Wood Pullout Cabinet Drawer Organizer

Submitted by Ana White on Mon, 03/21/2011 - 23:03
| Print this plan

After organizing my junk drawer successfully, I felt confident and inspired to tackle some more cabinet storage.  And of course, first up, what to do with all the princess plates, lunchroom trays and sippy cups with missing lids.

How about a drawer, right at the height of a four year old?  And how about a nice deep drawer, with a big chalkboard label on it?
Of course, you could install this drawer on the bottom shelf, make the drawer have taller or shorter sides, or even put it under the sink for trash cans . . . and attach the cabinet door to the front of it for a real pullout trash can on a super budget.  There are no limits, beyond your time and your imagination.
I'm going to show you today how I built this drawer for Grace (and will probably be building more drawers for my pots and pans and maybe even one for our dog  . . . ) and you can easily modify it to fit your cabinets.  I spent about $10 on the drawer, with $6 for the 1x6 (I actually had scraps so this was free for me) and about $4 for the drawer slides.  I also used half of a 2x2, so there's another buck. I made the chalkboard label with scrap plywood and chalkboard paint and glued in on.  The drawer as shown here has not yet been finished.
pull out drawers in kitchen cabinets
pull out drawers in kitchen cabinets
pull out drawers in kitchen cabinets
Custom to fit your Cabinets


Shopping List
  • 1 - 1x6 @ 8 feet long
  • 1 - 2x2 @ 4 feet long
  • scrap 1/4" plywood 
  • 21" Drawer Slides
Common Materials
2 inch screws
1 1/4 inch finish nails
Cut List

Cut to fit your cabinets.

Tape Measure
Speed Square
Safety Glasses
Hearing Protection
Circular Saw
Power Sander
Drill Bit Set
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!


Step 1

The first thing you need to do is measure the opening of your cabinets and the depth of your cabinets. Mine had a clearance opening (the hinges took up a little room too) of 14 1/2". Remember that your drawer slides also take up 1" all for both, so that's a total drawer width of 13 1/2". To be safe, I made mine 13" wide, and cut 2 1x6s to this length. Then I measured the depth of the opening. Mine was 22 3/4" deep. So I cut the 2x2s to the depth of the cabinet and then cut the two 1x6s to this measurement minus 1 1/2" - so for me, 21 1/4". I then cut the 1/4" plywood to 13" x 22 3/4".

Step 2

With all the boards cut, I built a simple box (used 1 1/4" pocket hole screws but you could also use 2" screws countersunk) and glue. The I tapped the bottom on with 1 1/4" finish nails and glue.

Step 3

Because these cheapo drawer slides (that actually work really well and are quite strong) are side/bottom mount, you can get away with just tacking 1/4" plywood to the bottom. The weight of the drawer contents sits right on the slides. I attached the two drawer parts of the slides to the bottom of the drawer as shown above.

Step 4

Then I attached the remaining drawer slide pieces to the 2x2s as shown here. Make sure these pieces are attached level and in the same position on both 2x2s. This is important. I used the screws that came with the slides, and followed the directions on the slides.

Step 5

Step 6

Then I simply positioned the whole setup inside the cabinet, and because of the tight fit, screwed the 2x2s to the shelf from the underside. But if you had more clearance from the top, you could screw from the top too. Used 2" screws here, just two per 2x2.

Step 7

And then just put the drawer in. The drawer is easy to remove and clean (and in my case, finish) and I really love the 2x2s in there, because they keep things from sliding under your drawer. Off to build . . . six more.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.



Thu, 03/24/2011 - 15:39

Maybe because I'm in the US, the free shipping is only on orders of $40 or more.  I don't need that many slides.  The shipping for up to $20 will be $8.50.  Even though the closest HD is a ways away, it might still be cheaper for me to do that.  But I appreciate your help!

Guest (not verified)

Sat, 04/09/2011 - 09:13

We bought ours at Lowes on isle 4 last night for I think 5.50 a piece hope this helps!


Tue, 03/22/2011 - 06:49

Thank you thank you thank you!! I have been waiting for this. You are awesome. I am going to build it this weekend. You have saved me a a pile of money. Store bought ones are $100 each.

Jenny graddy (not verified)

Tue, 03/22/2011 - 06:49

thanks! I have been saving drawer slides from furniture and now can get motivated to use them for this!!

I started installing drawers everywhere..mostly the plastic storage kind or the wire kind. I like the look of these better.
I also made a mini dresser with boxes, paper mache and covered it with fabric. I know your site focuses on wood items, but since so many of boxes from all the online orders, this is a cool project to consider :)

Sarah R. (not verified)

Tue, 03/22/2011 - 06:53

I have been thinking of this very thing as of late! I desperately need an accessable drawer for my kids to retrieve their own cups, plates, etc. Awesome Ana--thanks so much!!


Tue, 03/22/2011 - 06:55

Thank you, thank you, thank you!  I have wanted to know how to do this forever!  I have been watching your site faithfully in hopes of finding just this.  (Of course, I've fought several other projects along the way, too:)  I don't comment often, so, while I'm at it; I LOVE your site, thank you so much for all you do.

Janey (not verified)

Tue, 03/22/2011 - 07:20

I have been planning to figure this out for myself for a long time now, but you've taken the guesswork out of it for me, Ana! Yay! It's actually cheaper than I thought it was going to be. My bathroom cabinets are in dire need of these drawers. Now that I think about it, the kitchen cabinet would be great with them too. Now I have no other reason to procrastinate doing it. Thank you, thank you, thank you!!! And my cabinets thank you.

cate (not verified)

Tue, 03/22/2011 - 07:30

Can you come up with an organizer for a blind corner PLEASE.  I REALLY need one.

Free Plans Made Possible By Our Sponsors