Community Brag Posts

This is my very first project! I had so much fun building this for my son. His room wouldn't fit the stairs so I modified the ladder so that it was inclined to make it a bit easier to climb and less scary for him. This was such a fun project to take on. Thanks Ana for the plans!

I modified the original plans to fit the height and length of my sofa as well as to show off the chevron planks. I was offered some pallets...so, I greedily accepted them, to which my husband rolled his eyes and sarcastically said, "Great, more wood!" I tried to make all of the table from the pallets but I ended up using pine for the table edging and the "X."
I laid out the table top in a chevron style on 1/2in plywood, glued and screwed them in from the bottom with wood screws. I attached edging with pocket holes. For the bottom part of the table, I attached larger pallet boards using glue and pocket holes instead of attaching to plywood. I actually attached the edging first to the bottom boards and then attached to the table rather than attach the bottom edging and then try to make the boards fit. I sanded the top and bottom tables with 40, then 80, then 120, and then 240 grit sand paper until smooth. I also sanded the legs the same way. To say that total time sanding for the entire project was 20 hours maybe an understatement. If you look at the underside picture, you can see the roughness of the wood...and I had already lightly sanded them! I ripped my own 1x2's for the edging and "X" from 2x4's with my table saw because I could not find anyone who sold unwarped wood...so frustrating!! The wood was so much straighter when I ripped them. I will rip my own wood as much as possible for now on!!
The "X's" were a challenge and I ended up cutting the ends at a 47.5 degree angles. I do not know why I had such a problem. I had right angles, but the wood is imperfect in many ways and not perfectly straight. I attached the "X's" together and to the table with glue and pocket holes. The legs had ink stamping, so I tried to keep that and not sand the ink completely off.
I added the metal "bling." I dulled the metal, primed and painted with metal paint. The paint chips off easily. So I think will end up replacing these pieces later on. The bolts were originally black, so they will stay.
Total time...several weeks because of all the sanding. I cannot devote whole days to woodworking because of family and work and I can only sand one hour at a time before my hands start to go numb. Also, the Waterlox requires at least 24 hours between each application. Cost: approximately $15...for the pocket holes screws (fine Kreg screws), hardware, other wood screws and 1 8ft 2x4. Everything else I already had (I already had the Waterlox, bolts, screws) or was given to me (pallets).

Skipped the 2x4 top and shelf and replaced with a 1x4 board. Got lucky with some scraps. The Colorado logo was distressed with a rotary sander. 

I would like to thank www.stonecoatcountertops.com for the ideas on the countertops, 

first off I used 3/4 MDF for this project, Ana White's momplex cabinet plans and just extended the plans to the size i needed, i created the doors out of MDF cut to size and used a router to create the design on the edge and the countertops are made with MDF, expoxy,spray paint, and metallic powder in 91% alcohol. this plan was so eazy, and my kids had a blast doing it, Thanks Ana for the cabinet plans

My daughter had all of her collection of Pretty Pony's in boxes, and like mother, like daughter, she likes working with her hands. She restrings their hair, paints new designs on their bottoms, etc. She loved the look of the 25 cubbies, just wanted them bigger across to accomadate her ponies.
These shelves are customized just for her toys, I used 1x4 instead of 1x6 because I don't want her bumping her head, when she gets out of bed....I didn't need that much width.
My daughter drew the Scalloped edge on freehand, and I cut it out.
Love this project.

My husband made this for my daughter's 4th birthday. she loves it! We did decided not to add the wheels and it seems to be fine without them. We chose to do her name in letters as well. I did the lines and dots with a sharpe marker.

I built this for my oldest brother.  I only used 2x2's for the legs.  I built the carcuses out of plywood and used 1x2 select pine for the face frames.  I built the top shelfs to be 5 feet tall.  So the whole thing is 7 feet high by 8 feet wide.  

We needed a surround for the TV and really wanted to have a fireplace underneath. I took the Shanty Hutch/Sideboard plans and made some modifications. Took about 2 weeks to complete.

