Wood Pullout Cabinet Drawer Organizer

Submitted by Ana White on Mon, 03/21/2011 - 23:03
Difficulty
Intermediate
| Print this plan

After organizing my junk drawer successfully, I felt confident and inspired to tackle some more cabinet storage.  And of course, first up, what to do with all the princess plates, lunchroom trays and sippy cups with missing lids.

 
 
How about a drawer, right at the height of a four year old?  And how about a nice deep drawer, with a big chalkboard label on it?
 
 
Of course, you could install this drawer on the bottom shelf, make the drawer have taller or shorter sides, or even put it under the sink for trash cans . . . and attach the cabinet door to the front of it for a real pullout trash can on a super budget.  There are no limits, beyond your time and your imagination.
 
I'm going to show you today how I built this drawer for Grace (and will probably be building more drawers for my pots and pans and maybe even one for our dog  . . . ) and you can easily modify it to fit your cabinets.  I spent about $10 on the drawer, with $6 for the 1x6 (I actually had scraps so this was free for me) and about $4 for the drawer slides.  I also used half of a 2x2, so there's another buck. I made the chalkboard label with scrap plywood and chalkboard paint and glued in on.  The drawer as shown here has not yet been finished.
 
pull out drawers in kitchen cabinets
pull out drawers in kitchen cabinets
pull out drawers in kitchen cabinets
Custom to fit your Cabinets

Preparation

Shopping List
  • 1 - 1x6 @ 8 feet long
  • 1 - 2x2 @ 4 feet long
  • scrap 1/4" plywood 
  • 21" Drawer Slides
Common Materials
2 inch screws
1 1/4 inch finish nails
Cut List

Cut to fit your cabinets.

Tools
Tape Measure
Speed Square
Pencil
Hammer
Safety Glasses
Hearing Protection
Drill
Circular Saw
Power Sander
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

The first thing you need to do is measure the opening of your cabinets and the depth of your cabinets. Mine had a clearance opening (the hinges took up a little room too) of 14 1/2". Remember that your drawer slides also take up 1" all for both, so that's a total drawer width of 13 1/2". To be safe, I made mine 13" wide, and cut 2 1x6s to this length. Then I measured the depth of the opening. Mine was 22 3/4" deep. So I cut the 2x2s to the depth of the cabinet and then cut the two 1x6s to this measurement minus 1 1/2" - so for me, 21 1/4". I then cut the 1/4" plywood to 13" x 22 3/4".

Step 2

With all the boards cut, I built a simple box (used 1 1/4" pocket hole screws but you could also use 2" screws countersunk) and glue. The I tapped the bottom on with 1 1/4" finish nails and glue.

Step 3

Because these cheapo drawer slides (that actually work really well and are quite strong) are side/bottom mount, you can get away with just tacking 1/4" plywood to the bottom. The weight of the drawer contents sits right on the slides. I attached the two drawer parts of the slides to the bottom of the drawer as shown above.

Step 4

Then I attached the remaining drawer slide pieces to the 2x2s as shown here. Make sure these pieces are attached level and in the same position on both 2x2s. This is important. I used the screws that came with the slides, and followed the directions on the slides.

Step 5

Step 6

Then I simply positioned the whole setup inside the cabinet, and because of the tight fit, screwed the 2x2s to the shelf from the underside. But if you had more clearance from the top, you could screw from the top too. Used 2" screws here, just two per 2x2.

Step 7

And then just put the drawer in. The drawer is easy to remove and clean (and in my case, finish) and I really love the 2x2s in there, because they keep things from sliding under your drawer. Off to build . . . six more.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

Comments

jengil_1

Mon, 05/02/2011 - 21:12

I found heavy duty drawer slides for $3 at our local Restore. Yeah!

nikiley

Mon, 04/11/2011 - 07:32

Hi Ana!! I am sitting here figuring out what I need to get for my cabinet project.  I have a cut list ready to go.  But I can't seem to find the Getting Started page that you suggest reading at the beginning of the instructions.  Maybe I don't know where to look for it.  Also didn't you used to have a post about how to select wood and where to find what you're looking for?  

Anyway, I think I'll just go wander around until I find the right wood, but I love the new site.  Looks beautiful!
Nikki

debbie (not verified)

Thu, 06/16/2011 - 08:33

I love this!!1 I need this desperately for my pots and pans drawer.

glassbycass

Wed, 01/14/2015 - 00:19

I looked in the comments, but didn't see any solution for cabinets that do not have a shelf :( My bathroom cabinets for example desperately need sliding drawers / organizers and this project actually seems affordable & do-able! However, I was so excited by finding this tutorial and really excited while finding deals, sales, pre-used, scrap supplies,etc - that I completely overlooked a major obstacle. My cabinets do not have shelves or brace supports or anything at all actually. So ... should I now go look up how to add a shelf to a cabinet? I'm assuming the shelf must come first since the 2x2's get attached to the shelf - is there any certain way this shelf needs to be? Sorry for all the questions - the term newbie doesn't even begin to cover it. Thanks in advance for any & all help with this :)

Ana White

Wed, 01/14/2015 - 13:37

Hi! I actually think pull out drawers are even easier if you don't have an existing shelf. You'll just attach your drawer slide cabinet members directly to the cabinet itself (no 2x2 blocks are required).

If you have a euro style cabinet (meaning there is no frame on the front of the cabinet) you would just attach to the inside of the sides of the cabinet (just make sure the drawer will pass the hinges, if not you'll need to shim the drawer slides in ward with maybe a 1x2 on the hinge side - scroll through this post http://ana-white.com/2013/12/momplex/drawers-closet-tower for images)

If you have a face frame, you can attach the drawer slides directly to the face frame and the back of the cabinet - here's an example http://ana-white.com/2013/12/momplex/kitchen-cabinet-drawers-metabox- you don't need to use those slides)

Hope all this helps!

glassbycass

Wed, 01/14/2015 - 17:52

More than impressed with your quick and informative response :-D I think you are officially my hero! You are not only handy, talented and inspirational - you are kind and helpful! Thank you thank you thank you!

glassbycass

Wed, 01/14/2015 - 17:52

More than impressed with your quick and informative response :-D I think you are officially my hero! You are not only handy, talented and inspirational - you are kind and helpful! Thank you thank you thank you!

Free Plans Made Possible By Our Sponsors