1. Home

Community Brag Posts

Oak Mirror

I recently refinished an antique oak dresser. It originally had a mirror attached to it but it was long gone by the time I bought it. My wife asked me to take an old mirror from another dresser and to build a new mirror to hang above the newly refinished dresser. I wanted this new mirror to look as if it came with the dresser which was built in the early 1900s.

The front of the mirror frame was built using red oak 1" x 6" stock. I did rip it to measure 4" wide. The mirror is 38" x 24" so I designed the frame so that a 1" lip was available to adhere the mirror to the mirror frame. The corners of the mirror were mitered at 45 degrees. I attached the corners of the mirror frame together using 1 1/4" pocket hole screws.

My next step was to flip the frame over. I then used red oak 1/2" X 6" stock which I ripped so that a 1" lip was available for the mirror. I did not miter this and I attached this using wood glue and 1" finishing nails.

I then used red oak 1/4" x 2" stock and made a frame for the outside of the mirror. This was mitered. I attached it using wood glue and 1" finishing nails. I did set the nails and fill the holes with stainable wood filler.

I then did all my sanding using 120, 220, 320, and 400 grit sandpapers. I rounded the edges a bit.

The appliques were then attached using wood glue and a few 1" finishing nails. I did set the nails and used stainable wood filler.

My next step was applying two coats of gel stain. I then applied 3 coats of fast drying polyurethane. I did some minor sanding between coats.

I then attached the mirror to the frame using mirror adhesive. Next the backing from the old mirror was cut to fit down covering the mirror within the lip. This was secured using "points". Finally the back was covered using paper and double sided tape. A 200 lb. mirror hanger was then attached. It actually contained a bubble level on the hanger. I purchased this at Hobby Lobby.

Blog Link
Oak Mirror
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Minwax aged oak gel stain (2 coats) that I applied with a brush. I wiped it off after a few minutes using a cotton cloth. And three coats of Minwax fast drying polyurethane. It was applied with a brush and I did very minor sanding between coats. I will apply clear Briwax eventually for added protection.

Note: The gel stain was nearly out and I should have added a little mineral spirits or paint thinner to thin it out some. I didn't do this and I ended up with some blotchiness due to this.
Recommended Skill Level
Intermediate

Comments

Outdoor Sectional

Submitted by rachelmlee on Sun, 01/26/2020 - 20:23

This was my first real woodworking project and was so much fun! I use my deck much more now and am excited to build more!

Built from Plan(s)
One Arm 2x4 Outdoor Sofa - Sectional Piece
2x4 Outdoor Sofa
2x4 Outdoor Coffee Table
Estimated Cost
$500 (with cushions)
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Varathane Jacobean stain
Recommended Skill Level
Beginner

We built our kitchen cabinets and hood!

Submitted by Anonymous (not verified) on Thu, 06/25/2020 - 16:50

It took us awhile but we built these white cabinets from scratch. It turned out great and looks better in person. Thank you for your articles!

Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
White acrylic latex.
Recommended Skill Level
Advanced

Comments

Eric's Cedar Shed!!

Submitted by Anonymous (not verified) on Mon, 07/06/2020 - 21:35

Thank you for the plans, shed turned out great! My association required me to match the siding color, roof color, and anchor to a concrete slab. So I poured 25 bags of 80lbs concrete to make a 9x5 slab. Redid the plans for an 8x4 shed, built the frame with 2x4s and not 2x2's, installed flashing, ice/water shield + felt + matching shingles since I'm near Chicago, and used a flexio finishing sprayer to paint the shed. Saved some $ by using 2 Redwood Grain Fiber siding panels for $22 each at HD.

All in all very happy with my shed and all my dangerous yard tools and woodworking tools can be put away from my toddler.

Built from Plan(s)
Small Cedar Shed
Estimated Cost
400
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
Behr Premium Plus exterior paint
Recommended Skill Level
Intermediate

Converted TV wall niche

Submitted by Vol4Life1 on Tue, 12/13/2016 - 05:35

We bought this house about a year ago and we finally got around to removing this pointless niche!  The center divider and bottom were removed.  The cabinet and hutch were assembled seperately.  

 

This is still a work of progress.  I am looking for a nice decorative molding face for the top.  If anyone has any suggestions please let me know!  We will most likely paint it white to match the fireplace mantle.

