Sweet Pea Bunk Bed

| Print this plan

Free plans to build a cottage bunk bed! You can build this dream bunk bed with step by step plans from Ana-White.com. Designed and built by Jenny at Birds and Soap.

If you've got a little girl in your home, I have a feeling she's going to get a new interest in power tools after this post. That is if she isn't already! 


You already know Jenny from Birds and Soap who has engineered such amazingness as a farmhouse bed with hinged footboard storage  compartment, right?

Well, Jenny has been working on creating the perfect bunk bed system for her little girls.  

And what could be more perfect for a little girl than this?

Yes, this bunk bed is DIY!

Don't let the cute hat and pretty smile fool you, this Momma knows how to make her little girl's dreams turn into a little girl sleeping in a dream bed, DIY style!  Yes, Jenny designed, and with the help of her family, built this bed!

And she kindly wrote me asking if she could share the plans with you so you could also build a dream bed for your little ones!

This one is all Jenny, so you simply must go check out tons more pictures and her building story!

And here's from Jenny:

This bed has been a loooong time in the making. I spent the entire winter planning and googling inspiration for a bunkbed that would serve my two girls with functional storage, style, and charm that would give them childhood memories of great.  If you’ve got to share a room, it might as well be awesome, right? Somewhere along the line, Pinterest showed up and I found a great place to organize all of the inspiring ideas I found along the way. 

 I have affectionately coined this bed “The Bunkbed to End All Bunkbeds” because of the time and work invested to make it happen. While researching other bunkbed plans and pictures, I came across many a moms’ anguish over the difficulty they had when changing bed sheets on bunkbeds. I adjusted the plan so that there are a few inches around the mattress to accommodate all those layers of bedding and plenty of room to pry up the corner of a fitted sheet... It’s the little things.

This bed has a lot of little details to make it extra special. I included narrow shelves on the rear panel to give each child a space for books, the nightly drink of water they “have to have,” and an alarm clock too. The space underneath the bed will accommodate a trundle bed if needed; however, I chose to maximize storage by building three large storage boxes on casters for easy reach of shoes, toys, and little sisters (because YOU KNOW they are going to try it). They also have an optional interior box that slides back and forth on a rail for helpful organizing (shoes underneath, socks on top. BAM!)

The stairs are open concept shelving; I’m sure that drawers would be lovely, but I am still too intimidated to go “all drawer” on a project yet. It was a happy accident when I discovered that the storage bins I purchased at Lowes fit like. a. glove. into these little compartments! The shutters, window boxes, and stair railing all echo the sweetness of this charming design. While the galvanized metal “roof” over the front panel gives  an illusion of depth, I think what really takes this bed up to eleven is the pergola- because who has a bunkbed with a pergola?

 My girls, that’s who!

And hopefully yours will too! I hope this plan will be a springboard for some amazing bunkbed brags! Oh, how I wish I had little boys; I can already envision a rustic, lodgy take on this design…Wood stained siding, real tree branches for the pergola, Hunter green shutters with little Pine tree cut-outs; what little boy wouldn’t love that? Personally, I was going for a “Garden Cottage” feel for my girls’ version- but hey, whatever floats your boat!

This bed is separated into front and rear panels, which are held together by the side panels. It can be broken down rather easily to move with you. It’s sturdy! I planned the stairs to be built from one sheet of plywood. Because of this, they are a little narrow (at least my childbearing hips have noticed, haha!) They are about 17” wide; if that feels a little too small for you and yours, you might consider widening the dimensions by a few inches and purchasing more plywood.

The building process went fast. That is, after I pre-cut, primed, and painted the pieces BEFORE I assembled them. Save yourself some heartache and have a painting party before you put this beast together! I tricked my teenage nieces into coming over and helping me out which saved a lot of time. And my other advice on paint: Sample-sized paint jars from Lowes have revolutionized my DIYing, building, and crafty self! The cost of these 7-8 ounce jars is slightly less compared to a quart of paint, and allows for many color options.  I probably spent nearly fifty dollars on paint for this bed, but I was able to get over a half-dozen colors; something I would not have done had I been purchasing paint by the quart or gallon. 

