These Parson Chair plans do not require any special cutting and all sewing is straight lines. Very sturdy and lightweight, but the chair is overall a compact chair.
Thank you so much to everyone for their thoughts and prayers. My mom had a rare instance where her white blood cells attacked her platelets instead of a cold virus. The condition is fully treatable, and she is doing well. Thank you so much for thinking of our family these last few days.
Finally, not just a Parson Chair, but one that I believe anyone can build.
I choose Amy Butler August Fields for the fabric.
And stained the bases Dark Walnut. Of course you could extend the slipcover to the floor if you would like.
And my mother-in-law sewed the slipcover from my pattern. She's better at the sewing machine, and we wanted to test just how replicate-able my pattern was. What do you think? Her seams are perfect, but the pattern fits this chair like an expensive sheath.
And the best part about the pattern? Simply tuck under, staple, and attach the wood base. All bottoms seams are completely hidden.
I did promise you this chair is easy to build. Here is just how easy.
2 – 2x2s, 8′ long
1 – 2×3, stud length of 8′ long
1 – 1×3
1 – 1×2
Scrap pieces of 1/4″ plywood or No Sag Springs (also called Zig-Zag or Sineous Springs) or Jute Webbing
1 – 15 1/2″ x 17 1/2″ x 2″ standard chair foam cushion (like this one)
1 yard 1/2″ thick foam batting
1 yard burlap
1 yard decorator weight fabric
1 1/4″ and 2 1/2″ pocket hole screws OR 2″ and 3″ screws
2 – 2×2 @ 18 1/8″ (one end cut at 15 degrees, measurement to long point)
2 – 2×2 @ 15 3/8″ (one end cut at 15 degrees, measurement to long point)
1 – 1×2 @ 16 3/16″ (one end cut at 15 degrees, measurement to long point)
1 – 1×2 @ 14 1/2″ (Front Apron)
1 – 2×2 @ 14 1/2″ (Back Support)
1 – 2×2 @ 13″ (Back Base Support)
2 – 2×2 @ 16″ (Front Legs)
2 – 1×3 @ 14 1/2″ (Front and Back Aprons)
2 – 2×3 @ 13 1/2″ (one end cut at 15 degrees off square, measurement to short point)
2 – 2×2 @ 16 9/16″ (Both ends cut at 15 degrees, parallel to each other)
I’m so proud of this chair design because it does not require you to cut chair back legs. But it is very very strong – passed the Ram test. Just make sure you use glue and 2″ screws to screw the 1×2 to the insides of the 2x2s as shown above. I also joined the 2x2s with pocket hole screws and a screw from the back. It is very important to create a strong joint here.
Simply build the base as shown above. If you don’t have 2x3s, you can double up 1x3s. One trick if you are using pocket holes from the insides is to drill the holes as if you were using 3/4″ stock and use 1 1/4″ pocket hole screws. Then your front legs won’t split out. Another means of strengthening up you base is to add corner bracing by cutting 2x2s with both ends at 45 degrees (perpendicular to each other) and attaching in place. Don’t forget your glue.
Burlap and Foam
I covered my entire base frame with burlap, stapled to the underside. Trim burlap. Then over the burlap, is spray glued the foam pieces to the seat, and then wrapped the foam over the back. Notice how the sides of the back do not have foam. Trim the foam for a nice clean chair to sew your slipcover off of.
When you get the the mark, leave your needle in the fabric, but lift the foot. Turn piece A (the smaller front apron) 90 degrees so it matches the edge of the seat piece B. Stitch. If the ends do not meet up exactly, do not worry. All edges on the bottom can be easily hemmed.
Go back to the center seam and stitch the other side in the same manner.
Place the slipcover on the back and test fitting. Then pin the seat back (Piece F) to the sides and top. Start at the top and stitch downward, matching the center of the backrest with the center of the top. Turn corners to stitch sides to backrest. Fit again, letting out or taking in seams so back fits snug but not tight. See photo below.
Stain or paint bases and attach to seat.
I promise, it really is that easy!