Wood Folding Sling Chair, Deck Chair or Beach Chair - Adult Size

Submitted by Ana White on Fri, 06/03/2011 - 12:10
Difficulty
Advanced
| Print this plan

Folding adult sized wood sling chair, also known as wood beach chairs or deck chairs. Folds flat for storage, opens up for easy relaxation! Adjusts to three positions for customized reclining. Features removable slings.

Child sized plans also available.

I know this chair has been a long time coming . . . it's also been a long time in the making. When you first started requesting a sling chair (also known as wood beach chairs or folding deck chairs) I knew it was definitely a project I wanted to tackle. I just didn't know it would take me four prototypes to finally be able to put this seal on it . . .

And believe it or not . . . it's still not done.  The stain is still a little tacky - thus the slings are pulled tight, and I couldn't find a single volunteer to test it out in a photo.
But I promise, this one is super comfy.  If you've ever sat in a sling chair, all you have to do is close your eyes and you are at the beach.  The way the sling works, you almost feel weightless.
This chair costs and estimated $25 to build.  The best deal I've found on outdoor canvas fabric, 54" wide is $8.98 per yard, for designer brands from Fabric.com...and they have Free Return Shipping too! 
Slings are reversible.  For light colored fabrics with high contrast prints, you may consider lining the slings with canvas duck fabric. 
I used Minwax Gel Stain for this chair frame for a rich even stain.  The strength and durability of this chair is highly Dependant on what type of materials you use and how you build your chair.  As shown and built by me, the Ram (200LBS + and six feet tall) approved of the design and the size.  Your chair could differ depending on the types of materials you use and the building techniques you use.
Dimensions
Dimensions are shown above.

Preparation

Shopping List

1 - 6' 1/2" Diameter Wood Dowel
1 1/2 Yards Outdoor Fabric, 54" wide
Sewing Notions and Thread
1 - 1x3 @ 48" long
4 - 1x2 @ 8 feet long
4 - 1/4" diameter bolts, 2" long with matching nuts
12 - washers to fit bolts

Common Materials
2 inch screws
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Cut List

Backrest Frame
2 - 1x2 @ 48"
1 - 1x2 @ 24"
1 - 1x2 @ 25 1/2"
1 - 1x3 @ 24"

Seat Frame
2 - 1x2 @ 44"
4 - 1x2 @ 23 3/4"
1 - 1x2 @ 22 1/4"
1 - 1x3 @ 22 1/4"

Prop-Up Support
2 - 1x2 @ 15"
1 - 1/2" Diameter Wood Dowel @ 25 1/2"

Fabric Slings
2 - Outdoor Fabric Squares @ 54" x 22 3/4"
2 - 1/2" Diameter Wood Dowel @ 22"

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Drill
Circular Saw
Power Sander
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

Build the back frame very carefully as shown above. The main weight bearing joints are going to be where the fabric slings pull on the headers - so take great care to use glue, carefully predrill holes, avoid splitting your wood, and attach in place. There is a 3/8" gap between the header boards. Drill the holes as shown above for the bolts.

Step 2

Build the smaller sling as shown above, taking great care again to create strong joints for the headers.

Step 3

Once both frames are complete, line the frames up as shown above, and insert bolts, with washers on both sides of bolt, and one washer between the two wood frames to protect the finish on your wood frames. The chair should now swing open, but there will be nothing to keep the chair from staying open. See next step . . .

Step 4

Build the propup support as shown above. Attach with bolts and washers to the backrest frame, in the remaining predrilled bolt hole. Rest between seatframe slats. You will be able to move the prop up to adjust the angle of the chair.

Time to make that sling.

Step 5

Step 6

Using a larger stitch length, topstitch edges along both (long) sides only. A decorative stitch is optional. Finish edges by tucking thread into project.

Step 7

Fold bottom and top over 1 1/2” to create “sleeves.”
Topstitch using same seam allowance as on the sides.
Finish edges by tucking thread into project.

Step 8

By threading the slings through the chair headers, then threading the dowels in the "sleeves" you create a sling that is held in place sturdily, but is easy to remove to wash or change the look up.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Project Type
Room

Comments

deanna_g

Sat, 06/04/2011 - 04:47

Yes! That makes complete sense. Thank you! I'm going to build a couple of these for my best friend's birthday. She's been wanting some chairs for her front porch and I think she'd love these!

angela r j (not verified)

Fri, 06/03/2011 - 19:35

The fabric dimensions are the same for this adult chair as they are in your plans for the child-sized chair. Shouldn't the fabric be longer and wider to accommodate for the larger chair?

In reply to by angela r j (not verified)

Ana White

Fri, 06/03/2011 - 19:50

Hi Angela, thanks for catching this. Yes, the dimensions for the adult sling differ and should be 54" x 22 3/4".

Ana White

Sat, 06/04/2011 - 13:58

You may also consider using a 3/4" Dowel for the base dowel instead of 1/2" for a stronger chair. Mine's actually 5/8" diameter, and I have no issues, but 1/2" might be not enough for a heavier load. If you do go the larger dowel size, be sure to space stops 3/4" wide instead of 1/2".

momof8

Sat, 06/04/2011 - 17:01

fabricguru.com has fabric for as low as $4.95 per yard, and shipping is 4.99 for your entire order!

Debbie Christianson (not verified)

Mon, 06/06/2011 - 04:59

I have been thinking what to give my son's preschool team, as he's heading to kindergarten and has been with them for 3 years. I think I may make these as gifts for them. That would be 6 chairs -- oh gosh. Better get started!

Guest (not verified)

Wed, 06/08/2011 - 06:44

We had a lot of fun with this chair when we were kids. We used to remove the dowel from the sling's base sleeve and watch someone sit and fall. Many times got into trouble when it was an adult that fell.

I remember our's had armrests too.

I'll make one and show that trick to my kids.

-V

Hawaiianatheart (not verified)

Wed, 06/08/2011 - 07:29

Love this chair and would like to make them for an older couple but they'd need them to be a more standard chair height. Can this be done? What changes should be made? Thanks!!!