Shoe Dresser

Submitted by Ana White on Wed, 01/05/2011 - 20:34
Difficulty
Advanced
| Print this plan

A narrow tilt out shoe storage unit that looks like a console table, acts like an entire shoe closet!

Special thanks to Niki for sharing her photo.

The boots are still there, but the shoes are gone.

It was indeed odd, seeing our Alaska entryway free of shoes and outfitted with a green dresser.

Mom, where are my Uggs?  In the dresser, honey.

Hey, that's not a dresser!

That's a shoe bin!

Yes, this is a shoe bin.  And these are the plans for it.

Someone once asked me: Why do women love shoes?   I responded "because they always fit, and when nothing else does, your cute shoes will distract from your jeans not fitting."  Have your dessert, and buy some cute shoes  :)  And build  :)

Modern Mod

If your taste is more on the modern side, save yourself some knobs and cut handles out.

This shoe dresser is designed to work with tight hallways and tons of shoes.

Dimensions
Dimensions are shown above.

Preparation

Shopping List

4 – 1×8, 8 foot length
2 – 1×6, 8 foot length
scrap 2x2s for the feet
3 – 1×2, 8 foot length
4 – 3/8″ wood dowel pins, 1 1/2″ long or two sets of traditional hinges
2″ screws or 1 1/4″ pocket hole screws
1 1/4″ Screws
2″ Finish nails
wood glue
4 magnetic cabinet clasps
knobs or pulls
A used fabric belt or strap
Finishing Supplies

Cut List

4 – 1x8s @ 47″ Door Faces (measurements differ from diagrams to conserve boards)
1 – 1×8 @ 47 1/4″ Middle Shelf (measurements differ from diagram to conserve boards)
2 – 1x8s @ 48 3/4″ (Top and Bottom (measurements differ from diagram to conserve boards)
2 – 1x8s @ APPROXIMATELY 31″ (See step 2) Sides
2 – 1×6 @ 47″ (Bin Bottom) (measurement differs from diagram to conserve boards)
6 – 1×6 @ 14″ (Approximate)
4 – 1×2 @ 47″ (Bin Backs)
1 – 1×2 @ 47 1/4″ (Cleat)
2- 2×2 @ Your Base Board + 1″ (Legs)
1 – 1×2 @ 44 3/4″ (Front Apron)
2 – 1×2 @ 5″ (Side Aprons)

Tools
Tape Measure
Speed Square
Pencil
Hammer
Safety Glasses
Hearing Protection
Kreg Jig
Drill
Jigsaw
Power Sander
Level
Drill Bit Set
General Instructions

I have marked this one Advanced not because it is difficult to build, but because it could be easy to mess up. Please don’t tackle this as a first project.

Instructions

Step 1

Door Faces

Cut your door faces. If you have a Kreg Jig™, attach door faces to make two doors. If not, that’s okay, I got you covered in the next step. Measure the overall height of the doors and take note of this. 1x8s differ from mill to mill, so be aware and build according to your board widths.

Step 2

Bins

Start by attaching the 1×6 to the bottom of the doors as shown above with 2″ screws or pocket hole screws. Use glue. Then cut your bin dividers according to the height of your doors and round corners off. Attach in place. If you did not build your door faces in step 1, you can use finish nails and glue to attach the door faces to the dividers. You can use more dividers to add more support for the door faces (and more division of your shoe storage).

Step 3

Bin Backs

You need something to keep the shoes from tipping out. How about a couple of 1x2s? Screw and glue in place.

Step 4

Box

The box needs to be build around your bins, with a 1/8″ gap around the door faces. We’ve aleady accounted for the gaps on the sides of the doors, but not the top and bottom. As shown in the diagram, figure the exact measurement of the sides and cut. Build your box.

Step 5

Step 6

Dowels

Now this is the tricky part. Not so much trick to do but trick for me to explain. Clamp the bins centered in their box, with a 1/8″ gap around all sides. If you don’t have clamps, 1 1/4″ screws could do the trick from the inside of the bins. Drill a 3/8″ hole at the bottommost front corner of your bins, careful to make sure the hole drills into the bins and does not miss the bins. The hole needs to be the depth of your wood dowels. Insert the dowels and test the bins out. Alternatively, you can use traditional hinges.

Step 7

Footer

Attach the footer to the bottom as shown above.

Step 8

The Used Belt

Have someone give you a hand, because this one is tricky to handle here. There’s only two front legs and the bins keep flopping open . . . I know Tilt the bin out to the desired max opening. Cut a piece of the belt to and screw it to the bin and the shelf below the bin. Make two straps per bin.

Step 9

Assembly

Keep the bins shut using the magnetic clasps. I used them on the sides for a nice tight fit. Screw the cleat to a stud in the wall behind the shoe dresser to keep it in place and to keep it from falling forward when the bins open.

Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

farm-marm (not verified)

Thu, 01/06/2011 - 11:27

looking at the plans...the "shelves/drawers" look like the bookcase/shelves from the inside view! he he just my randomness there...! ;)

Michelle (not verified)

Thu, 01/06/2011 - 14:33

Ana, I have shamelessly begged for this, and now it will be MINE!!

I LOVE LOVE LOVE the idea of making apothecary drawer fronts! Will be distressing the you-know-what out of it... move over Ikea and PB!!

Theresa (not verified)

Thu, 01/06/2011 - 16:53

I LOVE IT. You must be able to read minds. I have wanted one of these forever...Thank You Ana. You are terrific.

Jennifer Clark (not verified)

Sat, 01/08/2011 - 07:27

I just started this on Friday! You need to buy 5 1x8 x 8ft long. (you will have 1/2 of it left over. For the faces though I am using a 1x16x 96in paint grade panel, but I am leaving it natural. I love the checkerboard look on it.

Jenny (not verified)

Sat, 01/08/2011 - 08:54

You are a genius! Thank you so much for these plans. This is exactly what we need for our tiny entry area. My husband, who is never excited about new projects, is about this one.

Chelle (not verified)

Sat, 01/08/2011 - 16:11

I'm not sure I understand the dowel part but otherwise, I am in love with this plan. I have a TINY entryway and finding something that could fit in it is almost impossible but THIS would fit!

Chelle (not verified)

Sat, 01/08/2011 - 16:15

Also, wouldn't taller shoes fit if you put them in sideways? You wouldn't fit as many, but you could get them in there, I think.

Erin (not verified)

Sat, 01/08/2011 - 20:40

Okay, so here's the deal. I love, love, love your site and you've inspired me in so many ways...so much so that I asked my own personal Santa for a Kreg jig for Christmas and I got it! (So, as soon as my garage gets a bit warmer, I've got a long list of things I'll be building!) With regard to this shoe dresser, the problem my family always runs into is that we're tall. Seriously tall. My husband and two sons each wear size 13 shoes (and growing in the case of #2 son)...my 11-year old daughter is wearing an 8 1/2 or 9 and I stopped at a 10. These folding drawer things NEVER fit our shoes (let alone boots). So, how would I modify this to fit OUR shoes? Any advice would be greatly appreciated.

Jenny (not verified)

Sun, 01/09/2011 - 11:26

Lynzie, if you click on the image, it opens up to the whole size so you can see everything. Good Luck!