Rustic Farmhouse Headboard (Twin)

Submitted by Ana White on Tue, 08/06/2019 - 13:59
Difficulty
Intermediate
| Print this plan

A beautiful simple headboard reminiscent of an old barn door. Our free step by step plans are perfect for the beginning woodworker.

You can also build the matching storage bed frame with our free plans.

Collections
rustic farmhouse headboard with cross detailing

Reader submitted photo by  ANGELADROSE 

We love everything about this rustic farmhouse headboard.  It's stunningly beautiful on it's own.

Or pair it with our matching diy storage bed frame -

diy storage bed frame

Photo SUBMITTED BY KILE529 

Dimensions
rustic farmhouse headboard dimensions diagram
Dimensions are shown above.

Preparation

Shopping List

6 - 1x4 Boards @ 8 feet long

2 - 1x2 Boards @ 8 feet long

3 - 1x3 Boards @ 8 feet long

Common Materials
1 1/4 inch finish nails
2 inch finish nails
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Cut List
  • 12 - 1x4 @ 31" (Panel Boards)
  • 2 - 1x2 @ 49 1/2" (Side Legs)
  • 2 - 1x3 @ 49 1/2" (Front Legs)
  • 2 - 1x3 @ 38 1/2" (Back Supports)
  • 2 - 1x4 @ 38 1/2" (Front Trim)
  • 1 - 1x4 @ 26" (Center Trim)
  • 1 - 1x3 @ 44" (Top Trim)
  • 1 - 1x4 @ 45" (Top Trim)
  • 2 - 1x4 @ 30" (Cross Bracing, ends cut 30 Degrees off square, parallel)
Tools
Tape Measure
Speed Square
Pencil
Safety Glasses
Hearing Protection
Drill
Miter Saw
Brad Nailer
Power Sander
Drill Bit Set

Instructions

Step 1

Shown above is a back view.  Use a finish or brad nailer and glue to secure the back support boards to the panel boards.  Please note that sometimes boards are not exactly the correct width – you could purchase “bad” boards.  Measure your panel boards to make sure they are 3 ½” wide.  If they are not, you should cut your back support boards to fit the panel, and not to the measurement I have given above.  Adjust for square.

Step 2

Attach the 1x2 leg sides to the panel as shown in the diagram. 

Step 3

Attach the 1x3 legs to the front, as shown in the diagram.  As you nail to the 1x2 leg, keep the seam as tight and flush as possible making the legs appear as a solid piece.

Step 4

Use 2” nails an glue to attach the front trim to the panel boards, keeping outside edges flush.

Step 5

Mark the headboard as shown in the diagram.  Use glue and 1 ¼” finish nails to attach the center trim to the panel.

Step 6

As shown in the diagram, attach the 1x3 top trim to the top of the headboard. 

Step 7

Attach the 1x4 top trim to the 1x3 top trim, with a ½” overhang on all edges.

Step 8

This step looks more difficult that it is.  Cut from a 1x4 two boards with both ends at 30 degree angles (off square), ends are parallel to each other.  The board will measure 30” long, from the short point to the long point.  Then on the top side, measure 2 ½” in from the short point and cut off at a 90 degree angle.  Fasten in place with 1 ¼” nails and glue.

Help Improve This Plan

We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

Rachel (not verified)

Wed, 12/08/2010 - 07:43

I absolutely LOVE this bed. I would love to try to make it, but the PDF plans aren't loading. anyone else have that problem? Can I find the plans anywhere else?

Irma Philp (not verified)

Wed, 06/08/2011 - 15:12

Ana I really would love to make 2 of these twin size beds for my daughters who will have to start sharing a room soon and love that it has bottom storage as we can use this space for toys. Please let me know how to make it please please!!!!!

jt baker

Sun, 01/24/2016 - 14:02

I absolutely love this bed! Do you have the plans available for the bed and headboard in King size?

Would love to give this to my husband as a project for him! Ha Ha!