I have previously made side tables for our master bedroom but after two grown kids came back we had to move to the smaller of the two bedrooms we have. So here’s my 13” width version !
Nice easy build, thanks again Ana. Took longer to figure my new measurements for my cut list than actually building them!
I absolutely love the way these turned out! I drew up an example in Sketch-up using Ana's plans for the Simple Nightstand as a starting point.
This took me longer to build than I expected -- maybe because I was working from scraps and had to figure out what would fit where along the way. Also, I initially cut all the side pieces with parallel cuts. Oops. So I had to re-do them all.
For more info, check out my blog post!
I only recently stumbled upon Ana-white.com and was amazed by all of the wonderful plans and tips here, not to mention the community. My wife and I had inherited a king size bed after my grandparents passed away. While we were both grateful, the bed was on a very basic metal frame that sat very low to the ground and was hard to get up out of. My wife had often talked of having a nicer bed to put our mattress and box spring on, So with great eagerness I set to work. I loved the classic look of this bed and was a bit saddened that there was no king-size plans available. I decided that wasn't going to deter me, so I set out to modify the plan to fit. After making a few adjustments and modifications, the bed really started to take shape. Needless to say, I am very pleased with the results! Thanks everyone, and thank you , Anna!
Great plan! I curved the edges with a French curve and a bench sanding disk, and then used a router on all exposed edges. I used a dremel router table with a small bit for the small pine pieces and a full sized router for the two main platforms. If I were to do it again I’d be far more careful with angle accuracy.. I think my miter saw is a little off. My table saw was spot on for the plywood cuts. I also used smaller wheels and only have spinners on the front, preventing collision.
This is my 1st wood project and I wouldn’t have tried it without your plans, thank you!
Took about 3 weeks between work and 3 kids. (My 2 year old wanted attention and pulled down what I put up in one pic) I also made some planter boxes in the middle to complete something and a side table that slides under the couch to test the finishes on before I completed this massive entertainment console.
When I saw another builder's little bathroom tower in the brag blog last week, I knew I needed one for my powder room! Ever since we installed a pedestal sink several years ago, we've had nowhere to put extra toilet paper. With this little tower, that problem is (finally) solved!
I built it will materials I had on hand. Oak plywood I ripped to 11" for the sides and shelves, 1x2 pine for the face frame, and a variety of pine for the top glued and screwed together with my Kreg jig.
The only purchase I made for this tower was the two fabric baskets from Target for about $12, I think. The fact that they fit is not a happy accident -- I built the unit around the basket dimensions.
While it is inspired by Ana's storage tower plans, I definitely went out on my own to make it work with the materials I had lying around.
LOVed building and painting this. Although using European wood is a headache as of course the standard wood sizes are different. ... always 4-6 mm off... so all my things are crooked. I don't care though and it is my new favorite chair. I used ArchiTect blue exerior color, two coats, and pine wood.
I am grateful for Ana White's metric conversion chart in the book I now have but when going to the hardware store here, I am confronted with numerous standard wood sizes that are not the same as in the US!
Friends of mine are having a girl and needed a bookshelf for the nursery. Loved the simplicity of this design and wanted to see in an antique white finish. Great plans and design.
I added an additional detached shelf so we can change the setup anytime. I also increased the space between the two main shelves to 30 inches and extended the depth to 22 inches overall. I left one shelf off to make room for the computer tower. The top is made from maple with a gunstock stain. This desk will mainly be for my kids gaming station.
Built this for my daughter in law for Christmas. Turned out awesome. Plans and directions were great!
I built this locker system with a twist. I personalized the lockers by drilling the hooks into a cd and paint brush for my son because he is so artistic, a bone holds two hooks for my doggies' cubby, and my daughter has two hooks in a stuffed animal which represents her love for animals.
(I don't know why my picture is horizontal, it shows up fine on my computer).
In redecorating my oldest son's room, we needed him to have a loft bed, but all the commercial loft beds are too tall for his bedroom. So then, we thought we would re-work his current bunkbed. In order to use it as a loft bed we had to remove the bottom support rails and that meant we needed a new solution for a ladder (because it was part of the support system). After looking through the site, I decided that this ladder was the best for our needs. The ladder went together smoothly. We had to modify the directions just a bit to make it the right size. We put a set of U-brackets on the end of the ladder to put over the bunk bed. We also drilled through the bed frame and into the ladder for additional support.
Wed, 10/30/2013 - 12:14
Hi there! I'd like to rework my daughter's bunk bed like you did, but struggling to figure out how to raise it. I also need to build a new ladder. Can you offer any guidance on this? Thanks!
This took about 6 hours from beginning to end, but next bench should take about 4-5 hours. Most of the time was spent on sanding the wood and waiting for the stain to dry.
Main lesson learned: Drill pilot holes throughout. I used no-drill construction screws, but it didn't pull the wood tight enough against each other. Also, stain all the wood pieces before assembling (as opposed to just the top slats as suggested in the plan). Remember that the leg pieces will not need stain on the flat surfaces, just the sides that will be exposed. Use a square tool to stay as close to 90 degrees as possible.
This project was really pretty easy. The hardest part was holding the pieces just right so they ended up where we wanted once the kreg jig hole screws went in. Also, we had to be sure not to overtighten the screws and cause splitting.
We did have to make two adjustments to the plans. I think the first was a typo...where it says 2 - 1x2 @ 15 3/4" (door sides) they should actually be 1x3 based on the images.
The second adjustment was the plywood for the back 17 3/4" x 21" ended up too wide for the end to fit on, so we made it 17 3/4" x 20"
Sun, 12/24/2017 - 17:17
This was my first wood working Project! I learned alot about what to do and not to do for future projects. We are excited about how it turned out!
Love to cook, didn't have enough space in the pantry for all my spices. Used the spice cabinet plan and it was perfect.
I am starting to work on more and more projects and I'm limited with space. I needed a worktable that could double as a backyard dining table (should the occasion arise). We have been planning to build the farmhouse table for a while now, so this was a great opportunity to build a prototype. I did some repair work for a friends deck and she gave me the leftover decking material. This became my table top. I purchased 4 2x4's at our local Habitat for Humanity ReStore for 50 cents each (this was the only money spent on this project). While I was at the ReStore I also picked up 4 pallets (they are free). After cutting them apart, the 2x4s from the pallets became the table legs and the 1x4's & 1x5's from the pallets became the shelf underneath. The shelf has been great for holding extra tools while I'm working on projects. My daughter likes to stack her toys on it too! This was a super quick and easy build. My wife even suggested we just refinish it and bring this one inside!
As always, I have to give thanks to Ana for such great plans!
These are a few of my turnings. They are available for sale. Message or comment for price and shipping.
I looked around to buy a patio and found they were often quite expensive or they were poorly made out of metal that would rust. I had some scrap pine and some table legs from an old table I wasn't using so decided to make a patio table myself.
For more details, check out my blog:
http://www.woodworkingfourdummies.com/blog/patio-table
Cheers,
Ian
Modified the standard farmhouse king plan a bit. Made the headboard 4" taller and utilized 1x4's and 1x3's to fill in the headboard instead of 1x8's. I used 2x8 from front to back for the runners and horizonal 2x6's just under the lip of the 2x8 for the matress to sit on. It turned out great and we get lots of compliments.
Thank you Ana! Your plans are so easy to follow, they make me feel like a master carpenter! I still cannot believe I built this myself. I look forward to building more this year!!
Comments
Ana White Admin
Wed, 11/24/2021 - 20:50
Great nightstands!
Great mods and finish, thank you for sharing!