Estimated Cost
300
Estimated Time Investment
Week Long Project (20 Hours or More)
Finish Used
Paint
Recommended Skill Level
Intermediate

Cedar planter

Submitted by Shayed on Sun, 09/07/2014 - 11:55

I used your "cedar planters for less than $20" plan and modified it to create two beautiful planters for my house. I framed out the top of the planter to give it a more complete look. Also, I added a "C" for our last name. -Shaye 

Built from Plan(s)
Cedar Planters with 2x2 Legs
Estimated Cost
$20, I used a lot materials I had on hand.
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
mahogany stain
Recommended Skill Level
Beginner

Jewelry Organizer

Submitted by CSaintD on Wed, 04/01/2015 - 10:20

I really didn't have a plan for this, but looked around on this site and on the internet and found something like what I wanted to do, so just made a simple frame out of scrap 1x2s.  I made a groove in the center of each 1x2 with my table saw before assembling.  I found this pretty punctured metal at Lowes and cut it to size, slid it into the grooves then attached the bottom of the frame and the little shelf.  I added a 3/4" bead and sausage trim piece around the whole thing to finish it off nicely.  The bracelet holder is a dowel rod that I painted purple and attached with eye hooks and cup hooks to the bottom of the little shelf.  Since it was hard to put earing studs in the center (with the backs on), I also cut another piece of the metal, filed down the edges and attached a llittle ring clip, that can hang from one of the cup hooks if needed.  I'm happy with how this came out and I hope my Daughter-in-Law will enjoy this birthday gift.

Built from Plan(s)
Farmhouse Jewelry Wall Cabinet
Estimated Cost
The metal was the most expensive part at $26 for a 2' x 4' sheet. You could do this with hardware cloth for a lot cheaper, but I wanted the look of the metal. The trim was $5 and cuphooks $3. The other pieces I had in my scrap pile and hardware drawer.
Estimated Time Investment
Day Project (6-9 Hours)
Finish Used
White gloss paint and purple craft paint. Spray lacquer on the dowel rod.
Recommended Skill Level
Beginner

Comments

CSaintD

Wed, 04/01/2015 - 18:23

Yes, I was trying to imagine some way to do what you suggested, but just couldn't make it work. I didn't want to make a door - which would be the ideal solution. Also, fiddling around with the frame may make it unstable on the wall, so I just thought this would be easier. She can lift the whole thing off and add and remove studs at a comfortable height without worrying about removing necklaces, etc.

Changing Tables for Granddaughter and Grandson

Submitted by Anonymous (not verified) on Fri, 10/08/2021 - 08:50

My wife and I were expecting two grandbabies (a boy and a girl) in the Fall (about 2 to 4 weeks apart). We were asked by one of our Daughter's-In Law to make a changing table. We decided to do it for both grandbabies. These photos represent the result of the inspiration we got from Ana White's changing table design on her website. We liked the basic design but wanted it to have a shiplap look. We also wanted the top drawer to be a full drawer across the top and the middle shelf to be a pull out shelf with a drawer front. We were ecstatic with how they turned out, and so were the parents!

Built from Plan(s)
Baby Changing Table with Drawers and Topper

Comments

Wife's Kindergarten Classroom

Been a while since I had time to actually build anything worth posting about! My wife wanted some items for her Kindergarten classroom this year, so built several items, most inspired by the Farmhouse family.

Estimated Time Investment
Day Project (6-9 Hours)
Recommended Skill Level
Beginner

Comments

sido17

Thu, 07/18/2019 - 15:27

I would love the dimensions or plans for this. Would love to make it for my classroom.

dlee69

Tue, 07/30/2019 - 12:07

Hello

Can I please get the plans to the u shape table?

Thanks

Linguine

Mon, 08/19/2019 - 12:09

I am guessing the corner posts are 2 x 4s, the top is 2 x 10s.  It looks like the width is 6’ (looking at the floor carpet tiles being 24” square). So 2 - 2 x 10s side by side for the main part of the desk top and 2 - 2 x10s perpendicular on each side of the chair.  I guess the height is subject to choice and the length of each side would also be subject to choice or to the length of the 2 x 10s to be economical.

 

an educated guess would be 4 - 8’  2x10s for the top and 6 - 6’ 2 x 4s for the legs?  

 

Anyone else have any input here?  Open to suggestions.....

Platform Bed with Shoe Trundle

Submitted by vendo on Tue, 11/22/2022 - 08:08

We had some bulky items that needed to be stored. So I came up with dimensions for a low platform bed so the bows could slide under. I decided to build a faux drawer to conceal the bulky items and added shoe storage into the faux trundle drawer. Of course I used one of Ana's plans for the basic idea and modified from there! 

bed with trundle storage bed

bed legs

bed frame 2x4

inside bed frame

bed support

Blog Link
Family DIYnamic
Built from Plan(s)
Daybed with Storage Trundle Drawers

Rustic Computer desk with Shou Sugi Ban and Epoxy Top

Submitted by Anonymous (not verified) on Tue, 03/14/2023 - 14:16

I slightly modified the Rustic X Desk plan to make my L shaped computer desk with a monitor platform! The desk surface is Shou Sugi Ban with an epoxy finish. All made from stock lumber and a lot of pocket hole screws. Thanks for posting your plan Ana to give me the idea! Construct for around $200.