I am a firm believer in distressing ANYTHING that goes in a kid’s room, because it’s eventually going to get “distressed” on it’s own. I sanded the boards on the edges, highlighted the knots and patterns in the wood by letting a little undercoat or wood show through. I thought it worked with the feel I was going for and  added to the whimsical nature of the design.

A huge, HUGE “Thank You” to Ana for making it possible for me to share this plan! Without you, I would have serial-killer-scrawled images on Post-It notes and one really messy Sketchup file! Thank you for taking  the time to make this into a visually appealing (and logical) step-by-step plan to follow (not to mention how flattered I am that it is on your awesome website). You’ve got “Mad Sketch-Up Skillz,” girl!

Seriously, Jenny, this is all you!  

This is such a large plan, we'll do the actual bed post today.  That way if you have a boy, you could use just this plan to say make a fire station bed.  We'll put the plans for the rest of the bed accessories out later this week.

Thank you Jenny, this is a real treat!

If you haven't already - you have to go visit Jenny at Birds and Soap now for lots more photos and details!

PS - this week I am traveling to shoot video for the SKIL Tool Company (yay, more video project plans!) and will be doing my best to keep up with comments and emails ... that is pending it doesn't take me several dozen takes for me to get it right and we are still filming!  #notgoodontv  

Again, a huge huge thank you to Jenny from Birds and Soap for sharing her design and photos with you! We'd love to see your bed photos when you build it, so please share!

We'll be adding plans for the roof, pergola, window boxes, shutters and those stairs later this week so stay tuned!

This bed fits a standard Twin-sized mattress (39 x 75) with a little wiggle room because changing sheets on a bunkbed can be a workout in itself. The bed measures 45x 80x 90” tall (and an extra 12” across the front if you are counting the pergola). The footprint of the stairs measure 17 ½” wide x 56” deep.


Shopping List

(16) 2x4x8’s
(20) 1x6x8’s
(20) 1x4x8’s
(12) 1x2x8’s
(6) 2x2x8’s
(10) Extra 1x4x8 or 1x6x8 boards for slats (I used half and half)
(3) boxes 1 1/4” pocket hole screws
(2) boxes 2 1/2” pocket hole screws
(1) box 2 ¼” wood screws
Wood glue
Paintbrushes or rollers

Cut List

The Bed is divided into four panels. Front, Rear, Left, and Right. The cut list is grouped into boards needed for each completed panel. Roof, Shutters, Window Boxes, and Pergola (all the bells and whistles) will follow. Cut lists for Stairs and Storage Boxes will be listed separately as well.

Front Panel

Front Panel Frame
(2) 2x4’s @ 78” vertical bed posts
(3) 2x4’s @ 77” horizontal braces
(2) 2x4’s @ 30 ½” vertical braces for lower opening
(2) 2x2’s @ 77” bed rails

Front Panel Trim
(4)1x2’s @ 30 ½” lower front panel trim
(2) 1x2’s @ 25 ½” upper front panel trim

Lower Front Panel Pieces
(6) 1x4’s @ 22 ½” lower front panel
(2) 1x6’s @ 22 ½” lower front (these will have arched cuts for window frames)
(8) 1x6’s @ 6 ¼” front lower window panels
(4) 1x4’s @ 6 ¼” front lower window panels

Upper Front Panel Pieces
(2) 1x6’s @ 77” upper front panel pieces (one will have arched cuts for upper window frames)
(1) 1x4 @ 77” upper front panel piece
(4) 1x6’s @15” window edge panel piece
(2) 1x6’s @ 17” center upper panel pieces between windows

Lower Window Sill and Trim
(2) 2x4’s @ 15” with 2 ½” x ¾” notches cut on ends, centered. Lower window sills
(8) 1x2’s @ 13” lower window side trim pieces.
(2) 1x4’s @ 11 ½” lower window top trim, arched.

Upper Window Sill and Trim
(2) 2x4’s @ 20” with 2 ½” x ¾” notches cut on ends, centered. Upper window sills
(8) 1x2’s @ 9 ½” upper window side trim pieces.
(2) 1x4’s @ 16 ½” upper window top trim, arched.

