Flip Top Storage Bench with Cubbies

| Print this plan

I was looking for a storage bench for our playroom that had a flip top lid, but wasn't going to be a bottomless pit for tiny pieces of toys...been there done that! Then I saw just what I was looking for!  The top flips up, but the bottom is storage shelves - perfect for baskets or shoes.  

Step by step woodworking plans with diagrams, shopping and cut lists.

flip up storage bench with cubbies

I plan to top mine with a long seat cushion and some toss pillows.

Reader submitted photo

storage bench plans
18H, 45W, 17D


Shopping List
  • 1- 2x2, 6ft
  • 1- 1x3, 8ft
  • 1- 4x8 plywood - this plan was designed for plywood that actually measures 3/4in
  • hinges for lid
Common Materials
1 1/4 inch finish nails
2 inch finish nails
120 grit sandpaper
paint brush
Cut List


2 - 3/4" plywood @- 13.5" x 16" 

4 - 2x2 @ 18"

4 - 1x3 @ 13.5"



1 - 3/4" plywood @ 41.5" x 16"


Bottom and Shelf

2 - 3/4" plywood @ 41.5" x 16.25" 



1 - 3/4" plywood @ 41 1/2 x 7 3/4


Divider (you could do 1 or 2)

1 - 3/4" plywood @ 16.25" x 6.75"



1 -1x3 @ 45" (measure to fit)

1 - 3/4" plywood @ 45" x 14.75" (you might want to cut this last to measure for perfect fit)

Cutting Instructions

Sorry I planned this for 3/4 in pieces, but i realized later that if you are using plywood its going to be slightly off, but it should only be off for the lid.

Tape Measure
Speed Square
Safety Glasses
Hearing Protection
Circular Saw
Miter Saw
Brad Nailer
Power Sander
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!


Step 1

Make all your plywood cuts (see diagram)
I'm planning to get my plywood cut in-store into 2 4'x4' pieces.

Step 2

Assemble Sides using glue and 2" nails

Step 3

Add the 1x3 trim at top and bottom. Secure with glue and 1 1/4" finishing nails

Step 4

Once you have completed both sides, attach the back piece with glue and 2" nails
Make sure top edges are flush and check for square

Step 5

Step 6

Add the dividers

Step 7

add the front
Don't forget to nail from the underside of that shelf!

Step 8

Now add that 45" 1x3
Measure to fit

Step 9

ok so i think my graphic shows the lid as 14.5 wide, that was before it dawned on me that you need a little overhang to lift the lid...duh.
So it should be 14 3/4 or 15
Add the lid using whatever hinge hardware you decide upon.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. 

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.


Margy Mercer (not verified)

Mon, 12/31/2012 - 07:26

I believe a 2x2's dimensions are 1.75", so 13.5+1.75+1.75 = 16.

As for the shelf and bottom, 17"- 3/4 (the back panel of plywood) = 16.25" for the bottom and shelf to be flush with the front legs.

Does that make sense? Maybe I am wrong...?


Mon, 05/11/2020 - 05:43

Correct. 2x2 actual measurements are 1.5x1.5, so the sides actually measure 16.5" (not 17"). Assuming the plywood actually measures 3/4" in thickness, then your bottom/shelf/divider cuts should all be 15.75", not 16.5" or 16.25".


Wed, 08/31/2016 - 18:54

Beware, the dimensions in this plan are incorrect. A 2x2 is actually 1.5", meaning the width for the sides is not 17" but rather 16.5". We are having to recut all the pieces now as everything is off. The length of the top is incorrect also, not 45". So frustrating, and I guess we learned our lesson to always double check someone else's math :(


Mon, 05/11/2020 - 05:48

And the length of the top will measure at 44.5" total (41.5" + 1.5"(x2)). I'm in process of building this now, and plan to make my cuts for the top pieces last, after everything else is cut and assembled, to measure out exactly how I want them to look on the top. I may want some overhang on the sides (in addition to the front), but haven't decided yet.

Free Plans Made Possible By Our Sponsors