Loft Bed as seen on HGTV Saving Alaska

Submitted by Ana White on Mon, 09/15/2014 - 11:53
Difficulty
Intermediate
| Print this plan

Built in loft bed plans from Ana-White.com featured on HGTV Saving Alaska

Well, we still haven't heard back yet from HGTV ....   

And going through this plan is making me hopeful all over again - it was so much fun getting to work with real families, to make their home better!  

We've already shared the desk system plans with you (you can find the CPU base plans here and the bookshelf base plans here),

And today, I'm so excited to finally get to share the loft bed plans with you!

Now this should have been the easiest loft bed ever.  And it will be for you too.

Unless you live in a super insulated home in Alaska.

To make this bed easy to build, I decided to just build a mini floor inside the room (see plans following), using the studs in the walls as supports for the loft bed.

What they didn't show in the episode (and we didn't know until we started building) is the walls in this house aren't standard.  On the inside of the home, over the standard framed walls, an additional layer of 2x boards was run horizontally every 32", and then an additional layer of foam insulation placed between the horizontal boards.

That meant to tie the loft bed directly into the horizontal studs, we'd have to hang the bed at 32" (too low) or 64" (too high by the time we added the framing).  We needed the bed to be hung lower to give enough headroom.

We almost scrapped the loft bed idea ..... but at the last minute, I came up with a plan to use plywood to frame the walls around the loft bed out, making it look like we meant to wrap the walls in plywood.  You know, to protect the walls around the bed and add style points.  Not because I needed to cheat the bed down somehow  wink

Then it got easy.  We just used hangers to hang the loft bed floor joists.  Slid boards into those, topped it with 1x6s,

 

Trimmed the front out and gave it a good sanding and sealed it with clear coat,

 

And suprised ourselves at how we actually liked the bed better with the plywood surround!  

You know what they say, right?  When life gives you super insulated walls with horizontal studs, well, you make a modern loft bed!

You'll find the plans following for this project!  Enjoy!

XO Ana + Crew

NOTE: Guardrail is recommended for this bed.  

 

 

 

Can be built to any size. Standard twin mattress is 75x39 - recommend at least 48" width or a guardrail or both if needed.

Preparation

Shopping List

We used 2x4s to span about 8 feet.  For longer spans, you may wish to use 2x6s for additional support.

2 Joist Hangers per Stud and screws for hanging joist hangers

Screws long enough to attach 2x4s to studs in the wall (we used 4" screws)

1-1/4" finish nails

wood glue

Cut List

2 - 2x4 @ desired width of bed MINUS 3/4" (wall cleats)

Studs are length of bed MINUS 3"

1x6 decking boards are cut same length as wall cleats

1x6 front trim is full width of front of bed (cut to fit)

Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Drill
Miter Saw
Brad Nailer
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

Hang wall cleats securely to studs in walls, to as many studs as possible, using 2 screws per stud.  

Step 2

Use joist hangers to hang the studs to the cleats. 

For added support, we also attached the back 2x4 to studs in the wall.

Step 3

1x6 decking was then layed on top of the framing, and nailed down with 1-1/4" finish nails and glue.

Step 4

The front was then trimmed out with a 1x6 board.  We left a slight lip to the top to prevent items from rolling off bed.

 

A guardrail is also recommended to prevent injury.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Project Type
Room

Comments

dhuff44

Mon, 09/22/2014 - 19:02

If I have standard 8' ceilings, what would be a good height to hang the bed for adequate room under and above the bed?  What was the floor to bottom of 2x4 on the bed you built?

SowsEar

Mon, 11/10/2014 - 06:26

I was just doing research on this myself, since we were considering building a loft for our eldest. You can run a search via Google for "standard bunk bed clearances".  I've found that if you aim for a 28" - 32" clearance from the ceiling of your room down to the top surface of the mattress, you should be good. From there, work your way down, because the thickness of the mattress would affect, from there, where the loft would be positioned. 

 

For example: if the mattress you're using is 12" thick, guestimate that (for a 32" clearance) the bottom supports would be roughly 44 - 46" from the ceiling... which would give a clearance underneath of roughly 60". That's a little low, but still comfy for a sitting area (as long as you remember to duck when you stand up, lol).  Hope that sharing what I've found help you out!

whyNOTbuildit

Fri, 07/24/2015 - 15:18

I'm a newbie to this buiding stuff.....any plans available for the ladder for this loft bed? I like the one in the pic.  TIA!