Rear Panel

Rear Panel Frame Pieces
(2) 2x4’s @ 78” vertical bed posts
(3) 2x4’s @ 77” horizontal braces
(2) 2x2’s @ 77” bed rails

Rear Panel Trim
(2)1x2’s @ 30 ½” lower rear panel trim
(2) 1x2’s @ 25 ½” upper rear panel trim

Rear Paneling
(I used leftover scraps from the other panel pieces to create a colorblock effect on the boards resting above the shelves. Instead of one long, solid board, I joined random painted lengths of scraps with pockethole screws to create one long board. This saved me the cost of four boards plus I used my scraps and it looks cool!)
(5) 1x4’s @ 77” rear panel pieces
(7) 1x6’s @ 77” rear panel pieces

Rear Panel Shelving
(2) 1x4’s @ 77” rear panel shelves
(8) 1x4’s @ 45 degrees on one end, 3 ½” on the longest side, trimmed back ½ on the short side to create a shelf bracket.

Side Panels

Side Panel Frame Pieces
(3) 2x4’s @ 38” left and right panel frame
(1) 2x4 @ 21” upper bunk opening vertical frame piece
(1) 2x4 @ 18” upper bunk opening horizontal frame piece

Side Panel Trim
(4) 1x2’s @ 22” upper bunk side panel trim pieces
(4) 1x2’s @ 49” lower bunk side panel trim pieces

Side paneling, Left and Right
(12) 1x4’s @ 38” side panel pieces
(14) 1x6’s @ 38” side panel pieces
(4) 1x6’s @ 18” upper side panel pieces near opening

Tape Measure
Speed Square
Safety Glasses
Hearing Protection
Kreg Jig
Circular Saw
Miter Saw
Brad Nailer
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!


Step 1

Front Frame

Starting with the front frame, attach the 78” vertical bed posts together with the top horizontal support. The posts will be turned in so that the 1 ½” edge is on face with the front panel. The 77” top piece is attached using 2 ½” pockethole screws drilled from the underside and wood glue on the insides of the bed posts and is also turned so that the 1 ½” edge is on face.

Next, the other two 77” horizontal frame pieces will be attached on the inside of the posts. These will be turned on their sides, with the widest face of the board facing out (on my first go round, I had them turned the other way, which gave no structural integrity to the bed rails. Don’t do that.). The middle board is screwed in and glued at 25 ½” down from the bottom of the first board, and the bottom board gets screwed in and glued at 30 ½” from the bottom of the middle board. These pocketholes should be screwed in from the back of the frame and the 2x4’s should sit flush with the front edge of the bed posts.
Last for the frame, the two vertical 2x4 pieces that will frame out the bottom opening are screwed in with pocketholes as well, each at 26” from the inside edge of the bed posts (this should leave a center opening of 25”). h

Check for level on all boards.

Step 2

Mattress Cleats 

Attach the 2x2 rails that will be used to support the mattress slats to the bottom and middle 2x4 horizontal boards on the inside of the frame. Using 2 ¼” screws pre-drilled and countersunk every 15”, and wood glue the entire length, attach the bottom rail flush with the bottom edge of the lower board, and for the middle section, attach the 2x2 rail so that it is flush with the top of the middle board. This will give a little more head room in the lower bunk area.

Step 3

Front Inside Trim

Attach trim pieces to vertical posts. Using 2 ¼” screws, again, pre-drill and countersink the edge trim into the bed posts. For the Front Panel, They are attached with the wide edge facing out and these edge pieces will be flush with the front face of the bed frame. 

Step 4

Front Upper Paneling Window Cutouts

Panel construction: Beginning with the upper portion, if you would like arched windows, you will need to measure and cut arches into this board. If you are okay with square windows you can skip this step. To figure out height and width of the arches, I used a very complicated method:

First you measure 15 3/4 inches in from the edge of your board and mark it. Then, you measure another 13 ½ inches from that mark and make a line. You now have the width of your arch measured. Do this exact same thing starting from the opposite end of the board measuring inward. The window openings will be even from the edges, and you should have an 18 ½ inch space in the center between the two marks.

Now find something big and round. I found a flower pot from something I let die hanging out in my driveway. You want a large enough circle so that you will get a slight arch and won’t be cutting too high into your board. Line your object up so that it is within your two marks and trace around it. Voila! A perfect arch!

