Michaela's Kitchen Island is the perfect blend of functionality and rustic beauty. Featuring added shelves, two large drawers, and a wood top, this solid wood kitchen island was built by Michaela at The Garden's Eden.
1 – 10′ 4×4 Post, Should be cheap, Untreated (you can also modify by using 2 2x4s laminated, remember the dimensions will be 3″ x 3 1/2″ as opposed to the dimensions of a standard 4×4 of 3 1/2″ x 3 1/2″ so you will need to make modifications)
14 – 1×3 Boards (About $1.50 Each)
7 – 2×4 boards, stud length or 8′ Length
1 – 1×8 board, 8′ Long (About $8.00 Each)
1 – 2×8 Board, 8′ Long (About $7.00 Each)
2 – 1×2 Boards, 8‘ Long (About $1.00 Each)
3 – 1×4 Boards, 8′ Long (About $4.00 Each)
1 – 1×6 Board, 4′ Long (About $3.00)
1/4 Sheet 1/2″ Plywood
21″ Drawer Slides
Handles or Knobs for 2 Drawers
4 – 4×4 Posts @ 34 1/2″ (Notched out for shelf stretchers)
4 – 1×3 @ 7 1/2″ (Spacers)
2 – 1×8 @ 17 1/2″ (Side Aprons)
1 – 1×8 @ 49″ (Back Apron)
3 – 2×8 @ 21 3/4″ (Sides of Drawer Housing)
2 – 1×2 @ 49″ (Face Frame Top and Bottom)
3 – 1×2 @ 4 1/2″ (Measure to fit exactly, space trim on face frame)
4 – 1×4 @ 24 1/2″ (Shelf Supports)
14 – 1×3 @ 58″ (Shelf Tops)
6 – 2×2 @ 21 3/4″ (Top Supports)
7 – 2×4 @ 60″ (Countertop)
Cut List for Drawers
2 – 1/2″ Plywood @ 21″ x 21 1/4″ (Drawer Bottoms)
4 – 1×4 @ 21″ (Drawer Sides)
4 – 1×4 @ 19 3/4″ (Drawer Fronts and Backs)
2 – 1×6 @ 23 3/4″ (Drawer Faces)
It is always a good idea to measure your finished drawer opening before constructing drawers. Most side mount drawer slides need 1/2″ clearance on each side for a total of 1″ clearance.
Work on a clean level surface. Use proper safety equipment and precautions. Always take a square after each step. Use straight and dimensionally sized lumber. Predrill and countersink your screw holes. Use glue unless otherwise directed.
2. Spacers. Begin by attaching a spacer to each of the insides tops of the legs, as shown above. Notice how the spacers will be in different positions depending on the leg. The easiest fastening method is to use your 2″ finish nails, but if you do not have a nailer, you can use 2″ screws and glue. Keep the top inside corner flush.
Side Apron. Also shown in the above diagram is the side apron (in blue). Use glue and 2″ nails to fasten the side apron to the spacers.Keep top edges flush. Check for square.
Drawer Housing. As shown above, build the drawer housing. Start by fastening the back apron to the drawer housing sides. Use the measurements above to guide you. Then attach the face frame pieces. Finally, measure and fill in the spaces between the face frame with 1x2s. You must build this housing perfectly square or your risk your drawers not sliding properly.
Top. One a clean level surface, lay out the tabletop boards. Then position the supports on top as shown above. Take great care to be exactly square, fasten the spacers to the tabletop pieces. Minimize the gaps between the tabletop pieces as you go. Leave a 1 1/2″ gap on the center, wide enough to accommodate the 2×8 drawer housing sides.
Attaching the top. To keep the top free of screw holes, lay the top on top of the island. The drawer housing sides should sit flush with your supports. Fasten through the supports into the drawer housing sides. Also fasten through the tops of the face frame into the supports. You will not see these screw holes because the drawer face will cover it. If you do not use glue, this gives you freedom to remove the top and replace or refinish if desired.
Drawers. Begin building the drawers by cutting the bottoms of the drawers out of the 1/2″ plywood. You must cut your drawer bottoms very square or they will not fit properly in your drawer housing. Then fasten the red boards, sides to the bottoms using 2″ screws and glue. Then fasten the fronts and backs to the sides and bottoms. NOTE: Check your drawer slides before constructing the drawers. Different drawer slides need different clearances, and you may need to adjust your drawer size for the slides.
You can also use any scrap 1x3s to create drawer partitions at this stage. Drawer partitions will strengthen your drawer and save you tons.
Drawer Faces. So you want your drawers to be perfectly lined up. Here’s my trick. With the drawers inserted into the housings all the way, position your faces on the drawer fronts. Leave a 1″ gap on the tops and bottoms of the faces, and a 1/2″ gap between the drawers. Then with your nailer and 1 1/4″ nails, fasten the faces to the drawers. You only need just a couple of nails. Avoid where your hardware will be placed. Then carefully open the drawer and from the inside of the drawer, use your 1 1/4″ screws to secure the face to the drawer front.
We apologize if there was an error in this plan. Please help us out and report any errors here.