Search Results
… Depending on the size bed you make, I added a couple more slats than are in the pic to hold the mattress. My dog likes to dig a "hole" in his bed so it needed support . I used 1 x 10, 1 x 12 and 1 x 8 for the … pushed in and are not attached. That way if you decide to put the bed in a different position you can rearrange the rails. My dog gets up …
Read More
Project Plan
… attach the siderails to the headboard and set in place. … To keep the bed from racking, attach the 45 degree cross bracing at the bottom. You … "legs" can be screwed to the center 2x4 to support the center of the bed. … Layout the slats on the cleats, spacing about 4" apart. Use the 1-1/4" nails to tack down. … Rustic Modern Platform Bed Frame with Headboard (All Bed Sizes) …
Read More
Project Plan
… help elevate the cleats while you work (or use clamps). … Since this bed is a full size, center support is recommended. Attach a 2x4 close to … cleats. … Measure and cut the center support. Place as shown in the bed (this is done offset to conserve wood when cutting the slats) … Cut slats and lay in bed. You can nail down (will be harder to remove later) or screw down …
Read More
Project Plan
… a 1x3 or 1x4 at the top and bottom as done in the video. … Adjust the bed for square as shown, until the two diagonals match. Secure the slats … for square before glue dries. … Attach the 2x4 blocking inside the bed for the drawer slides. The center leg does not get attached at this … - the drawers should slide very smoothly. … Insert drawers into bed and place faces on top. With an even 1/8" gap on all sides, tack …
Read More
Project Plan
… sofa feet or any other type of decorative feet in place - to get a bed like this one. Taper the 1x3s 1/2" in and 2" up for a softened look. … very important because they hold the majority of the weight from this bed. Screw legs on approximately ever 12"/ … With the 1x28 strips of plywood, cover the top of the bed. Use a chalk line to draw a line as shown in the diagram (click …
Read More
Project Plan
… will measure 82x18”. It is 2” wider than the overall width of the bed, and three inches taller than the roof frame. I wanted my panel to … frame. NOTE: You may wish to attach roof to frame before attaching to bed depending on your room ceiling height. … To install the roof, I had … screws. The four frame pieces that attached to the front edge of the bed proved to be a challenge; because of the small clearance under the …
Read More
Project Plan
… we did here: http://dateswithdrywall.com/our-diy-mid-century-inspired-bed/). For our bed, we tapered each side by half an inch at each end, starting 7.5 inches from the top of the leg to accommodate the bed frame sides (which are made of 2"x8"s). … After all four legs were …
Read More
Project Plan
… of the 2x4 cleats with 2-1/2" screws from the inside. … Lay slats in bed frame about 4" apart and screw down with 2" screws. … Camp Twin Bed Frame [Fits under the Camp Loft Bed] …
Read More
Project Plan
… boards. … Skip this step for twin beds. Mark the center of the bed between the "headboard" and "footboard" and add the center support … Measure and cut the two trim pieces. Glue and nail to the top of the bed. … Measure and cut the side trim pieces. Glue and nail to the top of the bed. … Measure and cut slats. Lay down in bed. Attach with 1-1/4" brad …
Read More
Project Plan
… Frame up the bed platform with 2x4s. Use 1-1/2" setting on your pocket hole jig to … hole screws. … Mark each of the leg sets at the height you want the bed. Then attach the bed platform to the legs from the inside with 2-1/2" screws or lag …
Read More
Project Plan