My advice here is to cut out one side with a jigsaw, then take that scrap and use it to trace your next arch for the other window. I did not do this and my window arches ended up being slightly off, which made for trouble when I tried to make identical shutters. Bottom line: however you get your arch, whether you trace around a garbage can, pizza pan, or dreamcatcher- make sure it matches the second one. You can’t really tell from looking at my finished bed that they are uneven, but trimming it out was a real pain.

NOTE: Short panel pieces on outsides of top windows are 15" long. 15 3/4" long marks the start of the optional arch cutouts.

Step 5

Step 6

Upper Window Sills

Next you will be creating a window sill. Stand up your panel and lean it against something sturdy to work. Starting with the upper section, measure the width of you windows. If your cutting is correct, they should be 15 inches wide. Using the 20 inch 2x4 for the sill piece, you are going to create a notch on each end that is roughly 2 ½ “ long and ¾” wide. Mark your board lengthwise on center and also mark two lines at 2 ½” in from each edge. Carefully measure 3/8” out from the center line on each side and mark lengthwise.

Cut out this rectangular shaped notch with a jigsaw and dry fit into your window opening. It should lie flat resting on the board below the window space and each notch should secure it to the adjacent panel pieces. It took me a little effort to get a nice fit; a little tweaking might be required.

When you are finished, glue the sill into place on all edges and use your nailgun to secure it into position. Do this for each upper window.

Step 7

Lower Window Sills

Now for the lower windows, this is more of the same. The lower window opening should measure ten inches wide, therefore the sill piece will be 2x4x15 inches wide. Again, a 2 ½” x ¾” notch on center will complete the lower sills. Glue and nail into place.

Step 8

Window Side Trim

Trimming out the windows: The upper and lower windows are trimmed out with 1x2 material. When it came time to trim out my windows, instead of painting and precutting each piece, I chose to paint a 1x2x8 at length, cut as I needed, and touched up as I went. Due to the nature of trim work, things never seem to go perfect, and trim pieces end up a hair to long or too short so I opted to measure and cut as I went versus having too short of boards that end up in the scrap bin.

Starting with the interior edge of the window, measure the length from the top of the window sill to the top of the window opening. If you made arches, your trim will fit in that nice little ¾” space. The top windows should measure roughly 9 ½” tall and the lower window interior trim should measure roughly 13” tall. Glue the trim on either side of the window opening, keeping the outside facing edges flush and nailing into place.

Using more 1x2 material, the face trim will be added on each side of the windows. The measurements for length will be the same as the interior trim, also nailed and glued and kept flush the edge of the interior trim edge. When you are finished nailing and gluing, the sides of the windows will be secure and smooth.

Step 9

Arch Trim

To trim out the top of the windows I used a 1x4 board cut to the width of the outside trim. Again, for the upper windows, this board should be roughly 16 ½” wide and for the lower windows, it should measure 11 ½” wide. Fit it into place so it rests on top of the trim, and with a pencil, trace the arch pattern from the window opening onto the back of your board.

To get the outside arch, I measured ½” up from the bottom edge of the board and drew another arch freehanded. I tried to keep an even 1 ½” width all the way around. It is not that hard, but if you are intimidated, there is always finding another circular object to trace. Cut out both of these lines with your jigsaw and sand the edges smooth. I swear my lines were *perfect* because I’m crazy like that. But after I got went to town with my jigsaw it didn’t seem to matter much anyway; even at my best, I was all over the place ( I blame it on my blade). Needless to say, it took some serious sanding to get things nice and even.

Now if you made your windows square, things just got a whole lot easier because all you need is a piece of 1x2 cut to length.

Use glue and a nailgun secure the top trim into place on all four windows.

Boom! That’s it. Your front panel is finished! If you want to add shutters and window boxes you can add them next. I advise holding off on the roof and pergola till the end- those extras will follow later in the plan. There’s no getting through a doorway with the roof installed and a pergola hanging off the front! Take some time to look over your finished panel to make sure there are no nailheads sticking out. Use a nail set to put them below grade. Fill nail holes, sand any rough edges, touch up paint, and so on.

Step 10

Rear Panel Framing

The rear panel frame is assembled identically to the front panel. The 78” vertical posts will be attached with the horizontal top piece using 2 ½” pockethole screws and glue.

