Vintage Crate Carts

Submitted by Ana White on Mon, 09/13/2010 - 16:34
Difficulty
Beginner
| Print this plan

Cute pallet carts made from reclaimed wood boards.

Collections

These turned out so much better than I would have ever expected for $8 each.

Especially with a few setbacks.

You all already know that I can't spell.  Stencils really should come with spell check.  Or at least you should have to pass a test before you can purchase stencils.  Or they should sell sandpaper with stencils.  Good thing I had some sandpaper handy.

And while I was working on these carts, a bee stung me.  So now I smell like vinegar too.

At least I got our wedding date right on the first try.

These crate carts were intended for my great room, but because of the setbacks, I ended up photographing them in Grace's room (that's where all the evening sun is in my house).  And I just think they look adorable filled with kids stuff.  They will look adorable as bumper cars too, ugh, I know that's coming!

Here is a breakdown of the price per cart:

  • 2 feet of 1x12 boards - $3
  • 2 sets of 1 5/8" Caster Wheels - $4
  • Reclaimed boards from pallets
  • 2" Wood Screws
  • 2" Finish Nails
  • Wood Glue

Not bad, eh?  And did I mention that my carts are made of oak?  Yep, sanded down the pallet boards, and it's oak!

You just gotta make your own!  If you don't have a pallet to reclaim, you can use 1x6s and 1x4s, but don't expect the character to be as fabulous when you use new materials. You can watch a video on how to reclaim boards on a pallet here.

Dimensions
Dimensions for the cart are shown above. If you are using reclaimed boards, your dimensions could be different than those listed above.

Preparation

Cut List

2 – 1×12 @ 11 1/2″
2 – 1×6 @ 18″ (bottom, adjust width as desired)
6 – 1×4 @ 18″ (sides, adjust width as desired)

Tools
Tape Measure
Speed Square
Pencil
Hammer
Safety Glasses
Hearing Protection
Drill
Jigsaw
Power Sander
Drill Bit Set

Instructions

Step 1

Preparation

If you have a pallet, follow the instructions in this post to reclaim the boards. Otherwise, cut all of your boards. Drill holes on the ends of the 1x6s, two per end, with a countersink bit.

Step 2

Build the Bottom and Ends

Insert screws into holes. Apply glue to the joint. Screw the bottom boards to the sides, keeping the outside flush.

Step 3

Sides

Apply glue to the edges of the bottom and ends. Be careful not to apply glue in the spaces between the side boards, as glue will not take stain. Use 2″ nails and glue to nail the side boards on.

Step 4

Handles

Mark then ends as shown above. Then drill holes with the 1 1/2″ spade bit on center with the marks. Cut between the marks with a saw to create handles.

Step 5

Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

Christina G. (not verified)

Wed, 01/19/2011 - 18:20

Hey Anna,
im so excited about your site, and cant wait to get my project on... i have found so many things on your site that i can not wait to get into my house (1st) and start building some great stuff... thanks SO much.

i do have a question, some of the plans that i have tried to save as a PDF for future quick reference they come up blank... is there another place i can find them? Thanks again... your the super best

Sky (not verified)

Thu, 02/17/2011 - 13:04

ok i have called costco, walmart, and target, non of which will give me any pallets. some say they send them back to the distributor and some say they recycle them and another says they just dont give them away and hung up before i could say "i'll buy them" any other thoughts on where to acquire some!

joeyh

Wed, 10/29/2014 - 07:51

I get my pallets from a printing company they always have alot of them, commercial printing companies.

Jesse Bailey (not verified)

Tue, 03/01/2011 - 10:47

Sky, look on craigslist.com. Don't try major retailers -- your chances are better with smaller places that think it is a pain to deal with the pallets.

Sincerely,
Jesse

MrsD2008

Tue, 04/19/2011 - 08:13

I am hoping I can start this project this weekend!  I will need my husbands help learning how to use the tools (this will be my first attempt at building anything) so I am hoping he lets me hang out in the garage and actually use his tools.  But, when I told him about it, he said he needed to work on the truck so it could be inspected on Monday (the 25th) because it's due by the end of the month......not that he could have been doing that during his three day weekend or anything...men!

Anyway--mine are going to be for dog toys.  One will say one dogs name and the other will say the other doggies name!  And, I would like to paint mine to match my living room (vision), especially if I end up using regular wood instead of a pallet.

Question: I have never stained anything and I am nervous about that.  So I think I am going to paint these.  My brain says paint THEN stencil dogs names.  I would want the crates to be a chocolate brown and the stenciled names would be either a lighter brown or off white.  Is my brain correct?  

Harry (not verified)

Wed, 02/29/2012 - 09:08

I have been looking around for crates to be used as props, and stumbled into your blog. I love it and can't stop reading it. Thank you for sharing everything.

jRoxDesigns (not verified)

Wed, 09/12/2012 - 19:05

I LOVE your toy bin! I just picked up some wooden crates and have been looking for some ideas to turn them into toy storage and your post has given me the perfect inspiration. I wrote about your crates on my blog today for Inspiration Wednesday. I'd love for you to stop by sometime!
http://jroxdesigns.wordpress.com/2012/09/12/toy-crate-storage-inspirati…
- Amber @jRoxDesigns