1. Home
  2. Plan Catalog

Super Easy but a Little Tricky Ladder Table Plans

|save this plan
Submitted by Anonymous (not verified) on Wed, 04/28/2010 - 21:53
Difficulty
Beginner
| Print this plan

A simple table reminicent of a small painter's ladder can work as a bedside table or a side table. This is a great project to use up your scraps.

Dimensions
21 1/2"x15 3/4"x14"

Preparation

Shopping List

2 – 1×3 Boards
1 – 1×2 Boards
2″ Screws
1 1/4″ Screws
Wood Glue
Wood Filler

Common Materials
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Cut List

4 – 1×2 @ 10 1/2″ (Top and Bottom Shelf Supports)
3 – 1×2 @ 5″ (Top Shelf Supports)
2 – 1×2 @ 9″ (Bottom Shelf Supports)
3 – 1×3 @ 14″ (Top Shelf Boards)
5 – 1×3 @ 10 1/2″ (Bottom Shelf Boards)
2 – 1×3 @ 21″ (Back Legs, ends cut at 5 degrees off square, end parallel)
2 – 1×3 @ 22 1/4″ (Front Legs, ends cut at 20 degrees off square, ends parrallel)

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Drill
Miter Saw
Power Sander
Level
General Instructions

Work on a clean level surface
Take a square after each step
Use wood glue
Countersink all screws with a countersink bit (or use Pocket Hole Technology)
Be safe, use necessary safety equipment
Remember that you can click images for a larger view

Instructions

Step 1

Build the top shelf supports as shown above using the 1×2 @ 10 1/2″ and the 1×2 @ 5″. Screw together using 2″ screws and glue.

Step 2

Using the 1×3 boards 14″ long, fasten through the supports into the underside of the shelf boards as shown above. Use 2″ screws and glue.

Step 3

Just like the top shelf, put the bottom shelf support together as shown above. Use glue and 2″ screws.

Step 4

As you did the top shelf, screw thought the supports into the underside of the shelf boards using 2″ screws and glue. Use the diagram above to guide you.

Step 5

Finishing Instructions
Preparation Instructions
Fill any visible holes with wood filler. Sand and finish as desired.
Project Type
Bookshelf and Bookcase Plans
Side and End Table Plans
Room
Bathroom
Bedroom
Craftroom
entry way
Kids and Toys
Nursery and Baby
Style
Cottage Style Furniture Plans

Comments

stcurry

Wed, 06/13/2012 - 07:46

I made one of these and I love it. My mother in law would like to have one that folds up.
I would love any ideas on an easy way to do that

wimsy (not verified)

Thu, 06/21/2012 - 05:31

I love this as a TABLE, but some of the comments say they plan to use it as a step stool. It's not safe to stand on, except perhaps by small children. Look at a "real" wooden step ladder to see how it's made if you plan to use it that way. Have fun making this, but be safe if you plan to stand on it!

Jenna D (not verified)

Sat, 12/29/2012 - 14:59

Hey Ana—this is the perfect stool for my kitchen but I wanted to get your thoughts about how much weight it can hold. It wouldn't be used for more than a few seconds to grab something, and no more than 110lbs. Do you think it's safe?

Jake

Sat, 12/29/2012 - 17:22

I have made five of these tables/stools and they can be very safe. The one in my kitchen has been there for two years and I at 180 lbs have not caused it to break. However I did build one using firing strips and it did break. Not at the joints but the leg itself. If you build it use the best pine the store has to offer (adds $5 to your total cost) and where possible throw in an extra screw especially places where the joint is in a shear orientation. After your build is complete take it out on the lawn and find someone that weighs about 200 lbs to get up and down from it several times. If it doesn't break you are safe. If it does break your test subject just lands in the yard. You can see three of the stools by clicking on my name. Actually three kids built them.

Jenna D (not verified)

Sun, 12/30/2012 - 09:13

Thank you for your tips, can't wait to build mine!

Jake

Sun, 12/30/2012 - 09:37

When you install the bottom step just measure and locate the step on either the back or front legs (use a small level to make sure that it is level between the legs and then rotate it up with a level on it (aimed front to back) until it is level then mark your locations. This is better than trying to measure. Hope you get my suggestion. Also use a good glue like Titebond II or III. III just gives you more time to work. II sets up rather quickly.

Quartney

Mon, 04/29/2013 - 13:10

I made a beautifully stained & monogrammed stool for the kids and my husband, even though I told him it was not made for a grown man, used it as a step stool and broke the lower step! Whole thing was ruined :( When I make it again, I'm going to change the arrangement of the lower step and attach it to the legs via the support wood.

Jake

Mon, 04/29/2013 - 15:14

I have not had a problem with my stools except one I made from furring strips. However, to be safe you can add a block under the lower step as added support or even attach the lower step with dowels