Step 11

The middle horizontal frame piece is screwed in at 25 ½” below the top piece using pockethole screws drilled from the backside of the frame and also lying flush with the outside post edges. The bottom frame will be attached at 30 ½” from below the middle piece in the same manner.

Step 12

Rear Panel Trim

Attach the four trim pieces. 25 ½” 1x2’s in the upper section and 30 ½” 1x2’s in the lower section. They should be pre drilled, countersunk, glued, and screwed with 2 ¼” wood screws so that they sit flush with the rear of the panel frame.

Step 13

Attaching the rails

Again, these rails are attached in the same manner as you did with the front panel. Glue, pre-drill and countersink 2 ¼” wood screws every 15 inches across the rails to secure them. The bottom rail sits flush with the bottom edge of the 2x4 frame and the top rail sits flush with the top edge of the 2x4 frame.

Step 14

Assembling the rear panel sections:

Now this should be really easy, after all it’s just horizontally stacked boards nailed into place. However, unlike the front panel, these boards are not broken up by center sections and extra trim. Because these panels are so long, the boards tend to be a little flimsy and want to sag in the middle. I solved this problem by using pockethole screws to join the boards on the back side.

This time, when you lay the panel down, the “pretty side” will be facing you. With your trim already in place, you can dry fit the boards to see how they will fit within the space. For the upper section, I used three, solid 1x6’s at 77” long to fill the bottom portion below the shelf. For the space above the shelf, instead of solid boards, I used scraps left over from my other cuts. I primed and painted scrap boards in four different colors, distressed the edges, then joined them together at random with 1 ½” pockethole screws on the back, giving the panel a color-block effect. This saved some money and used up a large amount of scrap that would otherwise still have been sitting on my patio. If you choose to do this, keep in mind that you want to be consistent with board size; I used 1x4 material all the way across for one row, and 1x6 material for the second.

With your boards fitted into place, remove them from the section and turn them over. Using your Kreg Jig, drill pocketholes along the top and bottom edge of your boards roughly every 15”. Alternate the pockethole placement on each row to get a solid panel. Glue and screw your panel pieces together. Wipe the excess glue before it dries.

Also, I drilled pocketholes on the ends of the boards. This rear panel is heavy!! Because of the weight of the boards, the panel almost wants to sag in the middle, so I made sure to place pocketholes along the outer edges for a solid frame attachment.

This was time consuming and I burned through 1 ½” pocket screws rather quick, but the panel ended up strong and sturdy. To attach your boards to your panel, you will need to stand it up while you secure the section with pockethole screws. Use a scrap block to make sure your boards are flush with the interior edge while you glue and screw.

For the lower section, you want to create your panel in the same manner. Dry fit your boards, drill pocketholes around the edges, and glue and screw until you have one large plank. Notice the board size on the bottom section; it is made up of (4) 1x4’s and (3) 1x6’s all at 77” long. For the color-blocking on the bottom section, I used (2) 1x6 boards, making my shelf just a few inches lower than the upstairs bunk. I did that because there is limited headroom in the lower section and figured a lower sitting shelf would be better. Totally up to you.

Step 15

Attaching the Shelf

The shelf is so simple, yet adds so much to the inside of the bed. In order to attach the shelf across the bed, I made simple brackets by cutting down piece of 1x4 and making 45 degree cuts.
Start with a board and measure 3 ½”. This measurement will be the long side of he angled piece. Adjust your miter saw to cut a 45 degree angle. You will get a perfect right triangle. Then, trim off ½” in from the point on one side, with a 90 degree straight cut. This createos a little bracket that lets a 1x4 board rest nicely on top with a ½” overhang.

Once you have made the eight brackets, find the third board down from the top of your panel. Measure 15” in from each end and mark. Attach the bracket with a nailer and glue, keeping it flush with the top edge of the third board. Measure another 15” in from the two brackets you just nailed, mark and attach the remaining two brackets for your first shelf, checking for level.

Attach the 1x4x77” shelf by gluing it to the rear panel and brackets. Use your nailer to hold it in place. Wipe any excess glue and allow it to dry.

Done! This sucker is heavy. You need a helper to move this unless you want a hernia. Keep it secure so it won’t fall over while you are working on other aspects of the plan.

