Adirondacks
These a few of your designs I’ve created. The bench and Adirondacks were the fist of my Covid projects, then I added the outdoor living space landscaping… sorta. Thanks for Great plans. I love making the stuff.
These a few of your designs I’ve created. The bench and Adirondacks were the fist of my Covid projects, then I added the outdoor living space landscaping… sorta. Thanks for Great plans. I love making the stuff.
This was my very, very first woodworking project. My daughter and I needed beds, but decided to start small. I’d been scoping out Ana’s plans for weeks or maybe months, and finally, finally worked up the nerve to tackle a project. Everything worked out beautifully. Somehow, I’d been intimidated about the idea of learning how to countersink screws, but with Ana’s directions it was easy! I did get a measurement wrong somewhere and after cutting all the wood, the 5 1×3′s for the panel were too wide for the panel top, so instead I spaced out four of them. My daughter has never liked dolls, so I made the bed thinking that it would be a gift for someone else, but my daughter really, really liked it and wanted to keep it. Now the doll bed lives at the foot of the full-sized bed that we made as our second Ana White project! Now if I could only figure out how to sew a doll-sized pillow… Thank you Ana for making this simple.
I used a pallet I found in a burn pile, cut it down, added a bottom piece from one of the other cross pieces, painted, stenciled, and covered it with a coat of poly. I then added potting soil and herbs, and screwed it into the studs of our porch. It's off the ground so my dogs can't get into it and my chickens won't sample the plants!
This is a customized version of a farmtable that my wife found here!
Sun, 04/12/2020 - 10:51
how do I get plans for this table? it is the customized farm table, thank you
I felt a little bold deviating from the plans when this was my first project. But I saw another version of this desk with the breadboard ends, and I really appreciated the added craftsmanship this gave off. Other than the top, I followed the plans to a T. For the top, I made this from 2x6's with the 4 lengthwise pieces cut to 61" and the ends to 22" (I think I ended up trimming the ends down to match better, but 22 was a good starting point). As for the finish, I layered stains starting with Minwax's Classic Grey followed by Minwax's Jacobean. I made two of these desks to put in our home office. If I think of it once the office is complete and decorated, I'll add another pic!
I wanted a kitchen island that would match my farmhouse table and would fit in my small kitchen.
I had SO MUCH FUN building this play kitchen. I looked at all the different play kitchens on the site and took what I liked. I love bead board and I LOVED the oven light idea. I’m 7 months pregnant and was still able to put this together. My lower back was starting to complain by the end so it is good I finished it up when I did. I used a kreg jig jr. instead of a nailer. For this project I wish I had a nailer, I think it would have been easier. Maybe I’ll get one for Christmas! Up next – the cabin collection!
I needed a way to display some old pictures... I just love the look of old pictures and and wanted something different than an ordinary frame.This is one of the easiest and cheapest picture display project you can do.
A full tutorial can be found at www.AHouse-2-Home.com
Feel free to leave a comment on our site, we greatly appreciate them!
I built this Workshop Step Stool as part of the #GetBuilding2015 #BuildCave challenge. It was a very easy build. I had all the needed supplies in my scrap wood. But if you did need to buy the wood, you could do it for under $10.
I found the plan here. http://www.familyhandyman.com/workshop/ridiculously-simple-shop-stool-p…
If you want to see the steps I took to build mine, as well as more pictures, please stop by my blog at http://jaimeofalltrades.blogspot.com/2015/04/diy-workshop-step-stool.ht…
My husband calculated the dimensions to extend the plans from a queen to a king size bed. It was our first project together and we're both really excited about how it turned out!
Those are the first projects that I try to make. Thank you Anna White .
This is my third Ana White project and I modified it quite a bit from the plan. I was inspired by the PB Logan Collection that Ana has a knock off plan of called the Classic Storage Wall and Hutch. You can read more about the whys and hows of this project on my blog pinktoesandpowertools.wordpress.com in the Cabinet and Hutch-laundry room category under woodworking (there are currently 17 posts about this project--yowza!). But the modifications that I made from Ana's plans were that I had to make it less wide, I added two drawers in the cabinet, and I put a back on this that mimics the PB picture (which happens to be the wall behind their open-backed units, not an actual back). The base also hides a cat litter box behind it, so the back is open and the doors do NOT open--they are a fake front. No need to peek in at a litter box and it eliminated the cost of hinges. I learned A LOT during this build! First experiences were: using a circular saw, making a straight cut jig for a circular saw to cut plywood, using a jigsaw, using a compressor and nail gun, cutting crown and base molding miter cuts, tearing out base molding to fit the cabinet, cutting out an electrical outlet in the cabinet and extending the outlet, learning how to remove pneumatic nails that find their way out to the front of your project, and probably more that I can't think of now! The back isn't quite done, but it won't be too much prettier than what the picture shows, and you can see how the litter box looks. I might turn it sideways and cut out a hole in the side--haven't decided on that yet... I am really pleased with how this turned out and I'm excited to start on my next Ana White plan (probably modified, knowing me!).
Using Ana's plan as a guide, I built two of these sofas to fit an outdoor cushion I already had. I used wood from our old deck -- a great way to re-use and save money, too!