This was a fun easy & free project! I had a number of 1x4's left over from building the Classic Bunkbed and we paired that with some old knobs I saved. These 3 peg boards have made a great addition to the foyer of our house. We use them to keep purses, bags, dog leashes, and hats handy and still organized. I am tempted to put up a few more peg boards in our hall now!

This probably took 30 minutes total from inception to installation.

We took the general plan of the Cassidy wood shim bed but added some features of our own. Since my husband is in the military we knew we would be moving more than the average builder so we made the bed to be more durable for frequent disassemblies. Instead of screwing the frame to the head and foot board we used carriage bolts to secure the pieces.

We also wanted to add a reclaimed aspect to our bedroom. We bought some reclaim cedar siding from a local estate investor and decided to do a chevron pattern. After staining the whole frame, we applied the siding to both the head and the foot board since we bought basic plywood and wanted to cover both ends. Plus, we liked the look with both ends done better. We cut the siding at 45 degree angles and then custom cut each piece to fit. This was a time consuming area since, with reclaimed wood especially, each piece is unique. We then just used liquid nails to secure the pieces.

To finish we assembled the bed and applied a paste wax.

This was my first Ana White project and the first time using my new Kreg jig that my wife bought for me as a birthday gift.  I modified the plans to build this as one complete unit and not as separate bins to be stacked.  I used my Kreg jig on the dividers and ends to attach each section to the next.  This saved on material and made it a bit lighter since I was building it 4 units high.  I added small 2x3 feet to the bottom to clear an outlet behind the toy bin.  Two L brackets were used to anchor the unit to the wall. 

Instead of using galvanized pipes, to save money we opted for ready made closer rod & hardware from Lowe’s and added additional 2x4 pieces perpendicular to the shelf supports and screwed the closet rods into those. 

My couches were inherited from my mom, and she loves everything BIG. So I have very deep, very tall and very BIG sofas that need a hefty table to hold it's own between them. I was working on converting the dimensions of the modern farm table on my own, but Miss Ana is known to be a mind reader, and drew up these plans before I finished mine!

I am terrible when it comes to a) reading the advice given in comments and b.) finishing, so I didn't know it would be absolutely beneficial to stain these pieces before assembly... OOPS! At least it's in a corner! :-p

Maui Costco had a craft table but I waited too long to go back (1 week!) and they were sold out & discontinued. I stumbled across Ana White's website and found the "modern craft table." After a couple of modifications I am extremely happy with the results, as is my Golden Retriever "Buddy" who likes hanging out underneath while I am working. And yes, he has a mohawk!

I used the plans from Michaela's kitchen island, but modified the top. Instead of 2x4s pine studs, I used black walnut boards a friend of mine had lying around. They were ~1x8" boards so I ripped them to ~4" width and ~60" length. They were a little warped so I glued and screwed them togther using a Kreg jig (best tool ever). This made a huge difference and there was only minimal gaps (1/16") between the boards. I ended up borrowing a belt sander from another friend to take out the 1/16"-1/8" lips in the boards. First time using a belt sander and it took a few minutes with 80 grit across the grain to get a level surface. Used 120 grit paper with the grain to smooth out the scratch marks from the 80 grit. Attached the top to the base with screws, finish sanded with 220 and 320 grit, cleaned up the dust with a tack cloth and then applied a few coats of polyurethane. For the drawers, I couldn't find 21" slides so I ended up modifying the drawers for 20" slides. Another fun and satisfying project!

I built this bookcase for a friends son for Christmas. She sent me a sketch of what she wanted and I drew up the plans in sketch up. I built it out of plywood and capped plywood with poplar strips. I made the Cedar shingles out of Cedar shims that I cut down to 2 inches, I used corrugated metal for door panels to give garage look.

I've been wanting the pottery barn decorative ledge forever! I saw the picture online and was hoping I could find a tutorial for it. I ran across a couple but they weren't quite as big as the original and I wanted it to hang above my king size bed. So yesterday I headed out to my garage where I new I had a bunch of scraps/leftovers from my projects as well as my neighbor brought over some of his scap wood. I printed of the PB picture and wrote down the dimensions and got to work! This was my final result.

Finished this project using scrap pine for the frame and shelves and old barn wood for the doors/siding/table top. Turned out great, can't wait for other projects to finish.