Step 16

Side Panels

The side panels will go up rather fast. Instead of gluing the frame pieces together, you will just be screwing them in with pockethole screws. This way, the bed can be disassembled, allowing it to be moved inside; or if you should happen to join Witness Protection and need to flee the state, you can take it down in ten minutes flat.

Measure 25 ½” down from the top of the vertical frame pieces on each panel and mark. Do this on all four vertical posts.

Find your (3) 2x4 frame pieces measuring 38” in length and pre-drill the board ends with pocketholes so they are ready to screw on the fly (I even placed the 2 ½” screws in the holes ahead of time for lightning fast drilling action).

To put the bed together, you can either lean the panel against a wall or have someone help you hold it up while you attach the frame pieces to the first panel. The panels are heavy and can be a little bit of a balancing act before you get the first side secured; that’s why I recommend having the screws in place and ready to go.

Starting with the rear panel, attach the side frame pieces on each end of your panel so that the top of the board sits flush with your marks, drilling the screws from the inside of the bed. After these two boards are in place, attach the last 38” piece to the very top of the panel’s left post. It should mount flush with the post.

Step 17

Attaching Front Panel

Next, you will need to maneuver the front panel into position and screw opposite ends of the side frame pieces into place. When all three pieces are secured, you can let go!

Step 18

Stair Side Framing

To attach the frame for the upper wall near the top bunk opening, find your 22” vertical piece and drill pocketholes into each end. Next, drill pocketholes into only one end of the last 18” frame piece. Join the boards together at a right angle, the 22” board should be aligned vertically, wit h the 18” piece lying horizontally across the top. Take this “L” shaped piece and screw it into the upper right side panel.

Step 19

Attaching the Trim

All trim will rest flush against the outside edges of the side panels. Below the center frame support on each side panel of the bed, you will need to attach your trim pieces. Using (4) 1x2 strips cut at 49” long; pre-drill, countersink, and drill into the vertical posts with 2 ¼” screws. Remember the side panels are not glued in for this step.

Next is the trim for the upper portion of the side panels. Attach (4) 22” strips in the upper section with the same method.

Step 20

Side Panels

If your boards are pre-cut and painted, this will go very fast. Using wood glue and a nail gun, from the inside of the bed, start at the top and work your way down each side. The upper sections will use (4) 1x6 boards on each side. The left panel will be 38” long and the right will only be 14 ½” long to fit that tiny half wall. Apply glue to the back side of the trim pieces and glue between the board edges while you nail the boards into place along the trim.

On the lower sections, I alternated between (6) 1x4’s and (5) 1x6’s to fill in each side until you reach the bottom of the bed. There will be a small ½” gap along the bottom of the side panels (it serves no purpose, just too small to do anything with). Wipe excess glue and allow the panels to dry.

Note: When it is time to move the bed, you can remove each panel by unscrewing the trim pieces along each post. The panel sections will come out whole and then all you have to do is disassemble the side frame. Easy Peasy!

Step 21

Mattress Slats

I made the slats for the upper and lower bunks out of 1x4 and 1x6 boards cut at 41” long. I placed them close together (8-10” apart) and lined each bunk along the rails. Because this bed is slightly larger than a standard twin mattress (For good reason! Nobody wants to get bloody knuckles trying to change the sheets), the top bunk end slats need to be touching the side panels. When you enter the upstairs bunk, there will be a gap at the end of the bed. Make sure a board is in place to fill the space and create a little platform. For extra cool points: Paint the underside of the boards that line the upper bunk. The lucky child who sleeps below will be staring at those boards every night of his/her life before they drift into sleep. I painted the slats different colors from my leftover paint jars (and even cooler: cover the underside of the upper mattress with an extra fitted sheet- fun characters or something or other that kids like).

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.



Wed, 03/20/2013 - 07:08

I noticed that too, the 3rd or 4th picture is missing and the pdf converter is bombing out on it.
You can print to PDF though. If you don't have a pdf writer just do a google search on "cute pdf writer". Download and install it, it's free and gets the job done, I've been using it for years.
Then just right click this web page and select "Print"
Instead of sending it to your printer, choose "save as PDF" (or something simillar to that) and hit print/save
You'll get prompted for a save location and name, and click save.

