Brookstone Desk Hutch

easy desk hutch plans
Difficulty
Beginner Projects
| Print this plan

Build your own desk hutch.  This plan matches our Brookstone desk plans.  Features three cubby shelves and space to fit most computer monitors or all in one computers.  Free step by step plans by Ana-White.com

Collections

This plan has been updated.  The original plans are still available here.

Pin For Later!

Brookstone Desk Hutch

Dimensions
desk hutch dimensions
Dimensions shown above. Works with the Brookstone Desk.

Preparation

Shopping List

2 - 1x12 @ 8 feet long

1 - 1x4 @ 8 feet long

1 - 1x2 @ 10 feet long

32" x 48" wainscotting panel for the back, or 1/4" plywood

Fastener of choice - can use 1-1/4" pocket holes, brad nails, or trim screws, or any combination

Also need 3/4" brad nails or staples for attaching the back

Cut List

1 - 1x12 @ 48" - top

1 - 1x12 @ 45-1/2" - shelf

2 - 1x12 @ 32-3/4" - sides

2 - 1x12 @ 12" - dividers

2 - 1x4 @ 45-1/2" - supports

Back is 47" x 33-1/2" - can be shorter since the 1x4 is at the bottom of the back

2 - 1x2 @ 32-3/4"

1 - 1x2 @ 48"

 

 

 

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Drill
Circular Saw
Brad Nailer
Power Sander

Instructions

Step 1

Attach top to sides with 1/2" overhang on ends.  Use your choice of fastener.

Step 2

Use the dividers to help place the shelf as shown.  Attach shelf to sides.

Step 3

Position dividers in final locations and attach.

Step 4

Add 1x4 supports.  Make sure you fasten to the bottom shelf as well for the most strength.

Step 5

Attach back panel with 3/4" brad nails and wood glue.  

Step 6

Trim front with 1x2s to finish out the front edges and add an overhang to the top.  You can build first with pocket holes and then attach, or attach with brad nails.  2" brad nails would be needed to attach the top front to the 1x12 edge.

Comments

Mardi (not verified)

Tue, 08/17/2010 - 05:50

You are amazing. I have such a long list of things to make now. Since it's 100+ degrees, I have to wait a few weeks. Keep up your great work!

: ) Paula (not verified)

Fri, 08/20/2010 - 17:39

Love, love, love your blog. Love! You rock. Love! I don't love the cartoon pin-up in this post, however. Still love your blog, gulp! Love!

Ben (not verified)

Mon, 01/03/2011 - 18:36

This is great. But I noticed almost all the plans on this website (including this one) have < 13" width's. What if we want bigger shelves? Would it make sense to get bigger boards given this design? Or should I approach it from a different design?

Guest (not verified)

Tue, 08/16/2011 - 07:29

I am planning to build the Brookstone hutch. The instructions were not specific, but it appears that (3)1X4's were used for the casing. I'm assuming 1X12's would work as well? Preference?
Thanks!

Brandon Miller (not verified)

Mon, 05/14/2012 - 10:19

I too would like the complete build and material list for this hutch but the PDF file is not working. All that is there is lot's of symbols and characters.

Kgower

Tue, 01/26/2016 - 10:09

I noticed in the supply list there are no 1x12's but the directions and cut list mention 1x12's.  I wanted to check my calculations that I will need two 1x12's at 8'.  Thanks for the help.