Rustic X Console Table

Submitted by Ana White on Tue, 05/21/2019 - 09:08
Difficulty
Intermediate
| Print this plan

Build the super popular Rustic X Console Table.  This easy woodworking project has been built thousands of times and loved the world over.  Its made of construction lumber (yes, 2x4s!) and the plans are easy to follow.  Free step by step plans from Ana-White.com.

Also in this Collection: Rustic X Coffee Table Plans, Rustic X End Table Plans and Rustic X Bench Plans

ana white rustic x console table
ana white rustic x console table
ana white rustic x console table
ana white rustic x console table
ana white rustic x console table
ana white rustic x console table

 

 

 

This beautiful rustic X console was built by Hillary from The Friendly Home.  I encourage you to take a second to stop over to The Friendly Home and read more about Hillary building this console, the finish she used, and the story behind those beautiful quilts!

 

Dimensions
rustic x bench plans dimensions diagram
Dimensions are shown above.

Preparation

Shopping List
  • 6 – 2x2 @ 8 feet long
  • 3 – 2x4 @ 8 feet long
  • 1 – 1x12 @ 12 feet long
  • 3 – 2x6 @ stud length or 8 feet
  • Corner hardware/decorative bolts
  • 1 1/4" and 2 1/2" pocket hole screws
  • 2 1/2" screws
Cut List
  • 12 – 2x2 @ 30”
  • 6 – 2x4 @ 28 1/2"
  • 2 – 1x12 @ 63 1/2"
  • 5 – 2x4 @ 11 1/4"
  • 2 – 2x2 @ 11 1/4"
  • 2 – 2x2 @ 22 1/2" (long point to short point, ends parallel, cut at 60 degrees off square)
  • 4 – 2x2 @ 11 1/4" (longest point to shortest point, long end cut at 60 degrees off square, short point cut at 30 degrees off square, angles are in same direction)
  • 3 – 2x6 @ 74 1/2"
Cutting Instructions

NOTE: If your saw does not cut 60 degrees off square, you will need to mark cuts with an angle square or compass/protractor and cut angles with circular saw or jigsaw. Practice this cut first on scraps!

Tools
Tape Measure
Speed Square
Pencil
Hammer
Hearing Protection
Kreg Jig
Drill
Miter Saw
Power Sander
General Instructions

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

Instructions

Step 1

First build two frames as shown in diagram.

Step 2

Then attach frames to shelves. NOTE: I recommend drilling 3/4" pocket holess with Kreg Jig around all sides of each shelf for attaching all shelf trim with 1 1/4" Pocket Hole screws later on.

Step 3

2x4 end supports need to be the same width as your 1x12 boards - expected to be 11 1/4" wide. Measure the width of your 1x12s and cut the 2x4 supports to match this width.

Attach to frames and shelves. For attaching to frames, use 1-1/2" pocket holes with 2-1/2" pocket hole screws.

Step 4

Add trim to the shelf.

Step 5

The X can be cut by just placing the uncut board alongside it's permanent position, and marking the overlap with a pencil, and then cutting the pencil lines with a circular saw or jigsaw.

First do the longer piece, then place inside the project, but don't attach yet.

The figure the smaller piece cuts and make those cuts.

Fit the smaller pieces in the project, and trace where they need to be joined to the larger piece.

Remove all pieces and attach the smaller pieces to the longer piece.

Then place the entire X inside the opening and attach.

Step 6

And then add the top. You can build top first with 1 1/2" pocket holes and 2 1/2" pocket hole screws and then attach to top through 2x4/2x2 aprons or just plank the top for a rustic look - it's up to you.

TIP: Just use your 2 1/2" pocket hole screws to attach the top so you don't have to go out and buy more 2 1/2" screws.

Finishing Instructions
Preparation Instructions
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth.

It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.

Comments

BuckysMom

Thu, 11/06/2014 - 17:02

Okay, I'm a new builder and I need your help!! I need this to be 6 feet instead of 8. Can someone help me change the cut list so adjust for 6 foot vs 8 foot difference? Pretty please? 

adeath

Mon, 01/26/2015 - 10:38

I used bolts and corner pieces from home depot. I used flat black spray paint from there as well. The corner hardware can be found near where they keep the latches for gates. I screwed the screws for those as well as the boost into a flattened cardboard box to hold them while I applied the paint. You can spray a little bit of the can into a film canister or medicine bottle if you need to do touch-ups once you apply it to the furniture.

davis150

Mon, 12/08/2014 - 08:44

I know with larger tables, like the farm table, there is a concern for warping once the wood dries and acclimates to the environment it is being used in. Is there a concern with this table since it is much smaller? Has anyone here had this table longer than 1 year that knows if it will hold up?