I'm in no way affiliated with cute pdf, nor am I endorsing their product. I just think every little girl needs a Sweet Pea Bunk Bed. :)


Thu, 03/28/2013 - 11:30

I can't seem to find the plans for the stairs, pergola or storage boxes. Can someone please post a link or direct me on how to find them. I really want to make this for my girls.


Fri, 06/28/2013 - 00:35

I am currently working on this bed for my youngest 2 daughters. Forgive me if this has been mentioned, but what size nails did you use in your nailer for this?


Thu, 07/25/2013 - 22:07

I am so excited to make this for my girls. I can't open the PDF. Can you please send me the link to my email so I can get the plans and get started on this. You are amazing!


Thu, 07/25/2013 - 22:07

I am so excited to make this for my girls. I can't open the PDF. Can you please send me the link to my email so I can get the plans and get started on this. You are amazing!


Fri, 08/02/2013 - 20:51

what would the max weight be? can i reinforce it to hold 200lbs on bottom bunk. (if i lay with my daughter) thank you. i cant wait for my brothernlaw to build this for my daughter!

In reply to by eliseaurban


Sat, 08/03/2013 - 07:38

It should hold your weight just fine. If you are concerned, you can add more slats closer together to distribute the weight. Or you an also add a sheet of plywood on top of that. My husband who is over 2 hundo, lays in there all the time for storytime and prayers. We just have slats, probably could add more because they are not the closest, but, he hasn't fallen through yet!

I don't know anything about the PDF file problem, but someone above posted a tip on getting it to print the way you want. Good luck!


Sat, 08/03/2013 - 18:00

I was just looking through the comments again today and thought I would add something. We made all the bed slats out of extra 1x6s that we had spaced approximately 8 inches apart, and it can support my husband (306 lbs) and 3 year old (32 lbs) on the bottom bunk. Hope that helps!


Sat, 10/12/2013 - 08:48

Is there a way to get the plans in PDF since there is an error when trying to download them?


Fri, 12/27/2013 - 13:05

What would be the dimensions to make this into a toddler size bunk bed exactly like this but for toddler mattresses?


Mon, 07/21/2014 - 03:45

Hi! I am hoping for some help modifying the design slightly.

We have very limited space in our daughters room so we were thinking about using the top bunk for her bed and openning up the bottom bunk area as a school/play place instead of the drawers/bed combo.

Would it effect the design structurally if we lowered the the bottom board in steps 1 and 2 (front and back panels) all the way to floor and built the bunkbed without the bottom drawers? I saw a picture someone posted that had done this, however they didnt not tell how they modified the design.

The only flaw I can see would be that in the doorway to the school/play area the bottom board would be all the way accross the floor so the child would have to step over it to enter. Could we do away with this board all together an reinforce somewhere else?



Fri, 11/28/2014 - 21:06

Love this design and we are starting to sketch out what we need to make it happn, but quick stupid question, once you have it put together, how on earth do you get the mattress in?



Fri, 11/28/2014 - 21:06

Love this design and we are starting to sketch out what we need to make it happn, but quick stupid question, once you have it put together, how on earth do you get the mattress in?



Sat, 12/19/2015 - 21:51

This is one of the most referred-to result when looking for an awesome cool bunk-bed with a plan, and for a good reason...

Since it was made with SketchUp, would it be possible to make the file available for the eager public?

And regardless of that: I would like to thank you both so much for putting all this effort into this marvelous post. It makes me feel that even I might be able to accomplish such a feat.


Madddd Dogggg

Wed, 01/04/2017 - 09:38

Kreg seems to have a variety of Pocket Hole jigs at different price points.  Do you have a model that you recommend?

Kristi Davis

Fri, 02/17/2017 - 08:23

Do you have to put the mattress inside before you put the bed together? How hard is it to make the bottom bunk?!


Thu, 08/23/2018 - 08:02

Has anyone made this for a full size mattress? If so, how did you alter the plans so that it was still sturdy?


Mon, 09/02/2019 - 10:36

Hi.  I know.  I'm entering into a really old post.  Just wondering if the plans for the stairs and the storage were ever posted.  Thanks!