Fri, 05/01/2015 - 10:20
Looks relaxing and wonderful! Thanks for sharing!
Mon, 05/11/2015 - 03:24
Ok, I was thinking of just how great these chairs would look around a fire pit.... and then I seen this. I may have to talk my husband into this for a summer project! Great build. Love the bright colours! And the poochies are cute too :)
Wanted to make a loft bed for my 4-year-old son's room that could accommodate a toddler bed beneath it for when my 1-year-old daughter eventually starts sleeping on her own. I was torn between the Chelsea and Cabin bed plans, but eventually settled on the Chelsea because I liked the look of the headboard better.
I looked through all the brag posts to get modification ideas. I ended up mostly stealing ideas from "chadwickstafin", and like him took the great idea from "groovymom2000" to use chalkboard paint (though I only used it to paint the side of the desk end, since I knew the bookshelf end would be mostly blocked by a ladder). I decided to skip the decorative feet and just extend my 2x2s to the floor for extra strength, a mod that most people appear to be doing with this plan. I saw some people using 2x3s in place of 2x2s for added strength, but I can confirm that 2x2s are plenty strong enough on their own (2x2s are stronger than people give them credit for, and there's 8 of them here to distribute the load).
Like chadwickstafin, I cut my headboard a little differently, and I used short lengths of scrap 2x2s cut at 45-degrees to brace the top and bottom corners of both end units. There is no wiggle to the bed at all, it's stabilized so well. I also added a middle support to the short rail, just for a little extra safety, and secured the inside ends of the railings to the headboard/footer with pocket screws. I skipped the filler pieces for the railing, and just did a little extra sanding to make sure all exposed corners were smooth and splinter-free. I made the opening to the bed a bit wider than the plans, 15" instead of 13". I used 2x3s for the ladder, which gave me the sturdiness I wanted without the full bulk of using 2x4s, which looked especially chunky next to a loft unit made with mostly 1x boards. I played with some different angles, but eventually went with a 15-degree ladder. There were some leftover plastic handles sitting in my garage (originally from an outdoor playset ladder before I replaced it with a climbing wall), so I added those near the top of the ladder for some extra safety. I put some color-changing strip lighting under the bed, so there would be plenty of light for the desk and bookshelves (my little guy loves to just plop down on the ground beneath his bed and read).
I spaced the 1x3 slats about 3.5" apart (used scrap 2x4 blocks as spacers). Because my wife or I will lay in bed and read to our son at night, I easily added a couple 2x2 support rails under the 1x3 slats for extra mattress support. I'm a big dude at 6'3 and 250 lbs, and the slats alone WERE strong enough to hold me when I did a test, but they bowed just enough in the center (unnoticeable to me up on the mattress, but I had my wife watching the slats for me below) that I felt I should add a bit more support. Now there's no bowing at all.
I also used Ana's Top Bunk Organizer plans to give my son a little extra storage up top (and a place to set a glass of water during the night), and painted it to match the bed's color scheme. Everything was sanded, painted, sanded again, repainted, and then given a couple coats of polycrylic (the painting process took longer than the cutting & assembly!).
Cost-wise I was extraordinarily lucky. We have a Habitat For Humanity ReStore near us, so I was able to get my paints and a 3x6 sheet of MDF for $15 total. I also had some rebate cards from Menards (regional hardware store, similar to Lowes or Home Depot), plus happened to go there on a week when pine wood was on sale, so I got all my lumber for less than $60.
I could not be happier with the end results, and my son absolutely loves his new bed.
This was my first big Build! Thank you Ana for the free and easy to read plans.
My first "real" project!
We are in desperate need of toy storage in our playroom. We are planning to build several more of these bulk bins.
Mon, 05/04/2015 - 10:59
You did great! Thanks for sharing, now fill those things up:)
Sun, 11/20/2016 - 10:39
It was just standard pine. We painted afterwards with grey paint leftover from a kitchen project.
Hello, fellow makers!
I really enjoyed this build - it was a challenge for me, but in the end, I'm thrilled with the results!
I modified two of Ana's plans to come up with this storage bed and I share more pictures of the process and how I finished this project over on my blog Tinsel + Wheat.
I used the Twin Bed Farmhouse plans to create the headboard and footboard, which turned out beautifully, but because of the storage base needing to be installed flush with the edges of the 4x4 posts - this made the bed a little wide for a standard twin size mattress. I don't mind the extra 2.5" of base on each side of the mattress but if you decide you would rather have the mattress edges match right up to the bed you will need to subtract one of your center 1x6 panels from both the headboard and footboard. This will give you the perfect size headboard and footboard for this build.
So grateful to Ana for these plans!
Happy building!
Miranda
Sat, 03/02/2019 - 10:02
Might you have the lumber shopping list for the storage boxes to go with this modified Twin Farmhouse with storage bed? I looked at you personal website but you just have the cut list for them not lumber list. Desperate need to purchase my wood Monday.Thank you so very much!
My wife wanted some planters for the front porch. Thanks to Ana whites page for these plans. Also loved the top modification that I think is a must.
Comments
Ana White Admin
Wed, 10/06/2021 - 10:30
Wonderful projects!
Thank you for sharing, it all looks very pretty and inviting!