Need an amazing bed on a budget?
Build your own farmhouse bed frame with canopy with off the shelf building lumber! Our free step by step plans include diagrams, shopping and cut lists for all standard mattress sizes.
Want a bed without a canopy? Check out dozens more easy to build bed frame plans here.
Want to convert your existing Farmhouse Bed into a canopy? We have plans to do that too!

Preparation
Board | Twin | Full | Queen | King | Cali King |
---|---|---|---|---|---|
1x4 | 1 @10' | 3 @ 6' | 3 @ 6' | 3 @ 8' | 3 @ 6' |
2x4 | 7 @ 8' | 5 @ 12' | 5 @ 12' | 11 @ 8' | 11 @ 8' |
2x10 | 2 @ 8' | 2 @ 8' | 2 @ 8' | 2 @ 8' | 2 @ 8' |
4x4 | 4 @ 8' | 4 @ 8' | 4 @ 8' | 4 @ 8' | 4 @ 8' |
3/4" plywood | 48" x 48" | 48" x 96" | 48" x 96" | 48" x 96" | 48" x 96" |
1x4 Slats | 5 @ 8' | 7 @ 8' | 7 @ 8' | 10 @ 8' | 11 @ 6' |
Assumes the following mattress sizes:
- Twin 38" x 75"
- Full 54" x 75"
- Queen 60" x 80"
- King 76" x 80"
- California King 72" x 84"
HEADBOARD Cut List
Board | Twin | Full | Queen | King | Cali King |
2 - 4x4 @ | 80" | 80" | 80" | 80" | 80" |
2 - 2x4 @ | 38" | 54" | 60" | 76" | 72" |
1 - 3/4" plywood @ | 30"x38" | 30"x54" | 30"x60" | 30"x76" | 30"x72" |
1 - 1x4 @ | 38" | 54" | 60" | 76" | 72" |
FOOTBOARD Cut List
Board | Twin | Full | Queen | King | Cali King |
2 - 4x4 @ | 80" | 80" | 80" | 80" | 80" |
2 - 2x4 @ | 38" | 54" | 60" | 76" | 72" |
1 - 3/4" plywood @ | 15"x38" | 15"x54" | 15"x60" | 15"x76" | 15"x72" |
2 - 1x4 @ | 38" | 54" | 60" | 76" | 72" |
SIDERAILS Cut List
Board | Twin | Full | Queen | King | Cali King |
2 - 2x10 @ | 75" | 75" | 80" | 80" | 84" |
2 - 2x4 @ | 75" | 75" | 80" | 80" | 84" |
SLAT SYSTEM Cut List
Board | Twin | Full | Queen | King | Cali King |
2x4 Cleats | 2 @ 78" | 3 @ 78" | 3 @ 83" | 4 @ 83" | 4 @ 87" |
2x4 Center Legs | 2 @ 15" | 4 @ 15" | 4 @ 15" | ||
2x4 Top Tie In | 1 @ 38" | 1 @ 54" | 1 @ 60" | 1 @ 76" | 1 @ 72" |
1x4 Slats | 10 @ 38" | 21 @ 31" | 21 @ 31" | 10 @ 76" | 11 @ 72" |
Cut boards with a compound miter saw. You can alternately use a circular saw with guide if necessary, but do make sure your cuts are very square.
The plywood panels should be cut with a tablesaw or circular saw.
Instructions
Step 1
Step 2
Drill 3/4" pocket holes on the top and sides about 8" apart (but not the bottom) back side of the headboard panel.
Attach with a 1" space behind (and 1-1/2" space in front) to the 4x4 legs. This means the headboard panel is set up from the back edge of your 4x4 legs by 1".
Use 1-1/4" pocket hole screws to attach.
Step 5
Paint or stain the footboard, headboard and the sideboard pieces shown before moving into the room.
Drill two 1-1/2" pocket holes on each end of the top 2x4s.
Drill three 1-1/2" pocket holes on each end of the 2x10 siderails.
Move pieces into the room.
Assemble the bed with 2-1/2" pocket hole screws.
Step 6
Build the center support framing.
The twin size does NOT need any center support.
The queen and full should have one center support (as shown in the diagram)
The kings can have one or two center supports. If you are using 3/4" thick bed slats (see next step) I definitely recommend two center supports.
Step 7
Lay slats inside bed and screw down.
The mattress slats can be split to minimize material waste and also to use up scrap wood. You can use 3/4" plywood strips, any 1x material scraps, etc to fill in the slats. I don't like to leave more than 4" gap in between the slats.
You should check with your mattress recommendations for the best slat system.
It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Comments
Charleston Braces
Fri, 11/07/2014 - 07:35
Assembling using bolts instead of screws?
I was wondering if there was a way to make this with bed without using screws since I want to be able to dissassemble and reassemble it a few times over the next few years due to work related moves. I recently made a bunkbed for my boys from Ana's wonderful plans and it can be disasembled and reassembled using bolts and nuts. I worry that unscrewing and screwing will weaken the fastening over time. Or maybe there is a way to do it with hangers or straps? Of course if I could have it all, I would make it so you cannot see the bolts at all!!!
Thanks,
Sal
Charleston Braces
Fri, 11/07/2014 - 07:41
Assembling using bolts instead of screws?
I was wondering if there was a way to make this with bed without using screws since I want to be able to dissassemble and reassemble it a few times over the next few years due to work related moves. I recently made a bunkbed for my boys from Ana's wonderful plans and it can be disasembled and reassembled using bolts and nuts. I worry that unscrewing and screwing will weaken the fastening over time. Or maybe there is a way to do it with hangers or straps? Of course if I could have it all, I would make it so you cannot see the bolts at all!!!
Thanks,
Sal
lawschool_builder
Sat, 11/08/2014 - 20:20
How to Disassemble?
I was also wondering if there is a way to build this piece so that it can be disassembled later when moving? Or is it already capable of being un-screwed easily? Thank you! Also, if anyone has any modification recommendations to avoid the use of a mitre saw I would appreciate it!
-Jacq
KimDRicciotti
Sun, 11/16/2014 - 09:20
Different size plans
Do you have these plans in a double size bed? I would love to build this for my daughter!
Thanks in advance!
joecpa
Wed, 12/10/2014 - 13:20
Full size not queen
The plan appears to be for a full since the interior measurements where the box spring will go are 56" a full size mattress is 54" a queen size mattress is 60" So a queen size box spring will not sit down inside the frame.
Mtwinkoff
Mon, 01/12/2015 - 17:49
Reclaimed wall
I love the bed that you built and also love the wall in the back round And have been wanting to put a wall like that in my house and was wondering how you got all the wood in so many color variations did you use stain or just several different reclaimed woods .If you had any info that can help me I would deeply appreciate it.
ssl4847
Mon, 01/19/2015 - 06:58
saving alaska farmhouse canopy b3d
At the risk of sounding like a boob, can we receive directions utilizing 2 x 4's as well? 3 x 3 are hard to come by where I live and I don't trust myself to make the conversion in my head.
ssl4847
Mon, 01/19/2015 - 06:59
saving alaska farmhouse canopy b3d
Sorry. See what I mean? 4 x 4's. :)
Ana White Admin
Mon, 01/19/2015 - 11:37
4 x 4's
Check under "shopping list" Ana says "you could also use 4x4s, but will need to adjust the rest of the boards to 2x4s and their cut lengths"
timex10
Mon, 03/09/2015 - 20:46
bed
you don't by chance have this plan in a king size. i would like to build it for my wife as an anniversary present.