Community Brag Posts

This has to be one of our favorite Ana projects so far! And our first using the Kreg Jig - which I now love!
Much to the dismay of the neighbor kids next door - it's not a candy stand. Nope, for now it's destined to be my little red potting bench.

My son wanted a bigger bed so when his friends and cousins sleep over they dont have to squeeze into his twin. My son is 12 by the way, so when I got a king I gave him my queen. I needed to raise it up because I knew I wanted to build a trundle to put under it. This bed is pretty heavy, very sturdy (even with 5 kids sleeping on it or jumping on it) I took the idea from my Malm bed from ikea but its a lot heavier and stronger

Used a vinegar and steel wool solution. Also put some six inch 1x6 3 inches from the bottom as a bracket to mount to a full bed frame. If I later upgrade to a queen I will but the wood bracket flush and reattach

Thanks for all the ideas. Wanted to share my build with everyone. 

I worked on this by myself for 1 month...i am exhausted, still need to glue the flase drawer fronts, but am overall happy with it, still functional.

I made this bed for my daughter's birthday using poplar wood. Since I can only work at night after the kids are in bed I think it took me about 3 nights working an hour or two each night to build it and then a Saturday afternoon to finish it. I finished it using a Miniwax pre-stain, Miniwax English Chestnut stain, and then completed it with a couple coats of polyurethane.

She actually helped me at the end to stencil on the names of her dolls, a couple butterflies and a flower on the bottom of the top bunk so her baby had a pretty picture to look at while she slept :). She loves the bed.

We also worked together to make her cousin a single bed that I will share photos of also. Thank you so much for sharing the plans with us!

We modified the size slighly 54x16x29 and added a 1" reveal at the front. The top is made of 1" cedar planks. All the wood we used for this project was free recyled wood. The top color is expresso satin and the support structure is pure white.

Another fun build! I increased the size to 4’W x 7’T and added some drawers! Thanks for your detailed plans. 

First Project. Finished it all except the hardware just in time for my Mother-in-laws birthday party. Pictures are from my phone decorated for the party w/o the hardware, and then after, finally complete with the hardware.

Needed a small table for our new house so I decided to build one, I followed the design fairly close. The only creative difference and I'm going to pretend I meant to do it was that I rotated the squares 90 degrees.

A few tips / things to look out for:

- The angled legs are tricky to line up/attach but you can use alot of woodfiller there to fill in the gaps and you can barely notice it once it is all together.

- When attaching the slats to create the squares for the top, add 5 pocket hole screws to each side, when you go to attach them you will thank me, 3 on each side of them doesn't hold as tight as you need it too.

- on the underside of the top I also added some scrap squares of 1x4 under the small triangles to stop them flexing, attached to the 2x6 with pockethole screws.

- Palm Sander - should be listed as required tool, to level out the top after assembly I went through a pack of 120 grit discs.

- There is not much room for error if you only have 2 8 foot 2x6's so cut them a couple blade widths bigger than you measure and sand them down to exact size.

as I used SPF for the table top I think I am going to get a piece of tempered glass cut for the top to protect the soft wood and give me an easy surface to clean.

Went a little crazy on the pipe project, but love it.  My favorite thing is the bench.  My husband loves the toilet paper holder. 

I modified these plans a little. I added some tongue and groove breadboard ends, and used Rockler table top fasteners to attach the top. I worked on it in my spare time after work a couple days a week for about a month. I'm happy with the overall outcome!

For my second project I wanted to build something a little more difficult than a shelf.  The hubby showed me how to use our power tools and I was unstoppable.  I chose this great bench because it fit the feel of our house and I wanted an entryway spot to sit while putting on shoes. 
The finishing took much longer than it actually took to build the bench.  I thought it would be more difficult to get the precise angle measurements  to make the supports under the bench, but it was not bad at all.  I can 't believe I built this pretty bench!  I have the building fever now!

I build this last minute for my daughters room makeover.  I worked through the night, but got it completed and painted just after sunrise. (I slept good the following night!)

This was so easy to make and it's so sturdy and beautiful. Rough cut cedar using 3" exterior decking screws and wood glue. Had a blast making it with my wife. 

This was the first project I tackled by myself. I think I spent about $70 and used pine.