Community Brag Posts

I used the Rekourt plans for the most part, but I did change it a bit. I needed a smaller table, so I adjusted the plans to accommodate this. The table is 5 feet long with matching benches that are 4 feet. I eliminated the 2nd cut on the 2x4s used to construct the table base to simplify the look. I also made custom benches to match, as I could not find any plans that were an exact match on the site. This is the first time I've built anything, and it took some trial and error and a lot of muscle. It was well worth it though!

We needed to organize in the laundry room. This was the perfect idea.

This was a project to use some pieces of left over ¼” thick aromatic cedar closet lining board.  I cut off the tongues and grooves with the sliding miter saw, and calculated the measurements for the box to fit the size of the wood.  For this build I used the micro-pin nailer with compressor, and ½” headless pin nails.  The finished box measures 4 1/8” tall, 6” long, and 3 3/8” wide.

Inside, a divided lift-out tray sits on rails made from small pieces of the cedar board glued to the inside.  The addition of an extra decorative board to the top made it ¾” thick, to work with a regular knob.  The inside of the box stayed unfinished to preserve the cedar fragrance.  This was an afternoon project.

I've wanted to build one of these forever! I changed the plans a lot to accommodate my needs, but I loved the idea of faux drawers on the doors to have an authentic look. It fools most people! Took 2 weeks for me to complete, working on and off. It has great storage inside for all the kids' stuff I didn't have a place for previously. The stain is ebony by minwax and the hardware pulls I purchased for under $10 for 30. 

I built this bookshelf for my husband's office. He wanted a shorter, wider shelf than the original plans, and this is what I came up with! :)

This was just a quick little project as we decided we needed a bit of organisation in the office.

I just used scrap mdf and leftover bits and pieces from other projects for this wall file. We now have somewhere to put all the postage stuff for our online sales site.

Cheers... Nay

Our son Liam-Joseph wanted a "Big-Boy Bed" and then he added "I want Daddy and Santa to make it".  Well "Santa" and my wife Jacques looked all over the internet and finally found your Cabin Bed via jennwoodhouse.com.  Jacques altered the plans demensions and she realized the bed could be barn-like so she came up with the red and gray paint job.  She actually wanted a cupola but I thankfully talked her out of that.  Well somehow we keep the construction from Liam 2 weeks before Christmas.  On Christmas Eve Liam's Grandparents keep him at their house while "Santa" and I put the bed together (I never did a trial run so I was relieved when everything fit right together).  The next day after opening his presents he ran up to his room and saw his bed for the first time.

The project isn't completed.  I recently finished the roof with wood pallets but I need to finish the trimming of the interior of the bed walls.  

We used carraige bolts to make the legs removable. Very happy with the results!

My wife and I completed our son's loft bed in December for his Christmas present. My wife found this bed on Pottery Barn's website and I found these plans on Ana White. Everything was pretty straight-forward. It was a great project and we had a lot of fun building something together. We made a few mods to the plans like height and the railings. I really like how it comes apart for moving and our son loves sleeping up there! Protip: Be careful with the wood glue where the bed is designed to come apart. I got a little sloppy and had to do some hammering to disassemble for staining/sealing. Everything went back together very easily, though.

I've been organizing our unfinished basement so that my boys have more space to run and ride their bikes over the winter. I needed something to organize our off season clothes and bins of clothes that my boys are growing in/out of. This plan was perfect. It's not my prettiest build but it's soooo functional!

Fun and easy project. I couldn't be happier with the end results. Great plan from Ana White. 

Using the plans for the modern table and simple stools, I made some modifications so it could be a bar height pub table and stools. The stools took the most time, with all the supports and keeping it level. The table was easy and I am super happy with the addition of the x's on the sides. I think it gives it a more professional look. Turned out that the angle I wanted them at wasn't possible on my miter saw, so I just had to mark the angles and cut with a jig saw. Screws were overkill for them and split the wood, so finishing nails did the job. The top was salvaged from an old ugly mdf topped coffee table. I sanded it a bit and with many coats of stain, achieved a match to the rest of the wood. Yay! Breakfast nook, complete!

Hey all my DIY friends!

This is my first build of the Rekourt Dining Table.  Big thanks goes out to Ana and Jen for providing these awesome plans.

I think I achieved this table quite well, except for a minor detail where I forgot to sand two pot holes.  It actually created a very rustik look to this table.  I decided to try the steel wool and vinegar solution combined with the black tea for the finish of this table.  I realized it adds so much richness to the wood, it's incredible.  The stain is Minwax's Dark Walnut and I topped it off with a Satin Oil-based Polyurethane.  The top and legs were also physically distressed using a variety of tools I found in my tool chest. Those included screw drivers, lag bolts, worm hole puch I created out of a leftover 2x4, chains, sanding disc, knife, hammer and much more!  That part, although tedious, was fun as it gave me the permission to bang stuff up intentionally :)

For the finish, I first started off by sanding very well, talking hours for the entire table. I then went out and distressed the tops in a very random fashion, trying to not repeat any patterns.  As I was doing this, I was waiting for my black tea to seep and be ready for application.  I poured boiling water in a large Mason jar and added 4-5 bags of black orange pekoe tea bags.  I waited about 2 hours before applying it with a foam brush, very liberally.  I allowed the tea to dry overnight and the following day, I applied the steel wool and white vinegar solution. My solution had been sitting for about 5 days, enough to start seeing a bit of rust in the Mason jar. The rusty solution ended up giving the wood an orangy/redish tone, which when seen under the dark walnut, added lots of depth and richness to the color.  Once dry and the wood had turned greyish/orangy/redish, I stained it using Minwax's Dark Walnut stain.  I did section by section, leaving the stain no more than 3 minutes before wiping dry.  I followed this (once the stain was dry) with two coats of oil-based polyurethane in satin (Varathane (Canada's version of the Rust-Oleum poly). I sanded the poly in between coats with 220-grit sandpaper using my orbital sander.

Since then, I have gone out to build about five of these, all in different lengths and sizes, including some with removable bases. The angles in the X's are a little tricky when you don't have plans for a specific size, but I have noted these down based on spacing between legs.  If any of you need andgles for specific table lengths, let me know and I may be able to help :)

Let me know what you think and happy building!

Made two of these fabulous kitchen helpers! One for my niece and one for my own active 2 1/2 yo daughter. She loves to bake with me and is always underfoot while I'm cooking dinner. This has made her so independent, she gathers her own supplies and pushes it around the kitchen to reach whatever she needs. Came out of the shower to find her scooping ice cream into her bowl for breakfast... Thanks Ana!

We could not find a large enough coffee table that we wanted so we decided to make our own.  We loved the Rustic X plan and thought if we put two tables toghether we could get the pefect table size for our living room.  Project cost us around $120 and it took us a week to complete, but we are happy with the results.  The color is a dark expresso.