Built from Plan(s)
Rustic X Desk

Comments

Sliding Door Console

I modified the plans to have three compartments instead of four. Also, the hardware was a challenge.  Tip: use a wheel that has an internal bearing. 

Built from Plan(s)
Grandy Barn Door Console
Estimated Cost
$200.00
Estimated Time Investment
Weekend Project (10-20 Hours)
Finish Used
pre-stain and golden oak by minwax
Recommended Skill Level
Intermediate

Cubby Organizer (Pottery Barn Inspired)

This cubby organizer is great for storage, displaying collectibles or as an advent calendar. I'm using mine in my mini-workshop for storing tools and supplies I use frequently when woodworking. Tutorial can be found at my blog here: http://betweennapsontheporch.net/build-a-cubby-organizer-pottery-barn-i… Thanks Ana for supplying the plans!

Blog Link
Build a Cubby Organizer, Pottery Barn Inspired
Built from Plan(s)
25 Cubbies on the Wall
Estimated Cost
$40
Estimated Time Investment
Day Project (6-9 Hours)
Finish Used
I used Sherwin Williams Dover White paint for a soft white. Stain would work great for this piece, too.
Recommended Skill Level
Beginner

Rolling saw horses

Submitted by Craig P on Mon, 07/04/2016 - 07:26

Your saw horse plan worked great for a wooden boat project I'm doing -- the 3" wheels (with one locking) enable me to move the boat around the workshop or even outdoors for heavy duty sanding. 

I added blocks of 2x4 to the legs for more surface for the wheels and I extended the cross pieces to 4-feet long as the old AuSable River (MI) guide boat is about 40" wide.

Built from Plan(s)
Easy Heavy Duty 2x4 Sawhorses
Estimated Cost
$60.00 (a lot of the cost is in the 3" wheels..)
Estimated Time Investment
Afternoon Project (3-6 Hours)
Finish Used
None, though thinking about putting some finish on them as they'll be getting wet when I wash down the boat...
Recommended Skill Level
Starter Project

Comments

Custom Toy Box

Submitted by Anonymous (not verified) on Sat, 04/27/2024 - 11:30

Your plan for this toy box was sooo easy to follow, but I added the feet. My grandson loved it. I have 2 other projects from your plans for him as well.

Charlene

Built from Plan(s)
Farmhouse Toy Box

Beer carriers

Submitted by Anonymous (not verified) on Thu, 04/20/2017 - 15:23

I love the vintage look with old license plates.  @theshopbycecilia

theShop-woodwork and design

Estimated Time Investment
An Hour or Two (0-2 Hours)
Recommended Skill Level
Starter Project

Rustic Adirondack Bench (love seat)

I loved the Rustic Adirondack Chair so much I felt I needed to make a bench in the same style. I had to be a little creative with the chair plans and modify them to make my bench work. I am absolutely thrilled with how it came out! I already have a friend who has requested a chair and bench (love seat) for his son's wedding gift!

Built from Plan(s)
Modern Easy Build Adirondack Chair
Estimated Cost
Material costs for the wood was $85-ish. Wood prices are nuts right now!
Recommended Skill Level
Intermediate

Comments

mjackson41995@…

Fri, 08/20/2021 - 16:37

You can make the 1x10 in any length you want. I’m planning on making a loveseat too and The measurements I chose for the seating area will be 48” long (which is the size for 2 seat cushions).

The Step 1 in Ana’s plan, all measurements will be the same.

Step 2: The two 2x4 horizontal supports will be cut at 48”.

Step 3: the two 1x10 seat panels will be 3 inches longer than the horizontal supports. So you will cut the 1x10 seat panels at 51”.

Step 4: Instead of two, you will need THREE seat supports. So cut three 2x4’s @ 32 3/4”. The third seat support will go in the middle of the other seat supports, drilled to the horizontal back support.

Step 5: Attach your back bottom horizontal support which will be a 2x4 at 48”.

Step 6: Attach the 1x10 seat back panels. You will cut (3) 1x10 @ 48”.

Here is the cut list for the loveseat version of Ana’s Adirondack plan. These are the lengths I chose. So with this cut list your loveseat should be big enough for two 24x24” seat cushions. I plan to add cushions for extra comfort.

My cut list:
(2) 2x4 @ 31 3/4”
(2) 2x4 @ 19 1/2”
(2) 2x4 @ 33 1/4” Cut at 20 degrees as per Ana’s plan.
(3) 2x4 @ 48” Horizontal supports. One goes behind your calves.
The other connects the end frames/arm rests at the back.
(2) 1x10 @ 51” Seat panels.
(3) 2x4 @ 32 3/4” Vertical supports for the back panels.
(3) 1x10 @ 48” The back panels.