprons)

Tape Measure
Speed Square
Safety Glasses
Hearing Protection
Kreg Jig
Power Sander
Drill Bit Set
General Instructions

I have marked this one Advanced not because it is difficult to build, but because it could be easy to mess up. Please don’t tackle this as a first project.


Step 1

Door Faces

Cut your door faces. If you have a Kreg Jig™, attach door faces to make two doors. If not, that’s okay, I got you covered in the next step. Measure the overall height of the doors and take note of this. 1x8s differ from mill to mill, so be aware and build according to your board widths.

Step 2


Start by attaching the 1×6 to the bottom of the doors as shown above with 2″ screws or pocket hole screws. Use glue. Then cut your bin dividers according to the height of your doors and round corners off. Attach in place. If you did not build your door faces in step 1, you can use finish nails and glue to attach the door faces to the dividers. You can use more dividers to add more support for the door faces (and more division of your shoe storage).

Step 3

Bin Backs

You need something to keep the shoes from tipping out. How about a couple of 1x2s? Screw and glue in place.

Step 4


The box needs to be build around your bins, with a 1/8″ gap around the door faces. We’ve aleady accounted for the gaps on the sides of the doors, but not the top and bottom. As shown in the diagram, figure the exact measurement of the sides and cut. Build your box.

Step 5

Step 6


Now this is the tricky part. Not so much trick to do but trick for me to explain. Clamp the bins centered in their box, with a 1/8″ gap around all sides. If you don’t have clamps, 1 1/4″ screws could do the trick from the inside of the bins. Drill a 3/8″ hole at the bottommost front corner of your bins, careful to make sure the hole drills into the bins and does not miss the bins. The hole needs to be the depth of your wood dowels. Insert the dowels and test the bins out. Alternatively, you can use traditional hinges.

Step 7


Attach the footer to the bottom as shown above.

Step 8

The Used Belt

Have someone give you a hand, because this one is tricky to handle here. There’s only two front legs and the bins keep flopping open . . . I know Tilt the bin out to the desired max opening. Cut a piece of the belt to and screw it to the bin and the shelf below the bin. Make two straps per bin.

Step 9


Keep the bins shut using the magnetic clasps. I used them on the sides for a nice tight fit. Screw the cleat to a stud in the wall behind the shoe dresser to keep it in place and to keep it from falling forward when the bins open.

Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.


Chuck (not verified)

Thu, 01/06/2011 - 05:46

I think your shopping list off. I think it needs another 8' 1x8.

I was making a cut sheet for this so I could make one this weekend.

kerry (not verified)

Thu, 01/06/2011 - 06:23

Fabulous!!! I'm smack in the middle of building the kids locker for my front hallway w/ the shelf on the bottom for shoes instead of the top for bins. This, however, I NEED! I'm already thinking where it will go! Love it!!!

Lisa P (not verified)

Thu, 01/06/2011 - 06:42

OHHH I sooo need this too! 5 of us in a teeny tiny house with no storage and too many shoes! We've looked at the Ikea one every time we are there but never bought it. I would way rather build it anyways! Brilliant...thank-you.
Lisa P

Annalea (not verified)

Thu, 01/06/2011 - 07:18

Thank you Thank You THANK YOU!!!

With eight of us in the house, there's a serious shoe-storage problem around here. lol This is the perfect solution . . . and for many times less than premade options. Now, to figure out where to put it in this rental . . .

Christine (not verified)

Thu, 01/06/2011 - 07:22

Perfect for me!! We just had a "disagreement" about how we are not going to build a coat rack to go by the door (since you come right into the dining room & hubby thinks it looks tacky, but I think it is tackier to have a constant pile). But the kids STILL put their coats and shoes by the door. This way, they can be truly HIDDEN and handy!

Carolina (not verified)

Thu, 01/06/2011 - 08:45

Hi Ana! Thanks for this wonderful plan! We're planning on building it this weekend but I noticed some parts of the instructions were cut off of the pdf as well as on the website. Am I right? Thanks again, you're the BEST!